xbi2_maual.
xbi2_maual.
2 ChatterBox! strives to provide our customers with powerful and reliable communication systems that offer state-of-theart technology and cutting edge design. Every communication system in the ChatterBox! product line provides unique features and benefits along with communication compatibility within the entire product range.
CONTENTS 1. KIT INCLUDES 4 1.1 OPEN FACE KIT 4 1.2 FULL FACE KIT 4 2. XBI2 DESCRIPTION 5 2.1 EXTERIOR DESIGN 5 2.2 DESIGN DESCRIPTION 5 2.2.1 POWER Button 5 2.2.2 MODE Button 5 2.2.3 VOLUME UP Button 5 2.2.4 VOLUME DOWN Button 5 2.2.5 INTERCOM Button 5 2.2.6 CHARGE PORT 5 2.2.7 HEADSET PORT 5 2.2.8 LED 5 3. INSTALLATION 6 3.1 GENERAL INSTALLATION 6-7 3.2 ALTERNATIVE FULL FACE XBI2 UNIT HEADSET INSTALLATION 7 4. BASIC OPERATION 7 4.1 CHARGING XBI2 UNIT 7-8 4.2 TURNING XBI2 UNIT ON / OFF 8 4.2.
1. KIT INCLUDES NO. DESCRIPTION Q’TY 1 XBi2 Main Unit 1 2 AC Home Charger 1 3 Open Face Headset 1 4 Pre-Installed Lithium-Polymer Battery 1 5 Plastic Base Plate 1 6 Metal Mounting Bracket 1 7 Rubber Pad 1 8 Foam Speaker Covers 2 9 Popsicle Stick 1 10 Phillips Screws 3 11 Double Sided Mounting Tape 1 12 Sticky Back Velcro Discs 2 13 Wire Clips 2 1.2 FULL FACE KIT 1.1 OPEN FACE KIT NO.
2. XBi2 DESCRIPTION 2.1 Exterior Design Power Volume Up Charge Port Intercom LED Headset Port Mode Volume Down 2.2 DESIGN DESCRIPTION 2.2.1 POWER BUTTON *Power ON/OFF of main unit *BLUETOOTH® pairing mode *When the BLUETOOTH® phone is connected, use hands-free mode (An swer/Hang up phone call) GROUP INTERCOM pairing mode (with MODE button) 2.2.2 MODE BUTTON *MP3 mode source select between BLUETOOTH® MP3 and AUX MP3 *GROUP INTERCOM pairing mode (with POWER button) 2.2.
3. INSTALLATION Figure 1 Slot “B” Slot “B” Threaded hole “C” Tab “A” Tab “A” Screw “D” 3.1 GENERL INSTALLATION 1. Attach plastic base plate to metal mounting bracket by aligning tabs “A” with slots “B” and sliding plastic base plate onto metal mounting bracket. Insert screw “D” through metal mounting bracket and into threaded hole “C” and tighten. (Figure 1) 2. Attach the foam covers and sticky backed velcro discs to the speakers. (Figure 2) 3. Place the helmet upside down on a soft surface.
3.2 ALTERNATIVE FULL FACE XBI2 UNIT HEADSET INSTALLATION 1.Attach double sided mounting tape to the back side of the plastic base plate. Position the plastic base plate at approximately the middle bottom of the left side of the helmet and apply. 2.Install speakers at stated in step 2 & 5 of the previous instructions. 3.Position and attach the microphone to the middle of the helmet chin bar directly in front of the mouth.
4.2 TURNING XBI2 UNIT ON / OFF 4.2.1 TURNING ON 1. Press and hold the Power button until LED lights steady RED 2. Release Power button 3. LED will now alternate flashing BLUE & flashing RED continuously 4.2.2 TURNING OFF 1. Press and hold the Power button until LED lights steady RED 2. A two-tone sound will be heard 3. Release Power button 4. LED will now be off 4.3 BATTERY LEVEL STATUS DISPLAY 1. Press the Power button around 1second, RED LED will stay “ON” then release the Power button. 2.
5.2 PAIRING XBI2 UNITS TOGETHER *** MAIN UNIT MUST BE ON AT ALL TIMES TO COMMUNICATE BIKE-TO-BIKE *** 5.2.1 PAIRING 3 XBi2 UNITS TOGETHER - RIDER:1 (MAIN) RIDER: 2 (SATELLITE 1) RIDER:3 (SATELLITE 2) 1. Turn on Main, Satellite (1) and Satellite (2) units on 2. Get the Main unit. Press & hold the Power button and the Mode button simultaneously 3. LED will start to flash RED and occasional BLUE after 3 seconds 4. Release both Power button and the Mode button 5. Now get the Satellite (1) unit.
6. FUNCTION OPERATION 6.1 BLUETOOTH® / WIRED AUDIO DEVICE *** ALWAYS PAIR STEREO AUDIO SOURCE TO XBI2 BEFORE PAIRING PHONE *** 6.1.1 PAIRING A STEREO BLUETOOTH® ADAPTOR 1. Put XBi2 unit in Bluetooth® pairing mode (turn to 5.1) 2. Turn on audio source and connect Bluetooth® adaptor for pairing 3. Audio source will automatically start playing through XBi2 unit when pairing is complete 4. XBi2 unit is now paired with Bluetooth® adaptor. (Pairing process will no longer be needed to connect) 6.1.
6.2.2 ANSWERING A PHONE CALL 1. When a phone call is received a 3 tone sound will be heard 2. Momentarily press (approximately 1 second) and release the Power button 3. Stereo audio source and/or intercom communication will be muted 4. Conduct phone call 5. To end call, momentarily press (approximately 1 second) and release the Power button 6. Stereo audio source and/or intercom communication will be restored 6.2.3 PLACING A PHONE CALL * 1. Dial desired number and press talk or connect on phone keypad 2.
7.3 CONNECTING A PAIRED STEREO BLUETOOTH® ADAPTOR AND PAIRED BLUETOOTH® PHONE AT THE SAME TIME 1. 2. 3. 4. 5. 6.
8.3 BUTTON FUNCTION SUMMARY NO. BUTTONS DESCRIPTION TIME LED & BEEP REMARK 1 POWER POWER ON 1 sec ↑ RED + BLUE RED LED ON POWER OFF 5 sec ↑ RED + BLUE RED LED ON Hands-Free 1 sec ↓ - Make Call, Answer Call BLUETOOTH® PARING 7 sec ↑ BLUE BLUETOOTH® Pairing Mode Entering GROUP MASTER 2 sec ↑ RED [200ms] GROUP SLAVE 1 sec ↓ RED[100ms] GROUP INTERCOM Pairing Mode Entering (After finish Auto Power OFF) BLUETOOTH® MP3 Select 4 sec ↓ 4-Tone In MP3 MODE AUX.
10. LICENSE INFORMATION 10.
11. FREQUENTLY ASKED QUESTIONS QUESTIONS ANSWERS 1) How many XBi2 units can communicate to each other? 1) You can have up to 3 XBi2 units to communicate to each other. 2) What is the range of the XBi2? 2) The XBi2 units can communicate up to 500 meters in optimum conditions. 3) Why does the LED light on the XBi2 not turning off, no matter what I do? 3) You will need to unscrew the 4 screws and unplug the battery to hard reset the unit.