PRODUCT SPECIFICATION Version 1.0 IEEE 802.11 a/b/g/n/ac 2T/2R Band USB2.0 Module Model Number: WC0HR2601 ( REALTEK RTL8812BU ) 2.4G channel: 1-13 5G channel: 36-48 149-165 (MAC address from GSD) 客户认可 Custom Approval Section Custom Name Department Approval Date: 拟制 DESIGN 审核 CHECK 批准 APPROVAL 高照 陈宇科 熊运自 2016.09.26 2016.09.26 2016.09.26 惠 州 高 盛 达 科 技 有 限 公 司 HUIZHOU GAOSHENGDA TECHNOLOGY CO., LTD 中国惠州仲恺高新技术开发区华宇路 75 号 HUA YU RD., NO.
PRODUCTS SPECIFICATION WC0HR2601 Document revision history Revision Version 1.0 Date Approved by 2016-09-26 Remarks Draft PAGE 2 OF 10 Version 1.
PRODUCTS SPECIFICATION 1. WC0HR2601 General Description This document is to specify the product requirements for 802.11a/b/g/n/ac and Bluetooth USB Module. This Card is based on REALTEK RTL8812BU chipset .It is a complete dual-band(2.4GHz and 5GHz)WIFI 2× 2 MIMO MAC/PHY/Radio System-on-a-Chip. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps.
PRODUCTS SPECIFICATION WC0HR2601 3. Application Diagrams 3.1 Functional Block Diagram 3.2 General Requirements 3.2.1 IEEE 802.11b Section Feature Detailed Description 3.2.1.1 3.2.1.2 3.2.1.3 Standard Radio and Modulation Schemes Operating Frequency 3.2.1.4 Channel Numbers 3.2.1.5 Data Rate Media Access Protocol 3.2.1.6 3.2.1.7 Transmitter Output Power at Antenna Connector 3.2.1.8 Receiver Sensitivity at Antenna Connector ● IEEE 802.11b ● DQPSK , DBPSK , DSSS , and CCK ● 2400 ~ 2483.
PRODUCTS SPECIFICATION WC0HR2601 3.2.2 IEEE 802.11g Section Feature Detailed Description 3.2.2.1 3.2.2.2 3.2.2.3 Standard Radio and Modulation Type Operating Frequency 3.2.2.4 Channel Numbers 3.2.2.5 Data Rate Media Access Protocol 3.2.2.6 3.2.2.7 Transmitter Output Power at Antenna Connector 3.2.2.8 Receiver Sensitivity at Antenna Connector ● IEEE 802.11g ● QPSK , BPSK , 16QAM ,64QAM with OFDM ● 2400 ~ 2483.
PRODUCTS SPECIFICATION WC0HR2601 3.2.4 IEEE 802.11n Section 3.2.4.1 3.2.4.2 Feature Detailed Description Standard ● IEEE 802.11n ● BPSK , QPSK , 16QAM ,64QAM with OFDM Operating ● Frequency ● 2.4GHz band:2400 ~ 2483.5MHz 5GHz and:5150 ~ 5825MHZ Radio and Modulation Type 3.2.4.3 MCS 3.2.4.4 3.2.4.5 Protocol Transmitter Output 3.2.4.6 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Data Rate Media Access Power at Antenna Connector GI=800ns 20MHz 6.5 13 19.5 26 39 52 58.
PRODUCTS SPECIFICATION WC0HR2601 3.2.5 IEEE 802.11ac Section 3.2.5.1 3.2.5.2 Feature Standard Radio and Modulation Type 3.2.5.3 Operating Frequency 3.2.5.4 Channel Numbers 3.2.5.5 Data Rate Media Access Protocol 3.2.5.6 Detailed Description ● IEEE 802.11ac ● QPSK , BPSK , 16QAM ,64QAM,256QAM with OFDM ● ● ● ● ● ● ● ● ● 5.15~5.35GHz and 5.725~5.825GHz for US and Canada 5.15~5.35GHz and 5.47~5.725GHz for Japan 5.15~5.35GHz and 5.47~5.725GHz for Europe 5.725~5.
PRODUCTS SPECIFICATION WC0HR2601 4. Electrical and Thermal Characteristics 4.1 Environmental Requirements Parameter Storage Temperature Ambient Operating Temperature Junction Temperature Minimum -40 0 0 Maximum +80 60 125 Units ℃ ℃ ℃ 4.2 General Section 5.2.1 5.2.2 5.2.3 5.2.4 Feature Detailed Description Antenna Type Operating Voltage Current Consumption Form Factor and Interface ● ● ● ● WIFI ANT :PIFA Antenna and IPEX 3.3 V±10% <1000mA High Speed USB2.0 Interface 4.
PRODUCTS SPECIFICATION WC0HR2601 5 Connector Definition 10-Pin 1.25 mm connector(Horizontal Type) Pin 1 3 3 4 5 6 7 8 9 10 Definition 3.3V 3.3V D- D+ GND WOWn RST GND NC GND 6 Mechanical Dimensions Note1: The below is left-off-board ANT diagram Note2:TOLERANCES ARE +/-0.5mm UNLESS OTHERWISE SPECIFIED * UNITE :mm PAGE 9 OF 10 Version 1.
PRODUCTS SPECIFICATION Appendix 1 : SMT connector WC0HR2601 GH-10AWB-GF This is the N pin connector which is in common use. You can select 10 pins according to your requirement. PAGE 10 OF 10 Version 1.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.