™ FPV HELICOPTER INSTRUCTION MANUAL No.
1 INTRODUCTION Thank you for buying HUBSAN products. The helicopter is designed as an easy to use, full featured RC helicopter model capable of all forms of rotary flight. Please read the manual carefully before assembling the model, and follow all precautions and recommendations within the manual. Be sure to retain the manual for future reference, routine maintenance, and tuning. Remember, your helicopter is designed for indoor operation, where low-speed precision-control is paramount.
5. Don't forget to be ready to catch the helicopter's loss of lift. As you servos are creating a battery power drain, you will need to increase the collective Throttle while maintaining the Rudder input Exiting the Turn maneuver 6. At the end of the turn, begin to SUMULTANEOUSLY ease off the cyclic Roll, collective Rudder and the additional Throttle inputs. You should practice until you can simultaneously use all of the joystick inputs in smooth, synchronized movements.
2.3 PREVENT MOISTURE R/C models are composed of many precision electrical components. It is critical to keep the model and associated equipment away from condensation and other contaminants. Exposure to water or moisture may cause the model to malfunction resulting in loss of responsiveness, or a crash. 2.4 PROPER OPERATION For the safety purpose, please only use hubsan’s spare parts for replacement. 2.
6.4 Basic Maneuvering In this Flying Lesson you will use the cyclic joystick and the Rudder to maneuver your helicopter. 1.Keeping a safe 1 to 2 meters from your model, S-M-O-O-T-H-L-Y advance the collective Throttle joystick until your helicopter reaches approximately shoulder height. 2.S-L-O-W-L-Y apply collective Rudder control to point the nose of your helicopter in the direction you wish to fly. 4 TRANSMITTER 4.1 Identification and functional keys Main Menu Display 5805 HUBSAN 7.
Input Key Function S/N 6.3 Hovering and Cyclic Trim Identification Function Because your helicopter’s rotors create a ‘downdraft’ any attempt to hover at too low an altitude (height) is more difficult than hovering a little higher. This difficulty is because the downdraft from your rotors is bounced back off the ground, resulting in turbulent air around the helicopter-this is referred to as ‘Ground Effect’.
Although the helicopter’s trim has been factory set, you will need to fine tune the settings so that your helicopter can maintain a better balanced hover IMPORTANT: KEEP YOUR CONTROL INPUTS VERY S-L-O-W & GENTLE 1. Set the collective Throttle joystick and trim slider to its lowest setting. All other trim sliders should be at their mid positions. 2. After completing the ‘Power-On (Failsafe) Procedure’, place your model on a smooth, flat surface which will allow it to slide and turn (a landing board is idea).
4.2.4. RUDD REVERSE SET UP Hold down ENT key for 1 second to enter setting status.Press ENT key to enter reverse setting status.Move arrow to Rudder by up/down key ,Press ENT key to choose reverse and then hold EXT key for 2 seconds to confirm and exit. 5805 HUBSAN Set reverse Elevator Aileron Throttle Rudder Set sensitive Plane type Expert mode Stick mode 6.
5.4 Fitting the LiPo battery The supplied LiPo battery is mounted inside a cradle on the underside of your helicopter’s fuselage. The LiPo battery should be mounted with its connecting cables facing towards the rear or the helicopter 4.3 SENSITIVITY SET UP 4.3.1 RUDDER SENSITIVITY SET UP- NOR MODE Hold down ENT key for 1 second to enter setting status.Enter set sensitive status by up/down key,Press RUDDER TRIM KEY to idea sensitivity and then hold EXT key for 2 seconds to confirm and exit.
4.4 FPV MODULE 4.4.1. Your FPV helicopter equipped with a video camera, mounted under the bottom of helicopter, you can push the camera upward or downward to adjust the angle of aerial photography, please see the picture shows Insert the plug into the power jack Return the holder back to the compartment Fasten the screw 5 Li-Po Battery Charging 5.1 The helicopter is equipped with a LiPo battery: 7.4V 2 Cell 650mAh x 1 unit 4.4.2 Keep the FPV 5.
FCC warning statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
