HOOVER y son marcas registradas THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 3-98 C1498 HOOVER and are registered trademarks THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 Litho USA 56711-148
11
10
HOOVER Owner’s Manual Lightweight Commercial Cleaner English, Spanish Record and retain Model ____________ Serial No.
37 1 8 3 2 4 11 7 5 12 6 9 10 37 Use this illustration for agitator reassembly, if necessary. Washer must be placed between agitator ends and bearing. 1. Brush roll core 2. Flat sided projection 3. End plate 4. Bearing 5. Washer 6. Agitator end 7. Shaft 8. End section 9. Agitator end 10. Washer 11. Bearing 12. End plate 13. Round projection Lubrication Servicing of double-insulated appliances The motor is equipped with bearings which contain sufficient lubrication for the life of the motor.
32 The agitator 33 Disconnect cleaner from electrical outlet before checking or replacing brushes. What to buy A When purchsing a new brush roll (assembly complete), ask for HOOVER part No. 48414040. When replacing brush roll core only, ask for HOOVER part No. 4841048. Stretch new belt onto motor pulley (A). Extra effort may be required to stretch belt onto pulley.
The belt 26 25 What to buy D Use only genuine HOOVER belt, part No. 38528-027 with your cleaner. A A When to replace C B Disconnect cleaner from electrical outlet. To check belt, remove bottom plate and hood as shown in “How to replace belt.” Replace belt if it is stretched, cut or broken. How to replace Disconnect cleaner from electrical outlet. agitator and broken 26 Remove agitator belt. handle in lowest position. 25 Place Turn cleaner over and remove the two bottom plate screws (A).
19 18 20 A B A Carpet height adjustment 18 21 The cleaning of carpet and rugs takes place at the nozzle (A). (A) (B) (1) (2) (3) If it is necessary to raise and lower the nozzle for various carpet pile heights, slide the nozzle control knob to the desired setting. 19 20 For ease in sliding knob, the handle should be in the upright position (A). The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position (B).
14 13 15 B C D A Place nut (A) in recessed area at back of handle. Hold nut in place while tightening bolt securely with a screwdriver. Note: Only one nut is needed on this model. The extra nut is not required but has been provided for your convenience. On upper front handle, grasp bag clip (B) and pull down firmly. Hook bag clip into slot in bag cap. STEP 6 Attach paper bag CAUTION: When the cleaner is turned ON, the agitator continues to rotate while the handle is in the upright position.
4 H 5 F I F I H J 4 Rotate cord protector (F) on cord until you see its arrow (H). K F With arrow (H) on (F) pointing toward arrow (H) on (I), press groove (J) into slot (K). Pull cord tight. 5 STEP 4 Attach cloth outer bag 6 7 F 6 Press cord into place at each of the three notches indicated and note correct positioning of (F). C B Do not plug cleaner in until assembly is totally complete.
Assembling cleaner It is extremely important to read and follow all instruction steps in order. STEP1 Unpack carton 1 F A B C D Remove all parts from carton and identify each item shown. Make sure all parts, especially small items, such as G, are located before disposing of cardboard packing. 1 E G A. Upper handle B. Lower handle C. Cord D. Outer bag F. Cleaner body G.Handle bolt and nut packet (one extra nut included) H.
HOOVER Owner’s Manual English, Spanish Lightweight Commercial Cleaner Record and retain Model ____________ Serial No. _______________ (located on bottom of cleaner) Important Safeguards! When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning: • • Review this manual before operating cleaner • • • Index • Assembling Cleaner......................... 2-4 Cleaner Descriptions ..........................