INSTRUCTION FOR USE
EN THANK YOU FOR PURCHASING A HOTPOINT PRODUCT. To receive more comprehensive help and support, please register your product at: www.hotpoint.eu/register Before using the appliance carefully read Health and Safety guide. The control panel of this dishwasher activates pushing by ON/OFF button. For energy saving the control panel deactivates automatically after 10 minutes if no cycle has started. PRODUCT DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
EN FIRST TIME USE After connecting the appliance to the power supply for the first time, the display will guide you to set up the appliance for first use. Once done, proceed to the next step by pressing „OK” button. 1. The language selection LANGUAGE: ENGLISH? <> = CHANGE OK = YES To select preferred language please press button „<” or „>”. Confirm by pressing „OK” button. ENGLISH SELECTED After language confirmation, the appliance will go through the first time use configuration menu. 2.
EN 1. Open the dispenser B by pressing and pulling up the tab on the lid. 2. Carefully introduce the rinse aid as far as the maximum (110 ml) reference notch of the filling space A - avoid spilling it. If this happens, clean the spill immediately with a dry cloth. 3. Press the lid down until you hear a click to close it. 4. Confirm operation by pressing „OK” button. NEVER pour the rinse aid directly into the tub.
EN ADVICE AND TIPS TIPS Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand under running water. Arrange the crockery so that it is held in place firmly and does not tip over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing the water to reach every surface and flow freely.
EN LOWER RACK For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should ideally be placed at the sides to avoid interferences with the spray arm. A B The lower rack has tip-up supports which can be used in a vertical position when arranging plates or in a horizontal position (lower) to load pans and salad bowls easily.
EN SELECTING A CYCLE AND OPTIONS The list of available cycles and options can be found in Cycle Table on next page. Eco cycle is selected by default. If you want to have Last Used cycle selected by default, you can change it in „Settings Menu”. It is possible to select a cycle by pressing 1 of 6 cycles direct access buttons or by pressing „Extra Cycles” button repeatedly. When the last one is reached a further press goes back to the first.
EN ECO 50° EXTRA DRY, TABLET, START DELAY AUTO-INTENSIVE 3D ZONE WASH, ZONE WASH, TURBO, 65 ° EXTRA DRY, TABLET, START DELAY - AUTO-NORMAL 3D ZONE WASH, ZONE WASH, TURBO, 55° EXTRA DRY, TABLET, START DELAY AUTO-FAST 50° DELICATES 45° EXPRESS 30’ 50° Water consumption (l/cycle) Energy cosumption (kWh/cycle) 3:10 9.5 0.93 2:00 - 3:10 14.0 - 17.0 1.50 - 1.85 1:30 - 2:30 14.5 - 16.0 1.15 - 1.30 TABLET, START DELAY - 0:55 - 1:20 13.0 - 14.5 1.15 - 1.
EN OPTIONS AND SETTINGS With each cycle additional options can be used. A full list of available options working with specific cycles can be found in the Cycle Table on the previous page. All active options are shown on the display. To set an option press „OK” button. SET OPTIONS message is shown for a few seconds. Then use „<” or „>” button to navigate through the option list. Press „OK” to select the option, in the setting menu the LED above „OK” button is lit.
EN SETTINGS MENU To change machne settings you need to enter into the Settins Menu. Press „OK” button and navigate with „< , >” until SETTINGS is shown, then press „OK” button. To exit the setting menu, press any cycle button or press „< , >” button untill EXIT is shown, then press „OK” button. Language 1.LANGUAGE 1.ENGLISH ActivEco SET < > 1.ITALIAN To change language, enter in the setting menu by pressing „OK” button and navigate with „< , >” until „LANGUAGE” is shown, then press „OK” button.
EN CARE AND MAINTENANCE ATTENTION: Always unplug the appliance when cleaning it and when performing maintenance work.Do not use flammable liquids to clean the machine. CLEANING THE DISHWASHER Any marks on the inside of the appliance may be removed using a cloth dampened with water and a little vinegar. The external surfaces of the machine and the control panel can be cleaned using a non-abrasive cloth which has been dampened with water. Do not use solvents or abrasive products.
EN INSTALLATION ATTENTION: If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. ELECTRICAL CONNECTION WARNING: Under no circumstances should the water inlet hose be cut as it contains live electrical parts.
EN TROUBLESHOOTING Your dishwasher may not work properly. Before contacting the After-sales Service, check if the problem can be solved by going through the following list. PROBLEMS Display shows: CHECK SALT or ADD SALT POSSIBLE CAUSES SOLUTIONS Salt reservoir is empty. Refill reservoir with salt (see page 2). Adjust water hardness (see page 2). Rinse aid dispenser is empty. Refill dispenser with rinse aid (see page 2).
EN PROBLEMS POSSIBLE CAUSES SOLUTIONS The door doesn’t lock. Racks are not fit to the end. Verify that racks are fit to the end. The door is not lock. Vigorously push the door until you hear the “clack” sound. The dishes are rattling against each. Arrange the crockery correctly (see Loading the Racks). An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see Filling the Detergent Dispenser).
EN 15
EN PRODUCT FISCHE The technical data containing the energy consumption data can be downloaded from the website: docs.hotpoint.eu 400011317993B 03/2018 jk - Xerox Fabriano 16 CONTACTING AFTER-SALES SERVICE You can find our contact details in the warranty manual. When contacting our Client After-sales Service, please state the codes provided on your product’s rating plate.