Quick Start Guide

Welcome to the Horizon DG10
Horizon DG10 dongle provides LTE service in a
small form factor. With diversified self-developed
LTE embedded mini-PCIE modules integrated,
Horizon DG10 dongle supports multi-band for
most operator’s bands and Private LTE, even
support special bands.
Horizon DG10
Quick Start Guide
Device Architecture
2
3
1
1
LTE antenna USB interface
2 3
LED
Working Environment
Power
Consumption
Operating
System
＜ 2.5W
Windows (Win7/Win8/Win10)
Mac (Mac OS 10.10 or above)
Linux
Chrome OS
Operating
Temperature
Storage
Temperature
Humidity
-10℃ ~ 45℃
-40℃ ~ 70℃
5% ~ 95% (Non-condensing)
Hardware Configuration
Remove the cover of the dongle.
Insert the SIM card into the SIM
slot on the side and put it in the right
position.
Re-attach the cover.
Step1
Step2
Step3
Install SIM Card
Connect and Turn on the USB Dongle
1. Make sure the
dongle is connected
to a USB port.
2. Unfold the antenna.
Connect to the Network
It takes several seconds to connect to the
LTE network. The sequence of different LED
status is as follows.
1. LED indicator starts with a red light.
2. Then LED indicator becomes blinking
green.
3. When connected successfully, LED
shows static green.
Login to the Web Management Page
Launch the web browser, enter
http://192.168.0.1 in the address bar, and
press Enter.
Software Configuration
Step1
Enter the username and password,
and click Login.
Step2
Step3
After the password is verified, you
can login to the web management page.
The default username and password are
both admin. If you want to view or configure
the dongle, you should use the super
account to log in to the web management
page. The default super username is
superadmin, and the password is admin.
LTE Settings
Choose Network > LTE Settings.
On LTE Settings page, you can
set the configuration of the LTE network.
In the Status list, you can view the
LTE status, such as Frequency, RSSI, RSRP,
RSRQ, CINR, SINR, Cell ID and etc.
Step1
Step2
Step3
The POWER indicator does not turn on.
Make sure the dongle is connected
properly to a USB port.
Make sure the output power of the
USB port is compatible with the dongle.
Try to unplug, then plug the dongle
into the USB port again or into a different
USB port.
If the problem persists, please contact
the authorized local service suppliers.
Fails to Login the web management page.
Make sure that the dongle is powered
on.
If the problem persists, please contact
the authorized local service suppliers.
The dongle fails to search for the wireless
network.
FAQs
Check if the antenna is open and not
folded.
Check if the indicator light is static green.
Check if the dongle is placed in an open
area.
If the problem persists, please contact
the authorized local service suppliers.
The parameters are restored to default
values.
If the dongle is powered off unexpectedly
while being configured, the parameters may be
restored to the default settings.
After configuring the parameters, down-
load the configuration file and restore the desi-
red settings quickly.
The dongle does not support SIM card
hot-plug, please confirm that the device is
powered off when the SIM card is inserted
or removed.
1 2 3 4
5
6
7 8 9
10 11 12
FCC Statement
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the
equipment and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement
installed and operated in accordance with
provided instructions and the antenna(s) used
for this transmitter must be installed to
provide a separation distance of at least 5mm
from all persons
and must not be co-located or operating in
conjunction with any other antenna or
transmitter. End-users and installers must be
provided with antenna installation
instructions and consider removing the
no-collocation statement.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Caution!
Any changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment.
The device has been tested and comply with FCC SAR limits.
The device has been tested and comply with
FCC SAR limits.
This equipment must be