User Manual

ManualsBrandsHTZSAFE ManualsElectronicsSolar Driveway Alarm System-1/4 Mile Long Transmission Range-Solar Powered No Need Replace Batteries-Outdoor Weatherproof Motion Sensor&Detector DIY Security Alert System

Table Of Contents

Wireless Alarm System

User Manual

1. System Components And Usage

Note:

contact@saferhomee.com

1.The alarm system is pre-programmed , please

proceed to part 2 of the manual for setup. (Or please

search “HTZSAFE T704&805A SETUP“ on YouTube,

there is a video for your reference)

2.If you want to add additional HTZSAFE sensors to

the system, program them according to part 3 of the

manual or contact us directly. (Or please search

“HTZSAFE T704 to 805A Connect “ on YouTube, there

is a video for your reference)

After-sale Service:

E-mail:

Plug-in Receiver

Power Plug:plug the receiver into an outlet

Volume

Melody

Indicator Light

Power Plug

Volume: 4 adjustable volume levels

Melody: 35 optional classic melodies

Indicator Light: flashes for several seconds when the sensor

is activated

Summary of content (12 pages)

PAGE 1
Wireless Alarm System User Manual Note: 1.The alarm system is pre-programmed , please proceed to part 2 of the manual for setup. (Or please search “HTZSAFE T704&805A SETUP“ on YouTube, there is a video for your reference) 2.If you want to add additional HTZSAFE sensors to the system, program them according to part 3 of the manual or contact us directly. (Or please search “HTZSAFE T704 to 805A Connect “ on YouTube, there is a video for your reference) After-sale Service: E-mail:contact@saferhomee.com 1.
PAGE 2
Speaker Speaker:sounds for several seconds when the sensor is activated Solar Wireless Motion Sensor Solar Panel Sensor Eye Drain Hole Sensor Eye: detects heat movements Solar Panel:charges the built-in battery of the sensor Drain Hole:used to drain out the rainwater(please note the drain hole must be facing down when you install the sensor) Charge Jack ON/OFF Charge Jack:used to connect the additional solar panel or DC 5V power adapter ON/OFF:sensor on/off 2
PAGE 3
ATTENTION PLEASE The KIT includes a USB charging cord without a AC adapter which is used to manually charge the solar sensor before use or after pro- longed low light conditions causing low battery. Please kindly connect the charging cord with your own USB plug(such as the direct USB outlet, the phone's USB plug or computer's USB, etc.).
PAGE 4
2.
PAGE 5
Step 3 Activate The Wireless Motion Sensor (wait about 30 seconds after you turn on the sensor) 1st method:press the ON/OFF button twice ON/OFF (press twice) (the light of the ON/OFF button will flash once meaning the motion sensor was activated and sent the wireless signal) 2nd method: Walk through in front of the sensor to acivate 1 foot a way (the light of the ON/OFF button will flash once meaning the motion sensor was activated and sent the wireless signal;then the motion sensor will automatically r
PAGE 6
Step 4 Press “Melody” once to choose the melody for this sensor, total 35 optional melodies. Melody Step 5 Same operation if you have the additional sensor, and please refer to part 3 of the manual for other settings.
PAGE 7
Installation Notes: 1. Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind. 2.Please point the sensor towards a open field (not towards the trees or bushes) 3.please adjust the sensor a little down(never upwards) 4.please point the sensor eye towards to the engine or exhaust pipe if detecting vehicles.
PAGE 8
3.
PAGE 9
Step 3 Activate the sensor. Note: please have the sensor close to the plug- in receiver when programming. flashing quickly ON/OFF (press twice) (a ring tone prompt and the indicator (the light of the ON/OFF button will flash once meaning the motion light flashes quickly meaning the sensor has been added to the plug-in sensor was activated and sent receiver successfully) the wireless signal) Step 4 Activate the sensor again to confirm the sensor has been added to the receiver already.
PAGE 10
(3)How to adjust the volume Step 1 Plug the receiver into an outlet Step 2 Press the “Volume” once to adjust the volume of the receiver.
PAGE 11
Step 2 To select Low sensitivity- - - - turn on the sensor by pressing the ON/ OFF button 3 times. To select Medium sensitivity- - - - turn on the sensor by pressing the ON/OFF button 4 times. To select High sensitivity----turn on the sensor by pressing the ON/ OFF button 5 times. 4.
PAGE 12
Wireless Motion Sensor 92mm 45mm 103mm 90mm Technical parameters Item Detection Range Detection Angle Wireless Transmission Range Wireless Frequency Working Voltage Battery Type Battery Capacity Working Current Solar Panel Output Current Working Temperature Range Technical Parameters Low sensitivity--25feet(7.5m) Mid sensitivity--30feet(9m) High sensitivity--50feet(15m) 15 1/4 Mile(400m) 433MHz FSK+FHSS 3.