Quick Guide

4.Click "device"
8. Click"edit name"
to input the control
command
9. Input control command,
click "confirm" and
"save "button
10. Click" add to Siri "
11. Click "add to Siri"
5.Choose "fan"
7. Select "on" and
click "save" button
6.Choose the function
you want to control,
such as " power"
1 3 7 8 9 10 1211
Quick Guide
FS200104-2
5
4 6
2. Install the App
Scan QR code to intall APP or HUANSO
Smart’
from ‘Google Play Store’ or ‘App Store’, and
install on smart phone.
Download the App ‘
Note: If user can’t setup device in above way, user can try below AP setup.
Note:
lowest speed.
Sleep wind is every half hour drops 1 speed from recent speed until drops to the
1. Introduction
4. APP control
3. Add device to smart phone
2
1. Click ‘+’ button.
2. Choose ‘Fan’
1. Click ‘+’ button.
2. Choose ‘Fan’
6. Wait until connection
finished.
4 . C l i c k ‘ C o n f i r m
indicator rapidly blink’.
7. Input device
name and click
‘Done’ button.
4. Click AP Mode.
5 . C l i c k ‘ C o n f i r m
indicator slowly blink’.
9. Wait until
con n ec tion
finished.
7. Click ‘Connect
Now’.
8. Choose Wi-Fi hotspot
‘SmartLife_xxxx’. After
connected to the WiFi
hotspot, return to the
APP.
1 0 . I n p u t
de vice name
a n d c l i c k
‘Done’ button.
11. Enter device
control interface.
5. Amazon Alexa Voice control
Back
On/OFF
Before controlling our smart device by Amazon Alexa, user should prepare Echo
device like Echo or Echo Tap or Echo Dot or Echo Show, Amazon Alexa APP and
Amazon Alexa account.
Enable our skill in Alexa APP.
More: Modify device
n a m e , C h e c k t h e
n e t w o r k , D e v i c e
sharing, Device Info,
Check for firmware
update and so on.
Wind Type
Timer
Speed
Timer: set on or
off schedule.
Countdown: To
s e t t u r n o f f
d e v i c e a f t e r
1/2/3/4 hours.
1, Open Ale x a
APP a n d log i n
A m a z o n
account. Choose
“Skill & Games”
User should click ‘DISCOVER DEVICES’ button in Alexa APP to discover the
devices, this may take longer than 20 seconds and found device will be shown in
the all devices list.
Or User also can say to your Echo: ‘Alexa, discover devices’. Alexa will start to find
devices been added in ‘HUANSO Smart’ APP. It will take about 20 seconds to show
result.
Discover device in Alexa APP
Note:
device again, otherwise Alexa can not control device.
Every time user change device name in ‘HUANSO Smart’ APP, Echo should re-discover
Voice control Fan by Amazon Alexa
➢Alexa, discover devices
➢Alexa, turn on/off ‘Fan’.
➢Alexa, set ‘Fan’ to one/two/three
Note: ‘Fan’ is the device name user add to ‘HUANSO Smart’ APP.
6. Google Home Voice Control
Link HUANSO Smart account in Home Control
Make sure Google Home is connected to network.
Before controlling our smart device by Google Home, user should prepare Google Home
device like Google Home or Google Home Mini, Google Home APP or Google APP for Android
and Google account.
1.Click this button
2. Choose ‘Home
3.Click ‘+’ button
4. Find ‘Smart Life’ in
t h e s k i l l l i s t a n d
select to open it.
5 . C h o o s e y o u r
c o u n t r y a n d i n p u t
y o u r ‘ H U A N S O
Smart’ APP account
and password.
6. Click ‘Link Now’.
7. Afte r click ‘ Link
Now’ if it shows this
interface, user should
c h o o s e ‘ H U A N S O
Smart’.
9 . D e v i c e l is t c a n b e
c o n t r o l l e d b y G o o g l e
H o m e , s a y t o G o o g l e
Home: ‘OK Google, sync
new devices’ to find and
add new devices.
8. Click ‘Done
6 . E n t e r W i - F i
Password and click
‘Confirm’button.
