USER MANUAL HN-GB200ESL 1080P AHD/CVI/TVI/1200TVL Varifocal Outdoor Camera
Important Notes If there is ANY QUESTION of the camera, please contact us, EACH camera has been tested before shipping. Service@honictech.com 1. Power supply, coaxial video cable and DVR are NOT INCLUDED but REQUIRED. 2. Default mode: 1080P AHD video format. 3. Power on the camera, then switch to the corresponding video format that your DVR support. 4. 1080P HD modes (TVI, AHD, CVI) DO NOT compatible with 720P or 960P DVR. 5. At least DC 12V 2A power adapter is required.
Notice Before Using Default Mode: 1080P AHD Video Output. If your DVR is TVI, CVI or Analog DVR, please take the OSD cap off and switch the OSD joystick to the corresponding video mode. POWER ON the camera, switch the OSD joystick in 10 seconds: LEFT Push 5s to 1200TVL mode for analog DVR. RIGHT Push 5s to TVI mode for 1080P TVI DVR or XVR. DOWN Push 5s to CVI mode for 1080P CVR or XVR. UP Push 5s to AHD mode for 1080P (N) AHD DVR or XVR. Note: 5s means 5 seconds Installation and Operation: 1.
1x user manual 1x drill template 1x Allen wrench 2. Mechanical Inspection Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is clean, and no connectors are broken, damaged, or loose. If equipment appears to be damaged or defective please contact us for assistance. 3. Special Attention (i) The installer must comply with electrical safety standards.
temperature must match requirement of this equipment. (vii) The camera is a low voltage product. If installed outdoors, proper safety and lightening grounding are required. 4. Wiring Connections (i) Connect the power supply's DC plug to the camera's power outlet. (ii) Connect the camera to the DVR with a 75Ω coaxial video cable. (iii) Connect power supply's AC plug to a suitable AC power outlet. (iv) Adjust the lens direction according to the required surveillance area and environment.
5. Adjusting Zoom and Focus This cameras will come from the factory set for the wide field of view, meaning that it has the low magnification. Turn the Zoom screw (near the lens) anticlockwise to increase the magnification and then adjust the Focus until the image is clear. Note: The focus knob is very sensitive, so we suggest you adjust zoom knob to the position you need, then adjust focus knob to make it almost clear, then adjust zoom knob again to make it 100% clear.
2. Using a smartphone running the appropriate mobile monitoring app to view the camera. 3. Use of an LCD camera tester which temporarily connects to the video. 6. Camera Lens Angle 1/3"CMOS 1/3"CMOS Left/Right Up/Down 2.8mm 89.9° 79.8° 3.6mm 75.7° 66° 4mm 69.9° 60.7° 6mm 50.0° 42.6° 8mm 38.5° 32.6° 12mm 26.2° 22.1° Lens(mm) 7. Detailed Lens Chart Detailed Lens Chart 5 feet 10 feet 25 feet 2.8mm 6.4 * 8.6 12.9 * 17.1 32.1 * 42.9 4.0mm 4.5 * 6.0 9.0 * 12.0 22.5 * 30.0 6.
Setup OSD Menu 1. Press the OSD joystick to start the OSD menu in any video output mode, 2. Move the joystick up or down to navigate through the menu options. 3. Move the joystick left or right to change a menu setting. 4. When a menu option or setting is followed by press the joystick to access to the next screen. 5. When a finger & button is present, press and hold the SET button, PUSHING will display once the setting has been changed. 6.
FOCUS ADJ OFF ON EXPOSUR E BRIGHTNE SS SHUTTER 0 - 20 Auto-Normal /Deblur Manual-1/30-1/30000 Flicker SENS-UP AGC RETURN Off/x2/x4/x8/x16/x32 0 -10 BACKLIG HT OFF HLC BLC FOCUST AREA DISP TONE H-Pos V-Pos H-Size V-Size RETURN MODE: IGHT ONLY/ALL DAY Level 0- 20 ColorBLK/Customize/WHT/ YEL/CYN/GRN/MAG/RE D/BLU RETURN H-Pos 0-20 V-Pos 0-20 H-Size 0-20 V-Size 0-20 Return
DAY&NIG HT WDR MODE: NORMAL/ROI ROI: WIND0W ZONE: 0-3 WINDOW USE: ON/OFF H-Pos 0-1920 V-Pos 0-1080 H-Size 0-1920 V-Size 0-1080 RETURN Weight – Low / Middle / High Return AUTO IR LED: ADAPTIVE/OFF Anti-Sat. 1 ~ 20 (Not used when smart IR off) D-N THRES 1 ~ 20 N-D THRES 1 ~ 20 Delay – Low / Middle / High Return COLOR B&W EXTERN COLOR AWB IR LED: ADAPTIVE/FULL/OFF Anti-Sat.
