Installation Instructions

1. Power supply mode

After installing the battery, the backlight lights up in red, and the red light in the box lights up at

the same time. If there is no operation within 10 seconds, the two lights will be off at the same

time.

After the light is off, all operations (including entering the password and changing the

password/RFID) are suspended, and need to be restarted after activation.

After the light is off, pressing any button will light up the backlight and the red light in the cabinet

again.

2. set password

Step 1: Use the emergency key to open the box

Step 2: Press the reset button once, the backlight flashes red once (0.5 seconds), the buzzer

beeps once (0.5 seconds), and the internal lighting red light flashes (until the registration status is

exited). (Red light for non-low voltage, yellow light for low voltage)

Step 3: Enter the password (4-6 digits) within 6 seconds and press the reset button once:

If the password is matched correctly, the backlight is turned off twice (0.5 seconds each time, 0.5

seconds interval), and 2 beeps (0.5 seconds each time, 0.5 seconds interval), the password

setting is successful. (Red light for non-low voltage, yellow light for low voltage)

If the password exceeds 6 digits or is less than 4 digits, 3 buzzers (0.05 seconds each time, 0.05

seconds interval) will beep quickly, and the password setting fails, restart from step 2.

It enters sleep without any action within 6 seconds.

Note: Registering a new password will overwrite the old password.

3. Set up RFID

Step 1: Use the emergency key to open the box

Step 2: Press the reset button once, the backlight flashes red once (0.5 seconds), and the buzzer

beeps once (0.5 seconds); the internal lighting red light flashes (until the registration status is

exited). (Red light for non-low voltage, yellow light for low voltage)

Step 3: Register an RFID within 6 seconds:

The backlight is turned off twice (0.5 seconds each time, 0.5 seconds interval), 2 buzzers (0.5

seconds each time, 0.5 seconds interval), RFID registration is successful. (Red light for non-low

voltage, yellow light for low voltage)

3 beeps (0.05 seconds each time, 0.05 seconds interval), RFID registration fails (including

configured and configured full), restart from step 2.

It enters sleep without any action within 6 seconds.

Note: Each device can store 5 groups of RFID. After the 5 groups have been stored, the 5 groups

of RFID that have been registered before need to be cleared.

three. Reset RFID

Clear RFID operation: press the reset button for 3 seconds (without any feedback in the first

PAGE 1
. Power supply mode Powered by 2 AA batteries After installing the battery, the backlight lights up in red, and the red light in the box lights up at the same time. If there is no operation within 10 seconds, the two lights will be off at the same time. After the light is off, all operations (including entering the password and changing the password/RFID) are suspended, and need to be restarted after activation.
PAGE 2
second), the backlight will be red for 6 seconds, and the internal lighting will flash red (until the registration status is exited) (red light for non-low voltage, yellow light for low voltage) ). Within this time range, press the reset button once again, and the backlight will turn off 3 times (lights off for 0.25 seconds each time, with an interval of 0.25 seconds). Beep once for 2 seconds. (Red light for non-low voltage, yellow light for low voltage) 4.
PAGE 3
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.