Oscillating
5 . E n t e r W i - F i
password and click
‘Confirm’ button.
1.Open HUANSO
Smart APP and
click ‘Register’.
2. Choose your
r e g i o n , i n p u t
Mob i l e N u m b e r
or email and click
‘Next’.
3 . I n p u t
verification code
from your email
or smart phone.
4.Set your login
p a s s w o r d a n d
click confirm.
5. Click Add Home.
6 . I n p u t h o m e
n a m e a n d
g e o g r a p h i c
location, then click
‘Done’ to confirm.
7.App will auto login
after registration.
Note: If it doesn’t rapidly blink twice per second, long press Wi-Fi button for 5 seconds until
device beep and release and wait until Wi-Fi indicator light rapidly blinks twice per second.
There are 2 modes to setup, ’Smartconfig' setup mode and ‘AP’ setup mode. Indicator light
rapidly blinks twice per second is ‘Smartconfig' setup mode, user should click 'Confirm
indicator rapidly blink' button in APP to setup. Indicator light slowly blinks once per two
seconds is ‘AP' setup mode, user should click 'AP Mode' button in APP to setup. User can
long press device's Wi-Fi button for 5 seconds to switch between these 2 modes.
Maybe you are using 5Ghz WiFi router, device don’t support 5Ghz WIFI, user should use
2.4GHz WiFi router to connect.
Maybe you input wrong WIFI password. Please input correct password.
Maybe your router haven't open DHCP. Pls open DHCP in your router.
Maybe device is too far away from the WiFi router. Pls put device close to router or add WiFi
repeater.
Maybe your router ’s WiFi have special settings, pls reset your router.
Note: After add new device in the APP, say to the Google Home:’sync new devices’ to voice
control new devices. If it can’t find new device, user can find Action ‘HUANSO Smart’ in
Google Home APP to disable and Link again to voice control new devices.
FAQ
Q1 Why I can't setup device?
A:
1,
2,
3,
4,
5,
6,
HUANSO Smart App
(Android)
(IOS)
Timer indicator light
Speed Indicator light
Speed button, Long
press 5 seconds to switch
between sleep mode and
normal mode
Timer button
On/Off button, Long
press to setup Wi-Fi
Sleep mode indicator light.
Light on is sleep wind
Light off is normal wind.
Wi-Fi Indicator light.
Light always on is Wi-Fi setup
succeed and connected to
router.Light off is WiFi setup
succeed but loose connection
of router.Light rapidly blink
t w i c e p e r s e c o n d i s i n
‘Sma r tconf i g’ se tup mode .
Light slowly blink once per 2
seconds is in AP setup mode.
Oscillating Button
3. After power on the
device, Wi-Fi indicator
light will rapidly blinks
tw i c e p er s ec ond t o
e n t e r ‘ S m a r t c o n f i g ’
setup mode.
3. When Wi-Fi indicator light
rapidly blinks, long press Wi-Fi
button for 5 seconds again until
device Beep and release.Wi-Fi
indicator light will slowly blinks
once per 2 seconds and enter
AP setup mode.
3, Ch oose your
country and input
y o u r ‘ H U A N S O
S m a r t ’ A P P
a c c o u n t a n d
password.
4, Click ‘Link
Now’ button to
l i n k y o u r
‘ H U A N S O
Smart’ account
to your echo.
5, Choose ‘HUANSO
Smart’ and click Link
Now.
6, Click ‘Authorize’
User can also find the new devices in ‘all devices’ list.
2, Search ‘Smart
Life’ and choose
‘Smart Life’ skill
i n t h e s e a r c h
r e s u l t . C l i c k
‘ E N A B L E T O
USE ’ b u tton to
enable Skill.
7.Siri Voice Control：Power, Speed, Mode, Oscillating
Connection instruction
Note: Siri voice control can only be used by iOS version 12.0 or above.
2.Click"+"
3. Click"+''button
to add action
14.
to save phrase.
Click 'Done' button
Why can't I use Siri?
Maybe your iPhone version is too low,please update to version 12.0 or above to control Siri voice
control function.
