ATM300 [ User manual ] User Manual The ReFLEX Module (ATM 300) ReFLEX Module 0/13 Tel 02 ) 2659 - 7345 Fax 02 ) 3662 - 0973 http://www.hstelnet.
ATM300 [ User manual ] Content 1. Description 2. Outline and Function 2.1 Outline 2.2 Description of 14 pin Connector 2.3 Sub Board & Data Link Cable 2.4 Package 3. Configure the ReFLEX Module – PPS 3.1 login 3.2 List 3.3 Control 4. Message receiving and sending 4.1 HSM8800 4.1.1 Message sending 4.1.2 Message receiving HOW TO SET “ReFLEX” TWO WAY RADIO MODULE. ReFLEX Module 1/13 Tel 02 ) 2659 - 7345 Fax 02 ) 3662 - 0973 http://www.hstelnet.
ATM300 [ User manual ] 1. Description - System Block Diagram ReFLEX Module System Host Device ReFLEX CLP Serial Interface Carrier’s System < Figure 1> ReFLEX system Block Diagram - ReFLEX : The communication protocol between Carrier’s system and ReFLEX device or module through ReFLEX network. - CLP Serial Interface : It is communication Linking Protocol (CLP), it enable the wire communication between ReFLEx device or module and Host device through the Serial Interface.
ATM300 [ User manual ] 2. Outline and Function 2.1 ReFLEX Module Outline < Figure 2 > ReFLEX Module The interface between ReFLEX Module and Host Device will be done by 14 pin connector. 2.2 Description of 14 pin connector 1 8 2 9 3 10 4 11 5 12 6 13 7 14 < Figure 3 > 14 pin connector ReFLEX Module 3/13 Tel 02 ) 2659 - 7345 Fax 02 ) 3662 - 0973 http://www.hstelnet.
ATM300 [ User manual ] 2.
ATM300 [ User manual ] 1) Sub Board : The sub board will supply the power to module and it will be used for parameter setting (PPS) and data receiving and sending by PC. If you apply the DC 4-10V to power terminal, then module will be activated. The communication with PC will be able to by specific data link cable which supplied by module supplier. < Figure 5 > Data Link Cable 2) Data Link Cable : It will be used for communication between ReFLEX Module and PC through Sub Board.
ATM300 [ User manual ] 2.5 Package < Figure 6 > Package ● Pre caution for Module(ATM 300) interface The serial communication default speed is being set as 9600BPS, if you can change it CLP command. - Module (ATM 300) has a power save mode function, then you must wake up the module whenever you are to use it. The wake up time is 20ms, and if you are to wake up the module, send the CLP command 0x19.
ATM300 [ User manual ] 3. Configure the ReFLEX Module – PPS Please refer to PPS manual for more details. 3.1 Login < Figure 7 > Login Key in the default password ‘HSTMAST’. ReFLEX Module 7/13 Tel 02 ) 2659 - 7345 Fax 02 ) 3662 - 0973 http://www.hstelnet.
ATM300 [ User manual ] 3.2 List < Figure 8 > List - Global Scan List : Rx frequency setting(if Space is set Spacing is 10KHz) - IS Address : Information Service address - SPID : Service Provide ID - Personal Address : Cap code - Else : refer to PPS user’s guide - Menu Description ① Export : Store the PPS Parameter file. ② Import : Reading the PPS Parameter file. ③ Download : Download the data to ReFLEX Module. ④ Personal Address : Put in the ReFLEX Module MSN.
ATM300 [ User manual ] 3.3 Control < Figure 9 > Control - Power Level(mW) : RF Power Output - PPS password : PPS login password ReFLEX Module 9/13 Tel 02 ) 2659 - 7345 Fax 02 ) 3662 - 0973 http://www.hstelnet.
ATM300 [ User manual ] 4. Message Sending and Receiving If there is no Host device, you can send and receive the message through PC. The firmware, HSM8800 make you to sending and receiving the message, and you can also check the functionality of ATM300. 4.1 HSM8800 < Figure 10 > HSM8800 CLP Communicator v1.3 ReFLEX Module 10/13 Tel 02 ) 2659 - 7345 Fax 02 ) 3662 - 0973 http://www.hstelnet.
ATM300 [ User manual ] 4.1.1 Message Sending Sending the message to destination.. < Figure 11 > BMO Message Send ① Address Type : There are two(2) address type “P” and “E” Address Type P E Description Send the message using PIN number of ReFLEX Module. (Ex. : 3071297 ) Sending the message using email address. ( Ex. : hjino5@hoseo.or.kr ) < Table2 > Address Type ② Address : key in the address of receiving part. ③ ReFLEX Test Message: key in the sending message.
ATM300 [ User manual ] HOW TO SET ReFLEX TWO WAY RADIO MODULE. - Check the power source , 4~10V and 3A - Soldering the Shield Case to Ground - Connect the 50 ohm antenna to SMA connector of module *Do not operate the module without Antenna - Apply the power and Interface *Remark - Do not change the trimmer set on case - Do not open the shield case, In this case a warranty conditions will be invalid. “CAUTION : Exposure to Radio Frequency Radiation.
