HKRUR-3083 FRID long distance electronic tag reader Instruction Catalog
Catalogue 1. Brief instruction of HKRUR-3083 Reader .............................................................3 1．1 The use of HKRUR-3083 Reader ...............................................................3 1．2 The main function of HKRUR-3083 Reader..............................................3 1．3. Technology parameter of the HKRUR-3083 .............................................4 2．The confifuration and interface instruction of HKRUR-3083 Reader ....................
1. Brief instruction of HKRUR-3083 Reader The products can be compatible with multi-protocol, small volume, quickly read and multi-tag identification.,the round- polar antenna is no limit of direction for tag, water proof, Meanwhile, it can be used widely in RFID systems, the mainly applying sites are † † † † † Logistics and warehouse Management:：goods flow, warehouse management, and the flowing management of mail, parcel, and luggage.
exploitation,, therefore convenient for use.. 5) Connect the controller of PC machine through the communication interface to process the data communication and exchange, and to provide SDK exploitation bag,, so as to make customers exploit for use again. 1．3. technology parameter of the HKRUR-3083 1）Operation frequency: China standard（920~925MHz）,FCCstandard903~927MHz)or order other frequency band to work in jumping frequency appointed frequency..
Define +9V GNE 2． 2 TX RX GND A+ B- TRIGGER GND DATA0 DATA1 Port explain 2.2.1 RS232 The reader provide RS232 communication interface for cooncting communication with control nainframe((commonly the PC machine),the data format of the RS232 interface is 8 data bits, a star bit and a stop bit, without parity bit; 9600，19200，38400，57600 and 115200 are the choices for data modulus..
“ 0” ,anothere line indicates“ 1” ,and the third one is “ GND” . The typical format of every data is like the following picture showing., Of course, users can settle the data formal of the Wiegand interface according the special demand of the controller machine In order to improve the of the reliability of data transmission ,the reader supply multi-transmission function, namely when reading one tag,the Wiegand interface will be multi-transmission in interval in some time.
through appointed communication interface. This mode is only for reading to the tag operation. 2 ． 4 ． 3overwrite working((TRIGGER READ when the touching off port inputs low voltage, ,reader begins to read card in cycle ,and shut off in a period of time. 2．5．Interfacing identification: Interfacing identification is designed for reducing the prolixity of the data that reader uploads. If choosing the function ,reader will only upload a set of data when reader reads the same card in multi-connection.
6 setting interface Reader address rejigger： 7 setting interface If you want to amend the address of the reader, you can choose the new address under the frame of the amending address column of the reader ,then click the ¡°set¡±button. The new address will bu effective when reader reposition work mode choice： setting interface Users can configure the work mode of the reader through single choosing frame..
at the same time, and other part become gray.. when choosing timing or touching off mode Reader can set the parameter of radio frequency timer and communication interface. If choosing touching off mode, ,it can set the parameter of the trigger. We will describe them one by on as the following. setting interface Users can set the power and frequency of the radio frequency according application need. The largest power parameter can be 30dBm.
Interface setting This frame is used for setting the Wiegand interface parameter, ,Include Wiegand output times and signal format. Wiegand signal format needs setting Wiegand pulse breath(means low impulse breath)and code element cycle(means the time of a bit data) After every function choosing, click¡±SET¡±button The successful setting parameter will be effective when reader repositions. Suers can click¡±Restar¡±button to make reader reposition. Fourth The fitting of HKRUR-3083 Readerf 4.
HKRUR-3083Reader HKRUR-3083 Reader Frank fitting like the figure 1 crutch fitting like the letterL The fitting modes of the reader 4．2 the fixation and height adjustment of the reader When frank fitting ,it demands that the crutch dia.of the reader 50 to 60mm while length2.2m Using stain steel material that more than 1.3m thick is the best choice. Fix the reader to the top of the crutch with the self-provided fastening pin in the casing of HKRUR-3083 reader .
carriage drive. 5. The demo program instruction pf HKRUR-3083 The demo program of the reader provides the contend of all kinds of operation to the tag and parameter setting of radio frequency Users can evaluate the function of the function of the reader through this demo program, of consider to make the second exploitation of the reader. The demo program of the reader includes ¡±DEMO exe¡±and ¡°MR915ApiV10.
NOTES: 1. Frequency Range: 903MHz-927MHz. 2. The transmission and receiver is the same for the 20dB bandwidth. 3. The transmission of each channel of the transmitter is to send sync code. The receiver will recognize the sync code, confirm the channel and analyze the data. 4. Each frequency is used equally on the average by each transmitter. 5. The transmission channel is based on the Hop data as below: Channel to Frequency Table (MHz) 0 1 2 3 4 5 6 7 8 9 903.00 903.48 903.96 904.44 904.
