Wireless Driveway Alarm System User Manual
1.
OFF ON POWER VOLUME 14VDC CH4 CH3 CH2 CH1 ON/OFF: power switch(turn on/off the alarm receiver) POWER : power jack(DC12V-15V) VOLUME : adjust the alarm volume of the alarm receiver other alarm system siren 14VDC CH4 CH3 CH2 CH1 Output Interface 14V DC: used to connect extra siren CH1-CH4: relay outputs(normally open or normally close optional); used to connect to other alarm system(CH1-CH4 corresponding to Zone1-Zone4;relay output rating is DC24V or exchange 120V2A current) Solar & Wireless
Horizontal Pipe: easy to know the beams be installed vertically Infrared Beam: used to detect the intruder Calibration Hole: easy to align with another beam sensor if the beams apart far away Solar Panel: charge the battery of the beam sensor even in cloudy or rainy days LCD Display: easy to know how well the beam sensor be aligned with each other ON/OFF: turn on/off the solar beam sensor Charge Jack:pull out the red plug to charge the solar beam sensor by DC5V-12V power adapter if the battery of the beam s
Step2: Turn on the Solar &Wireless Photoelectric Beams: Press the ON/OFF button 3 times(Both the transmitter and receiver) Transmitter Receiver (more than 3 short beeps mean the built-in batteries of the sensor have enough power) Step 3 Make sure the beams aligned with each other (bleep prompt and LCD display more than “100” means the beam sensors work properly, Please note: “100” is a reference value, different weather will get different value and bigger value means better alignment ) Step 4 Power on the
Step 5 Trigger The Solar&Wireless Photoelectric Beam Sensor (Completely block all the 3 infrared beams by thick materials,such as books) ( LCD display “000” means the beam sensor be triggered and alarm receiver alarms--Zone 4 light up) Step 6 Installations Alarm Receiver Solar&Wireless Photoelectric Beam Sensor 1st Installation method 5
R T T R Calibration (1)Place the beam sensor on the same height. (2)Ensure the beam sensor is vertical (the bubble of the horizontal pipe should be in the middle). (3)Adjust the direction of the beam sensor to make them align with each other. Calibration Hole:used to find another device. LCD Display:used to know how well the beam sensor be aligned with each other (the LCD Display will shut down in an hour).
2nd Installation method(with iron brackets) Please note:the package not includes the iron brackets Iron Bracket 7 Iron Bracket
R T T R Calibration (1)Place the beam sensor on the same height. (2)Ensure the beam sensor is vertical (the bubble of the horizontal pipe should be in the middle). (3)Adjust the direction of the beam sensor to make them align with each other. Calibration Hole:used to find another device. LCD Display:used to know how well the beam sensor be aligned with each other (the LCD Display will shut down in an hour).
Step 7 Test and verify the alignment Block the infrared beams by thick materials(such as books) (1) Block only top 2 beams---No Alarm ( 2 ) Block only bottom 2 beams---No Alarm (3)Block all 3 beams---Alarm The same way to test and verify another sensor (1) (2) (3) 4.
Step 3 Trigger the detector(for example,trigger the solar&wireless photoelectric beam sensor) The indicator light of the the selected zone will blink and bleep prompt(that means the operation was successful) Step 4 Long time press the “select” button and release the button when the“ Power”indicator light up Step 5 Trigger the detector again to verify that the detector has been added to the receiver DELETE Step 1:Power on the alarm receiver and turn on the alarm receiver Step 2: long time press the “Select
(2)How to enable or disable the “disarming” function Enable Power on the alarm receiver and turn on the alarm receiver Long time press the “Pause” button and release the button when the “Power” indicator light blink(the alarm receiver will not alarm for 5 minutes even if the detector be triggered) ; Disable Long time press the “Pause” button and release the button when the “Power” indicator light not blink Or the receiver will disable the “disarming“ function automatically after 5 minutes (3)How to enable
(5)How to program the sensitivity of the solar beams Sensitivity of the solar beams divided into 2 types: 200ms (factory default) and 100ms Please follow up the operation steps if you want to switch the sensitivity of the beams to be 100ms Step 1: Turn on the solar beams by press the ON/OFF button 3 times (both the transmitter and receiver) Step 2: Long time press the ON/OFF button for 10 seconds and release the button when you hear bleep prompt,and then press the ON/OFF button 6 times quickly(operate the t
Solar&Wireless Photoelectric Beam Sensor 39mm 245mm 40mm 85mm 40mm 184mm 84mm 45mm Technical parameters Item Infrared Detection Range Wireless Transmission Range Beam Quantity Wireless Frequency Technical Parameters 100m(300 feet) 1KM(3000 feet) 3 433MHz FSK+FHSS Maximum Trigger Number In 24 Hours ≤200 times Working Voltage Battery Type Battery Capacity Static working Current Infrared Wavelength 3.3V Chargeable LiFePO4 Battery Transmitter:500mAh,Receiver:500mAh ≤0.
