PRODUCT SPECIFICATION Version 1.3 IEEE 802.11 a/b/g/n/ac 2T/2R Dual Band Module Model Number: WC0DR2611 HUIZHOU GAOSHENGDA TECHNOLOGY CO.,LTD HUA YU RD., NO.
PRODUCTS SPECIFICATION WC0DR2611 Document revision history Revision Version 1.0 Version 1.1 Date Approved by 2016-05-25 Remarks Draft 1、 Connector :change 6PIN to 5PIN 2、 ADD Mechanical Dimensions: 2016-05-26 Module A ,Module B Version 1.2 Version 1.3 1、 Modify Dimensions 2、 Modify ANT2 2016-05-31 Mechanical SPEC 3、 Modify Connector SPEC 4、 Modify ANT2 SPEC 2016-06-07 PAGE 2 OF 12 Version 1.
PRODUCTS SPECIFICATION WC0DR2611 1.2 General Requirements 1.2.1 1.2.1.1 1.2.1.2 1.2.1.3 IEEE 802.11b Section Feature Standard Radio and Modulation Schemes Operating Frequency 1.2.1.4 Channel Numbers 1.2.1.5 Data Rate Media Access Protocol 1.2.1.6 1.2.1.7 Transmitter Output Power at Antenna Connector 1.2.1.8 Receiver Sensitivity at Antenna Connector 1.2.2 1.2.2.1 1.2.2.2 1.2.2.3 ● IEEE 802.11b ● DQPSK , DBPSK , DSSS , and CCK ● 2400 ～ 2483.
PRODUCTS SPECIFICATION WC0DR2611 1.2.3 IEEE 802.11a Section 1.2.3.1 1.2.1.2 Feature Standard Radio and Modulation Type 1.2.3.3 Operating Frequency 1.2.3.4 Channel Numbers 1.2.3.5 Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 1.2.3.6 1.2.3.7 1.2.3.8 Detailed Description ● IEEE 802.11a ● QPSK , BPSK , 16QAM ,64QAM with OFDM ● ● ● ● ● ● ● ● ● 5.15~5.25GHz and 5.725~5.825GHz for US and Canada 5.15~5.25GHz for Japan 5.15~5.
PRODUCTS SPECIFICATION WC0DR2611 ● 5GHz Band/HT20 ● 5GHz Band/HT40 ● ● 18 dBm at MCS8 ● ● 18 dBm at MCS8 12 dBm at MCS15 12 dBm at MCS15 Typical Sensitivity at each RF chain at Which Frame (1000-byte PDUs) Error Rate=10% and at room Temp. 25℃ 2.4GHz Band/HT20 Receiver Sensitivity at Antenna Connector 1.2.4.7 1.2.5 2.
PRODUCTS SPECIFICATION WC0DR2611 2. Electrical and Thermal Characteristics 2.1 Temperature Limit Ratings Parameter Storage Temperature Ambient Operating Temperature Junction Temperature 2.2 Minimum -40 0 0 Maximum +80 60 125 Units ℃ ℃ ℃ General Section Feature Detailed Description 2.2.1 Antenna Type 2.2.2 2.2.3 2.2.4 Operating Voltage Current Consumption Form Factor and Interface ● ANT1: Metal antenna ANT2: IPEX connector ● 5V±10% ● ＜900mA ● High Speed USB2.0 Interface 2.
PRODUCTS SPECIFICATION WC0DR2611 3. Connector Definition 5-Pin 1.25 mm connector（Horizontal Type） Pin Symbol 1 2 3 4 5 4 POWER_EN GND D+ DVCC（5V） Mechanical Dimensions ANT2 ANT1 *TOLERANCES ARE +/-0.5mm UNLESS OTHERWISE SPECIFIED *UNIT:mm PAGE 7 OF 12 Version 1.
PRODUCTS SPECIFICATION WC0DR2611 Appendix 1 : SMT connector GH-5AWB-GF This is the N pin connector which is in common use.You can select 5pin according to your requirement. PAGE 8 OF 12 Version 1.
PRODUCTS SPECIFICATION WC0DR2611 Appendix 2 : Antenna on board spec PAGE 9 OF 12 Version 1.
PRODUCTS SPECIFICATION WC0DR2611 Appendix 3 : Antenna off board spec PAGE 10 OF 12 Version 1.
PRODUCTS SPECIFICATION WC0DR2611 PAGE 11 OF 12 Version 1.
IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
The user manual for local area network devices shall contain instructions related to the restrictions mentioned in the above sections, namely that: (i) the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p.
Host Product Labelling Requirements: This transmitter module is authorization only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users.
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