Color Gain Return MANUAL: C-Temp 5000K / 8000K / 3000K R-Gain 1 ~ 20 B-Gain 1 ~ 20 Return 1 - 20 DNR DNR OFF/LOW/MIDDLE/HIGH IMAGE SHARPNES S GAMMA MIRROR FLIP ACE 1 ~ 10 DEFOG PRIVACY 0.55 / 0.65 /0.75 / 0.
RETURN CB Level (1 ~ 20) / Return MOTION OFF/ON Det Window Window Zone 0 ~ 3 Window Use On/Off Det H-Pos / Det VPos / Det H-Size Det / V-Size Return Det Tone 0 - 4 MDRECT FILL On/Off Sensitivity 0 - 10 Motion OSD On/Off Text Alarm On/Off Signal Out Off/On Return SYSTEM OUTPUT MODE AHD/TVI/CVI/CVBS FRAME RATE 1080P 30FPS (DO NOT CHANGE!!!) FOR NTSC FREQUEN CY 60HZ (DO NOT CHANGE!!!) FOR NTSC CONFIRM YES (PLEASE SAVE IT) IMAGE RANGE FULL / COMP / USER USER: OFFSET 0 – 32
COLOR SPACE RETURN HD-CbCr / YUV / SDCbCr COLOR BAR OFF/ON LANGUAG E ENG / CHN / CHN(S) / JPN / KOR CAM TITLE Off / Right Up / Left Down RESET RETURN EXIT ON EXIT&SAVE/EXIT&CANC EL OSD Menu Description The following menu description gives more in depth information about the menu options. In some instances recommendations are made to hopefully enhance the results. However every installation will be different and there will occasions when alternative solutions may be more suitable.
EXPOSUR E BRIGHTNE SS SHUTTER SENS-UP AGC RETURN 0 - 20 Auto-Normal /Deblur Manual-1/30-1/30000 Flicker Off/x2/x4/x8/x16/x32 0 -10 Brightness Adjust the camera’s brightness from 0~20. The higher the number, the brighter the image will appear. SHUTTER Select either AUTO, MANUAL or FLICKER. • AUTO: Automatic shutter speed/control. NORMAL: Set when the camera is installed in an indoor environment. DEBLUR: Set when the camera is installed in an outdoor environment.
NOTES: • You need lower AGC level to make the image dark enough to active SENS-UP. • SENS-UP may be disabled depending on manual SHUTTER settings. • The higher the SENS-UP level, the brighter the screen, but the more likely it is that an after-image will appear. Possible image blur is normal with increased zoom while using SENS-UP.
H-Size 0-1920 V-Size 0-1080 RETURN Weight – Low / Middle / High Return HLC (High Light Compensation) If the scene contains extremely bright light areas such as car headlights, the light can mask out much of the on-screen detail. Use the HLC feature to remove these bright lit areas to allow detail, such as a car license plate number, to become more visible. • LEVEL: The lower the level, the more of the HLC mask will be applied. • COLOR: Black, White, Yellow, Cyan, Green, Magenta, Red, and Blue.
• H-POS: Adjust LEFT or RIGHT to move the Horizontal Position. • V-POS: Adjust LEFT or RIGHT to move the Vertical Position. • H-SIZE: Adjust LEFT or RIGHT to increase or decrease the Horizontal Size. • V-SIZE: Adjust LEFT or RIGHT to increase or decrease the Vertical Size. WDR (Wide Dynamic Range) This function illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas.
DAY&NIG HT EXTERNAL AUTO COLOR B&W SMART IR: OFF/ON Anti-Sat. 1 ~ 20 (Not used when smart IR off) Extern S/W: LOW/HIGH D->N Level 1 ~ 20 N->D Level 1 ~ 20 Delay: Low / Middle / High Return SMART IR: OFF/ON Anti-Sat. 1 ~ 20 (Not used when smart IR off) AGC Threshold 1 ~ 20 AGC Margin 1 ~ 20 Delay – Low / Middle / High Return SMART IR: OFF/ON Anti-Sat.
AUTO ↵ (Default) The mode is switched to ‘COLOR’ in a normal environment, but switches to ‘B/W’ mode when ambient illumination is low. • ANTI-SAT: Cameras equipped with IR LEDs may have an over-saturated night time image. Adjust the level of ANTI-SAT to compensate for over-saturation. • D>N THRES: Day to Night change level. • N>D THRES: Night to Day change level. • DELAY: Sets a delay time before the switch is made from day to night/night to day.
