Troubleshooting Guide

0-9 channel number
Set the channel for each intercom. The default channel is
#1. Set the channel by pressing and holding one of the
channel buons（1 thru 9 and 0) for 3 seconds, unl you
hear the Beep
and the channel buon lights. Set channels
on addional intercoms using the same steps. Intercoms
may be set to the same or different channel numbers
depending on intended use.
Volume Adjustment (VOL+/VOL-)
Press "VOL -" or "VOL +" to decrease or increase the volume
level. A tone will sound when you have reached the maximum
or minimum limit.
Note: To choose different ring tones
Step 1. Press and hold the "VOL +" and then press the
"VOL-" to enter the ring tone select mode .
Step 2. Press "VOL +" or "VOL -" to choose the ring tone
you like. There are 4 kinds of tones for you to choose.
Step 3. Press the "VOL +" and "VOL -" buons simultaneously
to exit ring tone setup mode.
SETTING CHANNEL
Please set different channel for different devices by
following steps :
1). Use the AC adapter to plug the intercom into a power outlet.
2). Set the channel for each intercom. The default channel
is #1. Set the channel by pressing and holding one of the
channel buons（1 thru 9 and 0) for 3 seconds, unl you
hear the Beep and the channel buon lights. Set channels
on addional intercoms using the same steps. Intercoms
may be set to the same or different channel numbers
depending on intended use.
3). Please keep digital code consistent in seng channels,
for example: all equipment uses code A, and please record
the channel code of each office/room, to enable you to
rapidly and accurately call others.
USING ADDITIONAL STATIONS
You may add addional staons to the system as long as
they transmit on the same frequency.
OPERATION
Receive a Call
A device will emit a series of rings when receiving a call
from another device. Press and hold the TALK buon to
answer the call, and speak 30-40 cm toward the MIC in a
normal voice. The blue LED indicates that Talk mode is
acve. Release the TALK buon to listen for a reply. All
devices set to the same channel will receive the
transmission.
Make a Call
Select the desired channel by pressing and releasing a
channel buon, then press CALL. This will ring all devices
set to that channel. Connue the conversaon as described
in “Receive a call”.
Notes:
• You will not be able to hear a transmission from another
device while you are pressing the TALK buon.
• When talk ends, the channel of calling unit automacally
change to the originally set channel aer 1 minute.
Troubleshoong UNNECESSARY WHITE NOISE FROM NEAR
BY DEVICES:(CTCSS)
A/B/C Code:
If receving unnecessary noise on seng A or C code. You
may switch your intercom system (all unites) seng to B
or C code.
Note:
Monitor Fucon- For connuous talk or room monitoring
which can last up to 24 hours.
FRS Frequencies
Limited 12 months Warranty
EXCEPT AS PROVIDED HEREIN, SELLER MAKES NO EXPRESS
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN, EXCEPT AS PROVIDED HEREIN, SELLER
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER
OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY
BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING,
BUT NOT LIMITED TO ANY DAMAGES RESULTING FROM
INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE,
OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,OR
CONSEQUENTIAL DAMAGES,EVEN IF SELLER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
In the event of a product defect during the warranty period,
contact the Seller to obtain an RBM#, and then return the
product, along with the sales receipt as proof of purchase
date, to Seller. The Seller will, at its opon either correct
the defect by product repair without charge for parts and
labor; replace the product with one of the same or similar
design or refund the purchase price.
All replaced parts and products and refunded products
become the property of the Seller. New or recondioned
parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products
are warranted for the remainder of the original warranty
period. You will be charged for repairs on products no
longer covered by warranty.
For all returns, please write down the RBM# and return
date on the outside of the package. This will speed up
the process of handling your return and issuing a refund
or providing you with a replacement. Refunds are not
issued for products no longer covered by warranty. The
warranty will not cover replacements in cases where
damage or failure is caused by, or aributable to:
(a) acts of God, abuse, accident, misuse, improper abnormal
usage, failure to follow instrucons, improper installaon
or maintenance, alteraon, lightning or other instance of
excess voltage or current,
(b) any repairs other than those provided by the Seller,
(c) consumables such as fuses or baeries,
(d) cosmec damage,
(e) transportaon, shipping or insurance costs,
(f) or costs of product removal, installaon, set-up, service
adjustment or reinstallaon.
Our goal is for you to have the best possible experience
with Hosmart. We appreciate receiving comments on any
aspect of your experience with Hosmart or our products.
Please contact us with any problems, prior to leaving any
online feedback, so that we may address your concern.
We guarantee your complete sasfacon for this transacon.
Please note that our office hours are 9:00 am to 5:00 pm
(GMT+8) Monday through Friday. Offices are closed
Saturday, Sunday and public holidays. We apologize for any
late replies during holidays.
This product produced by:
Macross Microelectronics (HK) LIMIT
FLAT/RM KY001 UNIT 3 27/F HO KING COMM CENTRE
NO.2-16FA YEEN STREET MONGKOK KL
CAUTIONS
The following will help you maintain your wireless intercom
for years to come.
* Keep staons from geng wet. It is not waterproof.
* Keep staons in a control environment. No extreme
temperatures.
* Handle the staons with care. No dropping, throwing
or roughness.
* Keep staons clean from dust and dirt for this can damage
the circuit board.
* Do not use chemicals or cleaning solvent. Simple use a
damp cloth to clean the staon.
