Instructions for use WASHING MACHINE Contents GB English,1 GB Installation, 2-3-4-5 AR , 15 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance, 6 Cutting off the water and electricity supplies Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips, 7 General safety Disposal RPD 104 7 Description o
Installation GB ! This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/ herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor; alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
GB As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or or coloured Green or Green & Yellow. Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board.
Technical data GB Model RPD 104 7 Dimensions width 59.5 cm height 85 cm depth 60,5 cm Capacity from 1 to 10 kg Electrical connections please refer to the technical data plate fixed to the machine maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 71 litres up to 1400 rotations per minute Water connections Spin speed Test Programmes according to SASO 2692.2007/2693.
Care and maintenance GB Cutting off the water and electricity supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. • Unplug the washing machine when cleaning it and during all maintenance work. Cleaning the washing machine • The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Precautions and tips ! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. GB General safety • This appliance was designed for domestic use only.
Description of the washing machine GB Control panel FUNCTION MULTI RINSE button buttons ON/OFF CLEANING ACTION button button DISPLAY Detergent dispenser drawer Programme Key WASH CYCLE SELECTOR KNOB START/PAUSE AUTO CLEAN button with indicator light KEY LOCK button button DELAY TIMER TEMPERATURE button button SPIN button Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
C Display C A GB H G C L M I B F D X Z E Y The display is useful when programming the machine and provides a great deal of information. The following will appear in area A: the icon and selected washing programme, the washing phases and time remaining to the end of the wash cycle. Area B will include the two intensity levels relative to the DIRECT INJECTION option. The indicator lights relative to the available functions appear in area C.
Running a wash cycle GB 1. SWITCH THE MACHINE ON. Press the On/Off button ; the text HOTPOINT will appear on the display and the START/PAUSE indicator light will flash slowly in a green colour. 2. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page. 3. MEASURE OUT THE DETERGENT.
Wash cycles and options Max. temp. (°C) Max. speed (rpm) Fabric softener Max. load (kg) Description of the wash cycle 40° 1400 6 Cycle duration GB Detergents Wash Wash cycles Table of programmes and wash cycles DAILY CLEAN Anti-Stain 2 Anti-Stain Quick 40° 1200 5 1400 10 3 Cotton: lightly soiled resistant and delicate colours. 40° (Max. 90°C) 4 Synthetics: lightly soiled resistant colours. 40° (Max.
Detergents and laundry GB Detergent dispenser drawer Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause a build up on the inside of your appliance and contribute to environmental pollution. ! Use powder detergent for white cotton garments, for pre-washing, and for washing at temperatures over 60°C. ! Follow the instructions given on the detergent packaging.
Troubleshooting Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. • The appliance is not plugged into the socket fully, or not enough to make contact. The wash cycle does not start. • • • • • The washing machine door is not closed properly.
Service GB Before contacting the Technical Assistance Service: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the wash cycle to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
تعليمات االستخدام ماكينة غسيل المحتويات عربي عربي، عربي التركيب19-18-17-16 ، إفراغ المحتويات وتحديد المستوى وصل إمدادات الكهرباء والماء دورة الغسيل األولى البيانات التقنية وصف ماكينة الغسيل21-20 ، لوحة التحكم شاشة العرض تشغيل دورة غسيل22 ، دورات الغسيل والخيارات23 ، جدول البرامج ودورات الغسيل خيارات الغسيل RPD 104 7 مواد التنظيف والغسيل24 ، درج وعاء مواد التنظيف تحضير الغسيل دورات الغسيل الخاصة وسائل حذر ونصائح25 ، الوقاية العامة
التثبيت عربي ! يجب االحتفاظ بدليل التعليمات هذا في مكان آمن لمراجعته في المستقبل .إذا تم بيع الجهاز ،إرساله أو نقله ،تأكد من أن دليل التعليمات قد أرفق بالماكينة بحيث يتمكن مالكوها الجدد من التعرف على عملها وخصائصها. تحديد مستوى الماكينة بشكل صحيح سيمنحها الثبات ،سيساعد على تحاشي االرتجاجات والضجيج الزائد وسيمنعها من االنحراف أثناء العمل .إذا تم وضعها في خزانة أو على بساط ،قم بمعايرة األرجل بنفس الطريقة لتوفير فسحة تهوئة كافية تحت ماكينة الغسيل.
