User's Manual

ManualsBrandsHTZSAFE ManualsElectronicsRemote Control

Table Of Contents

Wireless Doorbell

User Manual

1. System Components And Usage

Plug-in Receiver

Note:The alarm system has been programmed already,

please operate the system according to the part 2 of

the manual;

Power Plug:plug the receiver into a socket

Volume

Melody

Indicator Light

Power Plug

If you want to add additional HTZSAFE sensors

to the system,please operate the system according to

the part 3 of the manual or contact us directly.

(E-mail:contact@saferhomee.com)

Volume: 4 volume levels adjustable

Melody: 35 classic melodies optional

Indicator Light: flash for several seconds when the push button

be activated

Summary of content (10 pages)

PAGE 1
Wireless Doorbell User Manual Note:The alarm system has been programmed already, please operate the system according to the part 2 of the manual; If you want to add additional HTZSAFE sensors to the system,please operate the system according to the part 3 of the manual or contact us directly. (E-mail:contact@saferhomee.com) 1.
PAGE 2
Speaker Speaker:sound for several seconds when the push button be activated Wireless Push Button Indicator Light Push Button Indicator Light: flash once each time the push button be activated; Push Button: Press to activate 2
PAGE 3
Cover Waterproof Shell Waterproof Shell and Cover:put the shell on the button and then use the cover to fixed. - + Battery Compartment Battery Compartment: 1 pieces 12V 23A battery(included) 2.
PAGE 4
Step2 Press the push button once The indicator light of the button will flash once if the button be activated Step 3 Press “Melody” once to choose the melody for this push button, total 35 melodies optional. Melody Step 4 Press the “Volume” once to adjust the volume of the receiver.
PAGE 5
How to fix the waterproof shell to the push button if the push button will be intalled outdoor,please fix the waterproof shell to the push button (1)put the shell on the button (2)use the cover to fix How to replace the batteries of the push button (1)pry open the back cover by a screwdriver (2)replace the battery(1pcs 12V 23A battery,please note the anode and cathode) (3)put the cover back.
PAGE 6
3.
PAGE 7
Step 3 Activate the additional push button. Note:please make the push button close to the receiver flashing quickly (the indicator light flashing once means the button was activated properly) (a ring tone prompt and the indicator light flashing quickly means the button has been added to the wireless alarm receiver successfully) Step4 Activate the push button again to confirm it has been added to the receiver already. Step 5 Press”Melody”button to choose the melody for this push button.
PAGE 8
Melody Volume (3)How to change the melody for the push buttons (total 35 melodies optional,match different melody with different push buttons) Step 1 Plug the receiver into a outlet Step 2 Activate the push button first,and then press the “Melody” button to choose the melody for this push button Same steps for other push buttons which have been added to the receiver already. 4.
PAGE 9
Technical parameters Working Current Technical Parameters (RX) AC 110V-220V Static Current 20mA; Alarming Current 300mA Wireless Frequency 434.6 MHz FSK+FHSS Item Working Voltage Wireless Push Button 76mm 15mm 42mm Technical parameters Item Wireless Transmission Range Wireless Frequency Working Voltage Battery Type Working Current Working Temperature Range 9 Technical Parameters (TX) 600 Feet 434.6MHz FSK+FHSS 12V 1PCS 12V 23A Battery Static<0.1mA; Alarming<60mA -10℃ to 55℃ 26-HB201811-805A(1.
PAGE 10
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.