Quick Guide

Quick Guide
2.Choose your
region, input
Mobile Number or
email and click
“Continue”.
3.Input the
verification code
from your email or
smart phone.
3. Add device to smart phone
1.Open HUANSO
Smart APP and
click “Register”.
Note: If user can’t setup device in above way, user can try below AP setup.
4. Set your login
password and
click “Done”.
5. Click Add Home.
6. Enter home
name and set
geographic
location, then click
“Done” to confirm.
7. App will auto login
after registration
1. Device
2. Install the APP
2.Click “+” button.
3.Choose Wifi
water sensor.
4. Click “Confirm
indicator rapidly
blink”.
5. Enter WiFi
password and click
“Confirm” button.
6. Wait until
co n nec tion
finished.
7. Input device
name and click
“Done” button.
8. Click device.
9.Enter device
control interface.
4. Click AP Mode
6. Enter WiFi
password and click
“Confirm” button.
5. Click “Confirm
indicator slowly
blink”.
8. Choose WiFi
hotpot “Smart
Life-xxx”. After
connected to the
WiFi hotpot,
return to the APP.
9. Wait until
connection
finished.
7. Click “Connect
now”.
10. Input device
name and click
“Done” button.
11. Click device.
12. Enter device
control interface.
4. APP Control
Back
More: Modify
device name,
Device sharing,
Device Info and
so on.
Battery status
V190226-2
1. Add battery,
indicator light
rapidly blink
twice per second
to enter
‘Smartconfig’
setup mode.
The current state
of Water sensor
Alarm history
Alarm notification
switch
2.Click “+” button.
Warning: Device use CR123A 3V dry battery only. Rechargable
battery RCR123A 4.2V is forbidden.
Specification
1pc CR123A 3V dry battery.
(Note: Rechargable battery RCR123A
4.2V is forbidden.)
3V
2.4GHz
802.11b/g/n
About 2 years if no detection
Battery model:
Operating Voltage:
WiFi frequency:
WiFi Protocol:
Standby Time:
“-”
“+”
Indicator light
Light rapidly blink
twice per second is
in ‘Smartconfig’
setup mode.
Light slowly blink
once per two
seconds is in ‘AP’
setup mode.
Maybe you use Android smart phone and you are in China
mainland but you register other country or Hong Kong APP
user account then you can't receive push notification. You
should register APP China mainland user account when you
are in China mainland for Android smartphone.
Maybe you use Android smart phone and register China
mainland user account but you have stop APP in the smart
There are 2 modes to setup, ‘Smartconfig’ setup mode and
‘AP’ setup mode.
User can long press device’s Wi-Fi button for 5 seconds to
switch between this 2 modes. Indicator light rapidly blink
twice per second is ‘Smartconfig’ setup mode, user should
click ‘Confirm indicator rapidly blink’ button in APP to setup.
Indicator light slowly blink once per 2 seconds is ‘AP’ setup
mode, user should click ‘AP Mode’ in the APP to setup.
Maybe you are using 5Ghz WiFi router, device don’t support
5Ghz WIFI, user should use 2.4GHz WiFi router to connect.
Maybe you input wrong WIFI password. Please input correct
password.
Maybe your router haven't open DHCP. Pls open DHCP in
your router.
Maybe device is too far away from the Wi-Fi router. Pls put
device close to router or add Wi-Fi repeater.
Maybe your router’s WiFi have special settings, pls reset
your router.
6. FAQ
Q1: Why does the device can’t be connected?
A1,
2,
3,
4,
5,
6,
Q2. Why I can't receive push notification alarm or miss some
push notification alarm?
A1,
2,
ph o nes ' ba c kgr oun d , th en y o u ca n't r ece ive p ush
notification. Android smart phone APP China mainland
user account should keep APP running at Android smart
phone’s background to receive push notification alarm.
Maybe device is too far away from the Wi-Fi router. Pls put
device close to router or add Wi-Fi repeater.
Device will only send push notification alarm every 1
minute to save battery. After 1 push notification it will not
push alarm within 1 minute.
Maybe in APP-Device-Notice-Detection Alarm is disable.
Pls enable it.
Ma ybe i n AP P-Pr ofi le- Sett ing s-P u sh N oti fic a tio n is
disable. Pls enable it.
Maybe when you install the APP you haven't allowed smart
phone to receive push notification of this APP. Pls check
your phone's notification center to enable receiving push
notification of this APP.
Maybe you use Android tablet, device don't support
Android tablet which will close Wi-Fi if screen closed.
Maybe you had turn off your phone's 3G/4G network then
you might miss some push notification alarm when battery
is low or WiFi is intermittently disconnected. You should
always turn on 3G/4G network to be receive push
notification all the time.
3,
4,
5,
6,
7,
8,
9,
WiFi button
Long press 5
seconds to
switch to
different setup
mode.
Buzzer
Cable Plug
1.When Wi-Fi indicator
light rapidly blinks
twice per second, long
press Wi-Fi button for
5 seconds again until
Wi-Fi indicator light
slowly blinks once per
2 seconds to enter AP
setup mode.
3.Choose Wifi
water sensor.
Scan QR code to intall APP or
“HUANSO Smart” from “Google Play Store”
install on the smart phone.
or “App Store” and
Click HUANSO Smart App , Register and log in
the account.
Download the APP
HUANSO Smart App
(Android)
(IOS)