Maybe it is iPhone bug because some version iPhone sometime can not call Siri to do anything
when using 3G/4G network. Pls try WiFi network if use WiFi network can voice control this device
means the device has no problem, then you should ask Apple company to fix your iPhone 3G/4G
network can not call Siri problem.
Q2
A:
1,
2,
Maybe your Phrase is already in use as a Shortcut before. Siri can not use same Phrases for 2
Shortcuts. You can re-record a new phrase. Or if you want to use the old Phrase, you can enter
your iPhone's Settings->Siri&Search->MyShortcuts and click 'edit' button to delet the old
Shortcut and Add the Phrase to Siri again in our APP.
Q3 Why I can not add to Siri?
A:
3 speeds
1hour/2hour/3hour/4hour/network timer
Optional: AC 100V(Japan) or
AC 110V(Taiwan)or
AC 120V(America) or
AC 220V~240V(Europe, Australia, China, Korea)
Warning: Don’t plug 100V or 110V or 120V fan to 220V~240V power.
45W
2.4GHz
802.11b/g/n
Antenna in PCB
Wind Speed:
Timer:
Voltage:
Actual Power:
WiFi Frequency:
WiFi Protocol:
WiFi Antenna:
Specification
Q4
A:
1,
2,
3,
4,
Why I can't voice control device?
Maybe your smart speaker or smartphone didn't hear what you say, pls try to say again.
Maybe the device name you set is misunderstood as another action the smart speaker or
smartphone should do. Pls change the device name to another name which your smart
speaker or smartphone will not misunderstand.
Maybe the device name you say to the smart speaker or smartphone is different from the
device name you set in the APP. Pls say the correct device name set in the APP to the
smart speaker or smartphone.
Maybe your smart speaker, smartphone or smart device network is disconnected, pls
check your network and try again.
8. Enter device
control interface.
Note: say to the phone: 'OK Google' to wake up Google Assistant.
5.Click "+"
Do w nl o a d t h es e t hr e e AP P “G o og l e” , “ Go o gl e
Assistant” and “Google Home” from Google Play Store.
8. Google Assistant Voice ControlAndroid Smartphone
1. Open the APP “Google” to set accessing your Assistant with your voice.
4.Use Google Assistant
Voice control Fan by Google Assistant
Sync new devices
Turn on/off “Fan”.
Set “Fan” to low/medium/high
➢ OK Google,
➢ OK Google,
➢ OK Google,
Note: 'Fan' is the device name user add to 'HUANSO smart' APP
1.Click Settings
2.Click More
Settings
3.Click Assistant
4.Click Home Control
11.Click“Authorize”
12. Click “DONE”
1. Say 'OK Google'
to wake up Google
Assistant.
2. Say control command,
such as ”Turn on fan”
2.Open the APP “Google Home” and then sign in your Google account.
3. Link HUANSO Smart account in Home Control.
5. Choose “Access
with Voice Match”
6.Click NEXT
7.Click I AGREE
6.Click to search
“Smart Life”
8.Choose your country, and
input your “HUANSO smart”
APP account and password.
10.After click ‘Link Now’
if it shows this interface,
user should choose
“HUANSO smart”
7.Choose “Smart Life”
9.Click “Link Now”
13. Device list can be
c o n t ro ll e d by Go og l e
Assistant, say to Google
As s i s ta n t : 's y n c n e w
devices' to find and add
new devices
Voice control Smart Fan by Google Home
➢ Ok Google, sync new devices.
➢ Ok Google, turn on/off ‘Fan’.
➢ Ok Google, set 'Fan' to low/medium/high
Note: ‘Fan’ is the device name user add to ‘Huanso Smart’ APP.
12.
to record your
personalised phrase
Click red button
13.
you want to record.
Say the phrase
3.Click Voice
4.Click Voice Match
1.Click More
2.Click Settings
1.Click here to turn
on/off Fan
2.Drag the icon to set Fan to
different speed. (1%-33% is
sp e e d one, 3 4 %-66% i s
speed two, 67%-100% is
speed three)
3.Drag the icon to set
Fan to one/two/three
speed.
1.Click"smart"