مؤرضا. تحذير -يجب أن يكون هذا الجهاز ّ يجب تنفيذ العمليات التالية من قبل أخصائي كهرباء مؤهل. وصل خرطوم تصريف الماء قم بتوصيل خرطوم تصريف الماء، من دون ثنيه ،بأنبوب تصريف أو بتصريف جداري على ارتفاع يتراوح بين 65وحتى 100سم عن األرض؛ 65 - 100 cm عربي تبديل المصهر: عند تبديل مصهر معطوب ،من مصهر ASTA 13أمبير معتمد إلى BS 1362يجب أن يكون دائما مستخدما ،وإعادة مالءمة غالف المصهر .
عربي في حال لم تتوافق ألوان األسالك في التوصيل مع مفاتيح األلوان المعرفة في أطراف القابس لديك ،تصرف على النحو التالي: قم بتوصيل السلك األخضر واألصفر بالنهائية المشار إليها بـ Eأو باللون األخضر أو األخضر واألصفر. قم بتوصيل السلك البني بالنهائية المشار إليها بـ Lأو الملونة باللون األحمر. قم بتوصيل السلك األزرق بالنهائية المشار إليها بـ Nأو الملونة باللون األسود.
البيانات التقنية عربي الطراز RPD 104 7 األبعاد العرض 59.5سم االرتفاع 85سم العمق 60,5سم السعة من 1إلى 10كجم التوصيالت الكهربائية يُرجى الرجوع إلى لوحة البيانات المثبتة على الجهاز توصيالت المياه الحد األقصى للضغط 1ميجا باسكال ( 10بار) الحد األدنى للضغط 0.05ميجا باسكال ( 0.
وصف ماكينة الغسيل عربي لوحة التحكم زر MULTI زر RINSE CLEANING (الشطف المتعدد) ACTION أزرار FUNCTION زر (الوظيفة) (عملية التنظيف) ( ON/OFFتشغيل/إيقاف تشغيل) شاشة العرض زر START/PAUSE زر AUTO CLEAN (تشغيل/إيقاف مؤقت) مع مصباح إشارة (التنظيف التلقائي) زر KEY LOCK مفتاح البرنامج درج وعاء المنظف (قفل المفاتيح) زر TEMPERATURE زر DELAY TIMER (درجة الحرارة) (مؤقت التأخير) مقبض اختيار دورة الغسيل زر SPIN (
شاشة العرض ـ ـ عربي ـ ـ ـ ـ ـ كبيرا من المعلومات. قدرا ً الشاشة مفيدة للغاية عند برمجة الغسالة وتوفر ً سيظهر ما يلي في المنطقة أ :الرمز وبرنامج الغسيل المحدد ،ومراحل الغسيل والتجفيف والوقت المتبقي إلنهاء دورة الغسيل. ستضم المنطقة ب المستويين الخاصين بقوة الغسيل المتعلقين بخيار .DIRECT INJECTION تظهر مصابيح المؤشر المتعلقة بالوظائف المتاحة في المنطقة جـ. تضم المنطقة د الوقت المتبقي لبدء البرنامج المحدد في حالة تعيين وظيفة ( DELAY TIMERمؤقت التأخير).
تشغيل دورة غسيل عربي .1شغل الغسالة .اضغط على زر ( On/Offتشغيل/إيقاف تشغيل) ،سيظهر النص ARISTONعلى الشاشة ويومض مصباح المؤشر START/ ( PAUSEتشغيل/إيقاف مؤقت) ببطء باللون األخضر. .2ضع الغسيل في الغسالة .افتح باب الكوة .ثم ضع الغسيل ،وتأكد من أنك ال تتجاوز قيمة الحمولة القصوى المشار إليها في الجدول الخاص بالبرامج في الصفحة التالية. .3عاير كمية المنظف .افتح درج وعاء توزيع المنظف للخارج واسكب المنظف في الحجرات المناسبة كما هو موضح في "المنظفات والغسيل".
