HB Wireless Communication Technology HB300N USER MANUAL FCC ID: 2AJIC-HB300N Model Name: HB300N Product Name: NFC module Description: NFC reader/writer module compatible Version: V1.0 HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
Contents 1. 2. 3. Introduction .......................................................................................................... 3 Hardware Block Diagram ................................................................................... 4 Pin Definition ........................................................................................................ 5 3.1 Host Interface ............................................................................................. 5 3.2 Antenna Interface ...
1. Introduction HB300N is a kind of NFC module that could be embedded in one IT system by simply connecting the module through I2C interface and start developing his application soft. Top Side Bottom Side HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
2. Hardware Block Diagram HB300N is a full feature NFC module and compliant with NFC standards (NFC Forum, EMVCo, ETSI/SCP). HB300N has an optimized architecture for low-power consumption in different operation modes. The RF contactless front-end is supporting various transmission modes according to NFCIP-1, NFCIP-2, ISO/IEC1444e, ISO/IEC 15693, ISO-14443, MIFARE, and FeliCa specifications.
3. Pin Definition 3.1 Host Interface Pin number Name 1 MOD_VDD Configuration Power Supply Input Description Module power supply 2 MOD_GND Power Supply Ground Module ground 3 SWP Input/ Output 4 MOD_VUP Power Supply Input Single Wire Protocol line to UICC/ SIM Power supply for RF Front-end 5 IRQ Output Interrupt request from module to platform 6 VDD_SIM Power supply input The power rail used to power UICC/SIM.
3.2 Antenna Interface Pin number 1 2 3 4 5 6 7 Name ANT1 RXP TX1 GND TX2 RXN ANT2 Configuration Output Input Output Ground Output Input Output Description Antenna connection for Card emulation Contactless receiver input Contactless receiver output 1 Transmitter ground Contactless receiver output 2 Contactless receiver input Antenna connection for Card emulation HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
4. 4.1 Power & Current Consumption Power modes & Power Reset 4.1.1 Power modes 4.1.2 Reset and download concept To enter reset there are 2 ways: • Pulling VEN voltage low (Hard Power Down state) • if VBAT monitor is enabled: lowering VBAT below the monitor threshold (Monitor state, if VEN voltage is kept above 1.1 V) To get out of reset: • Pulling VEN voltage high with VBAT above VBAT monitor threshold if enabled HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
4.2 3.3V Condition Test Condition: MOD_VDD = 3.3V, VDD_IO= 3.3V, MOD_VUP=5V Impedance of Antenna Matching: 35 ohm 3.3V Power Rail Current (mA), Booster “OFF” (MOD_VDD + VDD_IO + VDD_SIM)*1 Standby (RF OFF, VEN Pull Low) Polling Mode *2 AVG Peak 0.083 N/A AVG 1.99 Peak 10.2 Type 1 Type 2 Topaz Mifare AVG 7.5 7.5 Communicating Peak 9.4 9.8 *1: Means NFC module “Digital part” power consumption *2: Means “Normal” polling mode. Detected Test Tag type Type 3 Type 4 Felica Mifare Desfire 7.6 7.7 9.8 9.
4.3 5V Condition 5V Power Rail Current (mA), Booster “OFF” Standby (RF OFF, VEN Pull Low) Polling Mode (MOD_VUP) *3 AVG Peak 0 N/A AVG 75.4 Peak 75.6 Type 1 Topaz AVG 12 Communicating Peak 48 *3: Means NFC module “RF part” power consumption Detected Test Tag type Type 2 Mifare 50.4 53.6 Type 3 Type 4 Felica Mifare Desfire 59.4 55.79 72.8 73.
4.4 Total Condition Total power consumption (mW), Booster “OFF” Standby (RF OFF, VEN Pull Low) AVG Peak Polling Mode AVG Peak Detected Test Tag type Communicating AVG Peak 0.274 N/A Type 1 Topaz 84.75 271.02 383.57 411.66 Type 2 Type 3 Type 4 Mifare Felica Mifare Desfire 276.75 322.08 304.36 300.34 396.34 400.84 Total power consumption (mW), Booster “ON” Standby (RF OFF, VEN Pull Low) Polling Mode AVG Peak AVG Peak Detected Test Tag type Communicating 0.274 N/A AVG Peak Type 1 Topaz 710.
5. Reference Circuit 4.1 No SIM Card 5.2 SIM Card used HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
6. Dimension & FPC Connector Mechanical HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
Antenna FPC Connector 7pin Number of Contacts A B C D 7 5.5 3 4.03 4.88 Host Interface 15Pin Number of Contacts A B C D 15 9.5 7 8.07 8.85 HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
7. Certifications and Regulatory Item Feature Description 1.1 FCC FCC PART 15C FCC PART 15B 1.2 CE CE EN 300 330 CE EN 301 489-3 CE EN62311 MPE REPORT CE EN62368-1 1.3 IC IC RSS-247 1.4 RCM RCM SDoC 1.5 MIC VCCI-32 1.6 NCC LP0002 CNS13438 1.7 AS/NZS AS/NZS4268 CISPR 32 AN/NZS 62368-1 1.8 KNRF KN301489 General: This modular approval is limited to OEM/Integrators installation only.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that this condition cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product.
plication or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations The product is a low power device and its output power is lower than FCC SAR exemption level. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. • Antenna type: Loop 2.
re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC:25868-HB300N”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs.
低功率電波輻射性電機管理辦法 第十二條 : 經型式認證合格之低功率射頻電機，非經許可，公司商號或使用者均 不得擅自變更頻率加大功率或變更原設計之特性及功能。 第十四條 : 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業科學及醫療用電波輻射性電機 設備之干擾。 HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
8. Marking HONGBO WIRELESS COMMUNICATION TECHNOLOGY CO.,LTD. 4F., No.143, Sinhu 1st Rd.