* Modifying or tampering with the staons internal
components can cause it to malfucon as well as null
or your warranty.
* If your product is not working as adversed then return
it to local retailer for assistance or contact us at our
e-mail.
THE FCC WANTS YOU TO KNOW
Your intercom may cause TV or radio interference. To be certain
turn off your intercom and check your TV or radio on
its performance. If sll receiving interference, rest a
sure it is not your intercom. You may try to eliminate
interference by:
* Moving your staons further away from the receiver.
* Moving your staons further away from your TV or radio.
If these opons do not solve your problem the FCC requires
you to stop using your intercom. Change or modificaons
not approved by the party responsible for compliance
coud void the user authority to operate the equipment.
Channel
Code
Device
Locaon
2
A
General
Manager Room
3
A
Financial
Department
4
A
HR
Department
5
A
Sales
Department
A B CDC 5V
A B CDC 5V
7 467.7125
8 462.5500
9 462.5750
If you have any questions with the unit, please contact us by
navigating to www.myhosmart.com, then click Warranty, and fill
out the form, we will assist you as quickly as possible.
E-mail: [e-mail]
Phone: [phone]
If you have any questions with the unit, please contact us by
navigating to www.myhosmart.com, then click Warranty, and fill
out the form, we will assist you as quickly as possible.
E-mail: [e-mail]
Phone: [phone]
– This radio is designed for and classified as “General population/uncontrolled Use”
– DO NOT operate the radio without a proper antenna attached, as this may damage the radio
and may also cause you to exceed RF exposure limits. A proper antenna is the antenna
supplied with this radio by the manufacturer or an antenna specifically authorized by the
manufacturer for use with this radio, and the antenna gain shall not exceed 2dBi by the
manufacturer declared.
– DO NOT transmit for more than 50% of total radio use time, more than 50% of the time can
cause RF exposure compliance requirements to be exceeded.
– During operation, the separation distance between user and the antenna shall be at least
20cm, this separation distance will ensure that there is sufficient distance from a properly
installed externally-mounted antenna to satisfy the RF exposure requirements
– During transmissions, your radio generates RF energy that can possibly cause interference
with other devices or systems. To avoid such interference, turn off the radio in areas where
signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to
electromagnetic radiation such as hospitals, aircraft, and blasting sites.
FEATURES
ANT(antenna)
Receiving and eming FM wireless signal.
MIC
Talk to MIC 30-40cm away from it with normal volume.
DIGITAL CODE(A/B/C)
It can reduce external interference by changing different
digital code.
Note: CODE key is on the back of device and beside power port.
CALL
To make a call, select the channel you want to communicate
with and press “CALL”.
TALK
Press and hold "TALK" when speaking. Release "TALK" to
listen for a response. The indicator becomes OFF, the voice
informaon is be sent out.
MONITOR
Pressing “MONITOR” puts the unit in monitor mode, and
the unit will be monitored by other units, that have been
set to the same code and channel, for 24 hours. Press any
key to exit monitor mode.
GROUP (Group-Call Funcon)
Press and hold “GROUP” to talk to all intercoms simultaneously,
even the device in different channel code.
Hosmart was founded in 2012 by a former group of Motorola
engineers and designers. Now fast forward a few years and
we are now the industries leader in home intercom and
security products.
Our vision is to become the world leader in home intercom
products and soluons. We design as well as engineer
intelligent home intercom systems. We want to be your
homes soluon. Our company philosophy is to focus our
efforts and energy based on our client's wishes.
We are confident that you will enjoy and be sasfied with
our products. Any damage or malfuncon of Hosmart
product is 100% guaranteed to be replaced.
If you have any questions with the unit, please contact us by
navigating to www.myhosmart.com, then click Warranty, and fill
out the form, we will assist you as quickly as possible.
E-mail: [e-mail]
Phone: [phone]
FCC SATEMENT
FCC ID: FCC ID: 2AJEM-HY810
Power: DC 5V 1000 mA Input: 100-240V Output: 5V
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICEMUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
OVERVIEW
The intercom has a range of 1/2 mile and is able to
simultaneously funcon mulple conversaon using a
462Mhz secure digital radio link. The intercom is a half
duplex TDD FM transceiver that it can only work alternately
in the transming or receiving state.
10-CHANNEL
WIRELESS INTERCOM
MODEL:HY-810
1 2 3
4 5 6
7 8 9
VOL-
MONITOR GROUP
TALK
CALL
0
VOL+
Volume Control
Funcon buon
Speaker
Channel select buon
MIC
Antenna
A B CDC 5V
Digital Code Switch(A/B/C)
AC Adapter
If the walls are too thick or if the building
is mental causing no signal to pass through?
-Press and hold down TALK to communicate
aer other unit finished talk.
- Are the intercoms too close causing Audio
feedback？
-Change locaon by using Power Bank, moving
to other locaons for beer recepon and
transmission.
-Keep intercom away from metal objects and
electrical wiring.
-If the intercom is set in Monitor Mode.
-You will not be able to hear a transmission from
another device while you are pressing the TALK
buon.
Can not talk to other
intercom
Intercom is not geng expected
transmission range
-The intercoms are too close to each other.A
cordless phone,cell phone or other radio devices
can also cause stac.
Stac and feedback is heard
in intercom
正面
背面
成型尺寸：105*148mm