User Manual

ManualsBrandsHTZSAFE ManualsElectronicsSolar Driveway Alarm System-1/4 Mile Long Transmission Range-Solar Powered No Need Replace Batteries-Outdoor Weatherproof Motion Sensor&Detector DIY Security Alert-1 Receiver and 2 Sensors KIT

Table Of Contents

Wireless Alarm System

User Manual

1. System Components And Usage

Plug-in Receiver

Volume

Melody

Indicator Light

Power Plug

Note:

contact@saferhomee.com

1.The alarm system is pre-programmed , please

proceed to part 2 of the manual for setup. (Or please

search “HTZSAFE T804&808A SETUP“ on YouTube,

there is a video for your reference.)

2.If you want to add additional HTZSAFE sensors/receivers

to the system, program them according to part 3 of the

manual or contact us directly. (Or please search

“HTZSAFE T804 to 808A Connect “ on YouTube, there

is a video for your reference.)

After-sale Service:

E-mail:

Summary of content (11 pages)

PAGE 1
Wireless Alarm System User Manual Note: 1.The alarm system is pre-programmed , please proceed to part 2 of the manual for setup. (Or please search “HTZSAFE T804&808A SETUP“ on YouTube, there is a video for your reference.) 2.If you want to add additional HTZSAFE sensors/receivers to the system, program them according to part 3 of the manual or contact us directly. (Or please search “HTZSAFE T804 to 808A Connect “ on YouTube, there is a video for your reference.
PAGE 2
Power Plug:plug the receiver into an outlet. Volume: 4 adjustable volume levels. Melody: 35 optional melodies. Indicator Light: flashes for several seconds when the sensor is activated/flashes once each 8 seconds if the battery of the sensors go flat. Speaker Speaker:sounds for several seconds when the sensor is activated. Wireless Motion Sensor Sensor Eye Sensor Eye: detects heat movements.
PAGE 3
Indicator Light Sensitivity Switches Battery Compartment Indicator Light: flashes once meaning the motion sensor was activated and sent the wireless signal. Battery Compartment: please insert 3 pieces AA 1.5V Alkaline batteries (not included). Sensitivity Switches: used to adjust the sensitivity of the sensor (High/Low adjustable). 2. Operation Instructions Step 1 Plug the receiver into an outlet. The indicator light of the receiver will flash once and a beep prompt meaning normal operation.
PAGE 4
Step 2 Select the sensitivity (High / Low) If High sensitivity, the detection range of the sensor is 50 feet; If Low sensitivity, the detection range of the sensor is 35 feet. Sensitivity Switches Step 3 Insert the 3pcs AA 1.5V Alkaline Batteries and note the anode and cathode (Batteries are not included). (Indicator lights will be on for 5 seconds meaning work properly, and wait about 30 seconds to activate the sensor.
PAGE 5
Step 4 Wave your hands in front of the sensor eye to activate. 1 foot a way (the indicator light of the sensor will flash once meaning the sensor was activated,and then the sensor will automatically reset after a few seconds ready for next trigger.) Step 5 Fix the back cover ( the back cover must be fixed well to ensure the waterproof if the sensor is installed outdoor).
PAGE 6
Step 6 Press “Melody” once to choose the melody for this sensor, total 35 optional melodies. Melody Step 7 Same operation if you have the additional sensor,and please refer to part 3 of the manuel for other settings. Step 8 Installation.
PAGE 7
Installation Notes: 1. Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind. 2.Please point the sensor towards a open field (not towards the trees or bushes). 3.please adjust the sensor a little down(never upwards). 4.please point the sensor eye towards to the engine or exhaust pipe if detecting vehicles.(the working principle of the senor is detecting the movements with heat sources).
PAGE 8
3. Other Settings (1)How to add additional sensors/receivers to the system (up to 32 sensors can be added to one or multiple receivers) Step 1 Plug the receiver into an outlet. Step 2 Press and hold the “Volume” button for 5 seconds and release the button when you hear a beep prompt and the indicator light flashes. light up Volume press and hold the Volume button for 5 seconds flashing slowly Volume release the button Step 3 Activate the sensor.
PAGE 9
flashing quickly 1 foot a way (the indicator light will flash once meaning the motion sensor was activated and sent the wireless signal) (a ring tone prompt and the indicator light flashes quickly meaning the sensor has been added to the plug-in receiver successfully) Step 4 Activate the sensor again to confirm the sensor has been added to the receiver already. Step 5 Press”Melody”button to choose the melody for this sensor. total 35 melodies optional.
PAGE 10
(3)How to adjust the alarm volume Step 1 Plug the receiver into an outlet. Step 2 Press the “Volume” once to adjust the volume of the receiver (total 4 adjustable volume levels). Volume (4)How to change the melody for the sensors (total 35 optional melodies; you can match different melody for each sensor.) Step 1 Plug the receiver into an outlet. Step 2 Activate the sensor first,and then press the “Melody” button to choose the melody for this sensor.
PAGE 11
Technical parameters Item Working Voltage Working Current Technical Parameters AC 110V-220V Static Current 20mA; Alarming Current 300mA Wireless Frequency 433MHz FSK+FHSS Wireless Motion Sensor 100mm 75mm 65mm 30mm Technical parameters Item Technical Parameters Detection Range Low sensitivity----35 feet(10m) High sensitivity----50 feet(15m) Detection Angle 15° Wireless Transmission Range 1/2 Mile (800m) 433MHz FSK+FHSS Wireless Frequency 4.5V Working Voltage 3pcs AA 1.