Instruction manual

ManualsBrandsHotpoint ManualsAppliancesIntegrated Dishwasher

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

PRODUCT DESCRIPTION

1. ON/OFF button

2. PREVIOUS button

3. NEXT button

4. Tablet Detergent (All-in-one) button

5. Zone Wash button

6. Zone Wash indicator light

7. Display

8. Eco program indicator light

9. Start Delay indicator light

10. Program number and remaining time indicator

11. Closed water tap indicator light

12. Rinse Aid rell indicator light

13. Salt rell indicator light

14. Tablet Detergent (All-in-one) indicator light

15. Zone Wash 3D button with indicator light

16. Short Time button with indicator light

17. Extra Dry button with indicator light

18. Start Delay button with indicator light

19. START button with indicator light

CONTROL PANEL

0000 000 00000

Service:

1. Upper rack

2. Cutlery rack

3. Foldable aps

4. Upper rack height adjuster

5. Upper spray arm

6. Lower rack

7. Space Zone support

8. Lower spray arm

9. Filter Assembly

10. Salt reservoir

11. Detergent and Rinse Aid dispensers

12. Rating plate

13. Control panel

5 6 7 8 9 10 12111

2 3 4

13 14 15 16 17 1918

INSTRUCTION FOR USE

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please register your appliance on:

www.hotpoint.eu/register

Summary of content (12 pages)

PAGE 1
EN INSTRUCTION FOR USE THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order to receive a more complete assistance, please register your appliance on: www.hotpoint.eu/register Before using the appliance carefully read Safety Instructions guide. PRODUCT DESCRIPTION APPLIANCE 7 8 9 3 10 4 5 11 Service: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
PAGE 2
FIRST TIME USE SETTING MENU AND SALT ADVICE REGARDING THE FIRST TIME USE After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack. 5. 6. 7. 8. Switch on the appliance by pressing the ON/OFF button. Switch off the appliance by pressing the ON/OFF button. Hold down START button for 5 seconds, until you hear a beep. The display shows the first available setting (letter „A”), followed by its value (for example: 3).
PAGE 3
EN FIRST TIME USE RINSE AID AND DETERGENT WATER SOFTENING SYSTEM FILLING THE DETERGENT DISPENSER Water softener automatically reduces water hardness, consequently preventing scale buildup on heater, contributing also to better cleaning efficiency. This system regenerates itself with salt, therefore it is required to refill salt container when empty. Frequency of regeneration depends on water hardness level setting regeneration takes place once per 6 Eco cycles with water hardness level set to 3.
PAGE 4
Program ActiveDry Drying phase PROGRAMS TABLE Available options *) Duration of wash program (h:min)**) Water consumption (litres/cycle) Energy consumption (kWh/cycle) P1 Eco 50° 3:20 9.5 0.64 P2 Auto Intensive 65° 2:00 - 3:10 14.0 - 17.0 1.50 - 1.85 P3 Auto Mixed 55° 1:30 - 2:30 14.5 - 16.0 1.15 - 1.30 P4 Auto Fast Wash 50° 0:55 - 1:20 13.0 - 14.5 1.15 - 1.25 P5 Delicates 45° 1:40 11.5 1.20 P6 Rapid 30’ 50° 0:30 9.0 0.50 P7 Good Night 50° 3:30 15.0 1.
PAGE 5
EN OPTIONS AND FUNCTIONS OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled. TABLET DETERGENT (All-in-one) This setting allows you to optimize the performance of the program according to the type of detergent used.
PAGE 6
LOADING THE RACKS CUTLERY RACK ADJUSTING THE HEIGHT OF THE UPPER RACK The third rack was designed to house the cutlery. Arrange the cutlery as shown in the figure. A separate arrangement of the cutlery makes collection easier after washing and improves washing and drying performance. Knives and other utensils with sharp edges must be positioned with the blades facing downwards. The geometry of the rack makes it possible to place such small items as coffee cups in the area in the middle.
PAGE 7
EN DAILY USE 1. CHECK WATER CONNECTION Check that the dishwasher is connected to the water supply and that the tap is open. 2. LOAD THE RACKS (see LOADING THE RACKS). The machine will switch off automatically during certain extended periods of inactivity, in order to minimise electricity consumption. If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the amount of detergent used accordingly. 3.
PAGE 8
CARE AND MAINTENANCE ATTENTION: Always unplug the appliance when cleaning it and when performing maintenance work. Do not use flammable liquids to clean the machine. CLEANING THE DISHWASHER Any marks on the inside of the appliance may be removed using a cloth dampened with water and a little vinegar. The external surfaces of the machine and the control panel can be cleaned using a non-abrasive cloth which has been dampened with water. Do not use solvents or abrasive products.
PAGE 9
EN INSTALLATION ATTENTION: If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. ELECTRICAL CONNECTION CONNECTING THE WATER SUPPLY Before inserting the plug into the electrical socket, make sure that: Adaptation of the water supply for installation should only be performed by a qualified technician.
PAGE 10
TROUBLESHOOTING In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance. PROBLEMS POSSIBLE CAUSES SOLUTIONS Salt indicator is lit Salt reservoir is empty.
PAGE 11
EN TROUBLESHOOTING PROBLEMS POSSIBLE CAUSES SOLUTIONS The dishes and glasses are blue streaked or have a bluish tinge. The rinse aid dosage is excessive. Adjust the dosage rates below. The salt level is too low. Fill the salt reservoir (see FILLING THE SALT RESERVOIR). The adjustment of the water hardness is not adequate. Increase the values (see WATER HARDNESS TABLE). The cap of the salt reservoir is not properly closed. Check to have properly closed the salt reservoir cap.
PAGE 12
400011521851 12/2020 as - Xerox Fabriano