دورات الغسيل والخيارات جدول البرامج ودورات الغسيل دورات الغسيل 1 2 3 1400 1200 :المالبس المقاومة لالتساخ القليل والمالبس الرقيقة الملونة. 4 :المالبس ثابتة األلوان قليلة االتساخ. :لتنظيف المالبس قليلة االتساخ بسرعة (غير مناسب للمالبس الصوفية والحريرية والمالبس التي تتطلب الغسيل اليدوي). 6 7 >= (افتراضي) :للمالبس المصنوعة من الصوف والكشمير ،وما إلى ذلك.
مواد التنظيف والغسيل عربي درج وعاء المنظف تعتمد نتائج التنظيف الجيدة ً أيضا على الكمية المناسبة من المنظف: حيث إن إضافة كمية زائدة من المنظف لن تؤدي بالضرورة إلى غسيل أفضل بدرجة كبيرة ،ولكن قد يؤدي ذلك في الواقع إلى التراكم داخل الجهاز والمساهمة في تلوث البيئة. ! استخدم مسحوق التنظيف للمالبس القطنية ،وللغسيل األولي ،وللغسيل في درجات حرارة تتجاوز 60درجة مئوية. ! اتبع اإلرشادات الموضحة على عبوة المنظف.
وسائل حذر ونصائح ! تم تصميم ماكينة الغسيل وتصنيعه طبقا لمواصفات األمان العالمية. يتم تزويد التحذيرات التالية ألسباب وقائية ويجب قراءتها بعناية. عربي الوقاية العامة • • • • • • • • • • • • تم تصميم هذا الجهاز لالستخدام المنزلي فقط.
العناية والصيانة عربي قطع إمداد الماء والكهرباء العناية بباب وبرميل الجهاز لديك • قم بإقفال حنفية الماء بعد كل دورة غسيل .سيحد هذا من تآكل النظام الهيدروليكي داخل ماكينة الغسيل ويساعد على منع التسربات. • أترك باب الفتحة مفتوحا دائما لتحاشي تك ّون الروائح الكريهة. • افصل الماكينة عن الكهرباء عند تنظيفها أو أثناء أي عمل صيانة. تنظيف ماكينة الغسيل • يمكن تنظيف األجزاء الخارجية والقطع المطاطية في الماكينة باستخدام خرقة نظيفة مبللة بالماء الفاتر والصابون .
استكشاف المشاكل وحلها يمكن لماكينة الغسيل أن تفشل في العمل فجأة .قبل االتصال بخدمة المساعدة التقنية (أنظر "الخدمة") تأكد من أن المشكلة ال يمكن حلها بسهولة باستخدام الجدول التالي. المشكلة: األسباب المحتملة /الحلول: ال يمكن تشغيل ماكينة الغسيل. • الجهاز غير موصل بالمقبس الكهربائي بشكل كامل ،أو أنه غير موصل بشكل كاف ليحدث تماس. عربي • يوجد انقطاع كهرباء في البيت. دورة الغسيل ال تبدأ بالعمل. • • • • • باب ماكينة الغسيل غير مقفل بشكل صحيح.
الخدمة 11136177 07/2017 عربي قبل االتصال بخدمة المساعدة التقنية: • افحص فيما إذا كان بإمكانك حل المشكلة بنفسك (أنظر "استكشاف المشاكل وحلها"). • أعد تشغيل دورة الغسيل للفحص فيما إذا تم حل المشكلة. • إذا لم يحدث ذلك ،اتصل بمركز مساعدة تقنية معتمد. ! اطلب دائما مساعدة فنّي مؤهل. الرجاء خذ بعين االعتبار المعلومات التالية: • نوع المشكلة؛ • طراز الجهاز ().Mod؛ • الرقم التسلسلي (.