Instructions for Installation and Use Built-in Coffee Maker Model HCM60 AMC-3
AMC-3
CONTENTS AMC-3 DESCRIPTION OF THE MACHINE ........................................................................................................ P. 4 • Front view .......................................................................................................................................... P. 4 • Side view and controls ........................................................................................................................ P. 5 • Safety instructions and warnings ......
DESCRIPTION OF THE MACHINE Front view 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26.
DESCRIPTION OF THE MACHINE Side view and controls Safety instructions and warnings This machine complies with the current safety regulations. Incorrect use of the machine may cause harm. Read the instructions carefully before using the machine. They contain important information on safety, use and maintenance, to provide protection and to avoid damaging the machine.
• Installation, maintenance and repair works must only be carried out by qualified persons. Any installation, maintenance and repair works carried out incorrectly may cause considerable danger to the user, for which the manufacturer will not assume any liability.
DESCRIPTION AND OPERATION The coffee machine has two heating systems, one for heating the water and one for the coffee. It is possible to prepare boiling water (for tea) or to use the steam (for cappuccino) and to prepare espresso coffee. Unlike most other machines, in this coffee machine, the beans can be ground just when they are required, allowing you to taste the aroma of freshly ground coffee at its best.
INSTALLATION OF THE MACHINE N.B. Owing to the weight of the machine, the cabinet must be secured firmly to the wall. 450 ±2 1. Check that the opening dimensions can accommodate the machine (Fig. 2A/B). n Mi 506 9 27 438 560 +6 458 ON/OFF 600 595 19 Fig.
INSTALLATION OF THE MACHINE Fig.
INSTALLATION OF THE MACHINE 2. Fix the 4 brackets A to the 4 corners of the cabinet opening, using the appropriate screws (Fig. 3). The horizontal movement of the nut allows any width tolerance of the cabinet to be offset. 3. Fix the 2 angular brackets B to the machine (Fig. 3). The 2 vertical holes on the brackets allow the height of the machine to be levelled and aligned. 4. Connect the machine to the electricity supply, observing the current safety regulations.
C ON/ OFF C Fig. 4 FILLING THE WATER TANK AND COFFEE BEAN HOLDER Filling the water tank The water tank should only be filled once it has been taken out of the machine. For a good espresso coffee, as well as using quality coffee, good water should also be used. It is therefore recommended that you empty the water tank frequently, preferably daily, and refill it with fresh water. Avoid leaving the water for too long time in the water tank. Boiling water or other liquids may damage the coffee machine.
OPERATIONAND USE Switch on Switch the machine on and off using the ON/OFF button Setting the grinding Certain factors indicate whether the degree of grinding has to be adjusted: • If the coffee comes out too quickly, this means that the beans have been ground too coarsely. • If the coffee comes out slowly, this means that the beans have been ground too finely. One very important factor for a good coffee is to set the degree of grinding correctly.
Setting the quantity of ground coffee to be supplied • Switch on the machine. • Start the grinding by holding the button down until the desired quantity is obtained. • This quantity will be memorised and remain the same for subsequent grindings. To return to the original setting: • Switch on the machine and switch it off by pressing the button for more than three seconds until the LED for the “grinding” button is illuminated. • Switch the machine on again.
PREPARATION OF THE DRINKS Preheating cups and pipes Espresso coffee should always be prepared with the pipes already heated and served in a hot cup that enhances the aroma and prolongs the flavour. Thermal shock can alter the aroma of coffee. The lower the quantity of espresso coffee in the cup, the more important it is to heat the cup. • Place the cup under the boiling water distributor. • Half-fill the cup. • Leave the water in the cup for 30 seconds and then empty it. This will preheat the pipes as well.
CARE AND CLEANING Allow the machine to cool down before cleaning it. Danger of scalding! Do not use steam appliances to clean it. Never use products containing soda, acid or chlorine, as these substances damage the surface of the machine. Regular cleaning guarantees the functioning and long life of your espresso coffee machine. Front and interior of the machine Take out the filter holder, tray and basin (Fig.
DESCALINGTHE MACHINE It is necessary to descale your machine at least once every 3 months based on the frequency of use and the hardness of the water. • Mix a suitable commercial descaler (observing the instructions indicated on the product) with around 1 litre of water and pour it into the water tank. • Switch on the machine. • Press the hot water button. • Empty around 1/3 of the contents of the water tank from the steam distributor and the filter holder, without coffee.
TECHNICAL DATA • • • • • • • • • • • • • External dimensions (mm): Height 458 x Width 595 x Depth 295 Built-in dimensions (mm): Height 450 x Width 568 x Depth 290 Operating voltage: 230 V – 50/60 Hz Pump pressure: 12 bar Pump power: 48 Watts Coffee heating power: 1000 Watts Steam heating power: 600 Watts Grinder power: 100 Watts Fuse: 16 Amp Water tank capacity: Approx. 2.5 litres Coffee tank capacity: Approx. 0.3 kg Coffee heating time: Approx. 2 mins Gross weight: 29.7 kg Net weight: 25.
After Sales Service “No company is better positioned to offer an after sales service on a Hotpoint appliance than us - the manufacturer” As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months. In addition to this you also have the advantage of free replacement parts for the first 5 years when fitted by a Hotpoint engineer.
Guarantee “Satisfaction guaranteed or your money back” We give you a unique ‘satisfaction guaranteed’ promise - valid for 90 days - after you have purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for an engineer to call. If the technical problem is not resolved under this guarantee, we will replace your machine or, if you prefer, give you your money back.
Key Contacts After Sales Service Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and services we offer. Repair Service and Information Desk UK: 08709 066 066 (Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays) www.theservicecentre.co.
