User Manual www.hotpoint.
EN Quick guide THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order to receive a more complete assistance, please register your appliance on www.hotpoint.eu/register Before using the appliance carefully read the Safety Instruction. Before using the machine, it is imperative that the transport bolts are removed. For more detailed instructions on how to remove them, see the Installation Guide.
PROGRAMMES Follow the instructions on the symbols of the garment’s wash care label. The value indicated in the symbol is the maximum recommended temperature for washing the garment. Anti Stain 100 This cycle is suitable to heavily-soiled garments with resistant colours. It ensures a washing class that is higher than the standard class (A class). When running the programme, do not mix garments of different colours. We recommend the use of powder detergent.
Quick guide KEY LOCK To lock the control panel, press and hold the “Energy saver” button for approximately 3 seconds. The symbol will light up on the display to indicate that the control panel has been locked (with the exception of the “ON/OFF“ button). This prevents unintentional changes to programmes, especially with children near the machine. To unlock the control panel, press and hold the “Energy saver” button for approximately 3 seconds .
TROUBLESHOOTING The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended to check to see if the problem can be easily resolved using the following list. Anomalies: Possible causes / Solution: The washing machine does not turn on. • • The plug is not inserted into the electrical outlet, or not enough to make contact. There has been a power failure. The wash cycle does not start. • • • • • The door is not fully closed.
CLEANING & MAINTENANCE For any cleaning and maintenance, switch off and unplug the washing machine. Do not use flammable fluids to clean the washing machine. CLEANING THE OUTSIDE OF THE WASHING MACHINE Use a soft damp cloth to clean the outer parts of the washing machine. Do not use glass or general purpose cleaners, scouring powder or similar to clean the control panel – these substances might damage the printing. CHECKING THE WATER SUPPLY HOSE Check the inlet hose regularly for brittleness and cracks.
CLEANING THE DETERGENT DISPENSER Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently. 1 2 CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER Switch off and unplug the washing machine before cleaning the water filter or draining residual water. If you used a hot wash programme, wait until the water has cooled down before draining any water.
TRANSPORT AND HANDLING Never lift the washing machine by holding it at the worktop. 1. Pull out the mains plug, and close the water tap. 2. Make sure that door and detergent dispenser are properly closed. 3. Disconnect the inlet hose from the water tap, and remove the drain hose from your draining point. Remove all rest water from the hoses, and fix them so that they cannot get damaged during transport. 4. Refit the transport bolts.
10 mm - 0,39 inch 3. 2. 1. 150 ml 100 ml 50 ml 4. 2 cm - 0,7 inch 6. 5. 7.
8. 9. max 0,5 cm max 0,2 inch 10. 11. 12. max 100 cm 39 inch min 65 cm 25 inch max 100 cm 39 inch min 65 cm 25 inch max 100 cm 39 inch min 65 cm 25 inch 13. 14.
SAFETY INSTRUCTIONS Before using the appliance, read these safety instructions. Keep them nearby for future reference. These instructions and the appliance itself provide important safety warnings, to be observed at all times. The manufacturer declines any liability for failure to observe these safety instructions, for inappropriate use of the appliance or incorrect setting of controls. Very young children (0-3 years) should be kept away from the appliance.
ELECTRICAL WARNINGS It must be possible to disconnect the appliance from the power supply by unplugging it if plug is accessible, or by a multi-pole switch installed upstream of the socket in accordance with the wiring rules and the appliance must be earthed in conformity with national electrical safety standards. Do not use extension leads, multiple sockets or adapters. The electrical components must not be accessible to the user after installation. Do not use the appliance when you are wet or barefoot.
INSTRUCTIONS FOR THE FITTER Door Mounting Accessories (Fig. 1-2-3-4-5). Mounting the wooden panel onto the door and inserting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. The packaging was designed to make it possible to mount the wooden panel onto the machine without removing it completely (see figures below).
Using the Drilling Template. - To trace the positions of the holes on the lefthand side of the panel, align the drilling template to the top left side of the panel using the lines traced on the extremities as a reference. - To trace the positions of the holes on the righthand side of the panel, align the drilling template to the top right side of the panel. - Use an appropriately sized router to mill the holes for the two hinges, the rubber plug and the magnet.