Install Instructions

ManualsBrandsHoneywell Manuals2-Way VC Valve Assemblies1/2" Female NPT VC Valve Assembly (2.3 Cv)

Table Of Contents

INSTALLATION INSTRUCTIONS

95C-10948-04

VCZA,B,M,N Series

CARTRIDGE VALVE FOR USE WITH VC SERIES

The VC hydronic valve consists of a valve body and

replaceable characterized cartridge assembly.

Depending on the valve model selected, they can be used

with a VC2114 or VC8114 series actuator to provide on-off

flow control, or with a VC6930 or VC7930 series actuator

to provide proportional flow control. Two way bodies may

be plumbed in either direction. Three-way bodies may be

used in either diverting or mixing applications.

Replacing the cartridge rebuilds the valve. The valve body

should be able to stay in the pipes indefinitely.

VC actuators, ordered separately, use cam-operated

cartridge travel to resist water hammer. Limit switches

prevent motor overrun.

SPECIFICATIONS

The specifications following are nominal and conform to

generally accepted industry standards. Resideo is not

responsible for damages resulting from misapplication or

misuse of its products or non-workmanlike installation

practices.

Operating Ambient:

32 to 150 °F (0 to +65 °C).

5-95% RH (non-condensing)

Fluid temperatures: 34 to 203 °F (1 to 95 °C)

Shipping and Storage Temperature: -40 to 150 °F

(-40 to +65 °C)

Atmosphere: Non-corrosive, non-explosive.

Valve Materials:

Body of brass, Cartridge of Ryton™ (polyphenylene sul-

phide),

Noryl™ (polyphenylene oxide), and Fortron

O-ring seals of EPDM rubber

Stem of stainless steel

Pressure Rating:

Static – 300 psig (20 Bar) maximum.

Burst – 1500 psig (100 Bar)

Operating Differential and Close-off – 60 psi maximum

(4 bar)

Stem Travel: 0.4 inches (10 mm)

Flow Characteristics: Linear or equal percentage, per

Table 2.

Spring Force:

1000 and 6000 Series (Silver): 14 lbf.

3000 and 7000 Series (Red): 20 lbf.

Fig. 1. Nominal dimensions in inches [millimeters]

Summary of content (4 pages)

PAGE 1
VCZA,B,M,N Series CARTRIDGE VALVE FOR USE WITH VC SERIES INSTALLATION INSTRUCTIONS Fluid temperatures: 34 to 203 °F (1 to 95 °C) Shipping and Storage Temperature: -40 to 150 °F (-40 to +65 °C) Atmosphere: Non-corrosive, non-explosive. Valve Materials: Body of brass, Cartridge of Ryton™ (polyphenylene sulphide), Noryl™ (polyphenylene oxide), and Fortron O-ring seals of EPDM rubber Stem of stainless steel The VC hydronic valve consists of a valve body and replaceable characterized cartridge assembly.
PAGE 2
VCZA,B,M,N SERIES [2] Models are country specific. Not all models are available in all markets. Cv values in greyed-out boxes are listed for reference only. [3] A port is 5% higher, and B port is 5% lower in mixing configuration. B port is 5% higher, and A port is 5% lower in diverting configuration Table 1. VC Valve assembled dimensions Dimension C D E Pipe Fitting Sizes mm inches mm inches mm 1/2" SWEAT 89 3-1/2 130 5-1/8 1/2" NPT (int.
PAGE 3
VCZA,B,M,N SERIES INSTALLATION PLUMBING When Installing This Product... The valve may be plumbed in any angle, including vertical piping, but preferably not with the actuator below horizontal level of the body. Make sure there is enough room around the actuator for servicing or replacement. 1. 2. 3. 4. 5. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.
PAGE 4
VCZA,B,M,N SERIES 1. 2. 3. 4. 5. Disconnect power supply before servicing to avoid electrical shock or equipment damage. Depending on the installation, it may be necessary to disconnect leadwires to valve actuator, or depress tab on Molex™ connector and remove. Where appropriate, label wires for rewiring. Remove valve actuator by pressing up on the latch mechanism located directly below the red manual open lever with thumb (See Figure 5).