Return AUTO Select this to automatically readjust the white balance each time a change in the ambient color temperature is detected. AUTOext AUTOext is used in larger color map than AUTO mode. PRESET Automatically readjust only by a simple press and hold until the desired auto white level is reached. MANUAL ↵ Select this to fine-tune white balance manually. Color Temp (°Kelvin) and Red / Blue gain values are adjustable. COLOR GAIN The setting range is 0 ~ 20.
This function reduces background image noise in a low light environment, improving visibility. Off / Low / Middle / High NOTES: When adjusting the noise reduction level, remember that the higher the level is set, the greater the reduction in noise level, as well as the brightness of the image but trailing may occur with moving objects. IMAGE SHARPNES S GAMMA MIRROR FLIP ACE DEFOG PRIVACY 1 ~ 10 RETURN 0.55 / 0.65 /0.75 / 0.
H-Pos / V-Pos / H-Size / V-Size / Y-Level (1 ~ 20) / CR Level (1 ~ 20) / CB Level (1 ~ 20) / Return RETURN This function includes features that allow you to make adjustments to fine-tune the quality of the image displayed on the monitor. SHARPNESS The outline of the image becomes cleaner and more distinctive as the SHARPNESS level increases. If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear. GAMMA Adjust how light and color are displayed.
DEFOG: Images in extraordinary environments such as fog, smoke, rain or smog have a dynamic range lower than ordinary images. This function is a contrast enhancement, which is used to overcome such shortcomings. PRIVACY ↵ Apply a mask to an area you want to hide. Useful in areas where a camera can see into areas that are not relevant to security needs. Zone Num (0 ~ 15): This function allows the creation of up to 16 colored areas to be created to provide privacy masking.
Det H-Pos / Det VPos / Det H-Size Det / V-Size Return Det Tone 0 - 4 MDRECT FILL On/Off Sensitivity 0 - 10 Motion OSD On/Off Text Alarm On/Off Signal Out Off/On Return Monitor activity more efficient with this feature by means of highlighting moving objects with a red outlined box around the moving object. DET WINDOW ↵ Choose from 4 different detection windows to adjust their size and position as needed. DET TONE Select the motion area transparency.
When motion is detected text will be displayed on screen to alert you the motion. SIGNAL OUT Not supported.
RESET RETURN ON Output Mode Please do not change the video format! It will lose signal if change it to others mode that your DVR do not support. Please leave all the settings of video mode in default and do not change them. FRAME RATE Set the frame rate and resolution output from the camera.
SD-CbCr (Standard Definition Chrominance Blue and Red) COLOR BAR Color bar pattern output. LANGUAGE Change the language of the OSD Menu. ENGLISH, CHINESE, CHINESE (S), JAPANESE or KOREAN CAM TITLE Use this feature if you want to quickly identify a given image by assigning a title that will display on screen. 1) Select CAM TITLE, then use the LEFT/RIGHT button to set it to “RIGHT UP” or “LEFT DOWN” and then press the SET button.
Scanning System Progressive Scan Lens Focus Length 2.
Dimension 220(W) x 80(H) x 80 (D)mm Weight 1400g *Stated maximum IR range is based on ideal conditions in typical outdoor environment. Actual range and image clarity depends on installation location, viewing area and light reflection / absorption level of object. Trouble Shooting a. No picture or only black and white picture after applying power (i) Check all plugs and cables are securely connected to the proper connectors. (ii) Ensure your power supply is providing the correct voltage and current.
(iii) Adjust the contrast feature of the monitor. (iv) Make sure that the screen is not exposed directly to a bright light. Move the camera if necessary. (v) The power supply voltage level may be unstable, therefore, try another power supply. (vi) Ensure the cables are correctly connected and/or the cables are of the correct impedance. d.
Frequently Asked Questions Q: Does this camera work with 720P DVR system? A: No, the video signal is 2MP 1080P, it could not work with 720P DVR. Q: How should I switch the video mode? A: Please check notice before using above. Q: Will the OSD switch stay in same mode if camera is powered off, or do you have to reset mode each time you power it back up? A: It will stay in the same output mode, do not need to reset each time.
Warranty and Customer Service 60-Day Money-Back Guarantee for Any Reason You may return your undamaged product and packaging within 60 days of purchase to receive a FULL REFUND for any reason. If the reason for return isn’t quality-related, the customer must pay the return shipping costs. 24-Month Warranty for Quality-Related Issues Honic warrants this product against defects in workmanship and material for a period of 2 years from its original purchase date.
