Submittal Sheet

ManualsBrandsHoneywell ManualsAir CleanersSmartLamp UV Surface Treatment System, Coil Irradiation Model

Table Of Contents

PRODUCT DATA

68-0262-5

UV100E Ultraviolet Systems

UV100E1043 AND UV100E2009 AIR TREATMENT SYSTEMS

UV100E3007 SURFACE TREATMENT SYSTEM

APPLICATION

When installed in forced air heating and cooling systems, the

UV100E Ultraviolet Systems kill airborne or surface micro-

organism contaminants like mold and bacteria.

The UV systems use patented SmartLamp™ control

technology that monitors the HVAC system to operate the

lamps only when needed. This technology extends bulb life up

to five times and reduces power consumption, lowering

operating costs. The UV systems also include local

diagnostics with the SmartLamp™ LED and reset capability.

FEATURES

• SnapLamp™ features replacement lamp handle with

detachable replacement bulb, UC18W or UC36W, to

make replacement more economical.

• SmartLamp™ Control Algorithm determines optimal

UV lamp usage.

• SmartLamp™ LED shows bulb life and replacement.

• Reduced power consumption and extended bulb life.

• Communicates with other home appliances through

Enviracom™ three-wire communications bus.

• Automatic brownout and high temperature protection

for UV lamps.

• Return air models supplied with integrated airflow

sensor to monitor air flowing through ductwork.

• Dual-purpose reset button:

— Commands lamp on with a single one-second

push.

— Resets internal lamp run-time timer after bulb

replacement with extended five-second hold.

• UV-C light kills airborne bacteria and surface mold.

• UV lamp does not produce ozone.

• Easy lamp maintenance with quick, easy bulb

replacement.

• Sealed unit prevents accidental installer/homeowner

contact with high voltage and ultraviolet rays.

• Safe design prevents lamp from lighting unless base is

correctly mounted on HVAC duct.

• Lamp light indicator to safely view lamp operation.

• Power cord that plugs into 120 Vac electrical outlet.

• Five-year limited warranty.

Contents

Application/Features ......................................................... 1

Specification/Ordering Information ................................... 2

Installation ........................................................................ 3

Checkout .......................................................................... 7

Troubleshooting and Service/Maintenance ...................... 8

Parts List .......................................................................... 11

Summary of content (16 pages)

PAGE 1
UV100E Ultraviolet Systems UV100E1043 AND UV100E2009 AIR TREATMENT SYSTEMS UV100E3007 SURFACE TREATMENT SYSTEM PRODUCT DATA FEATURES • SnapLamp™ features replacement lamp handle with detachable replacement bulb, UC18W or UC36W, to make replacement more economical. • SmartLamp™ Control Algorithm determines optimal UV lamp usage. • SmartLamp™ LED shows bulb life and replacement. • Reduced power consumption and extended bulb life.
PAGE 2
UV100E ULTRAVIOLET SYSTEMS SPECIFICATIONS IMPORTANT This product is tested and calibrated under closely controlled conditions and some minor differences in performance can be expected if those conditions are changed. The specifications in this publication do not include normal manufacturing tolerances; therefore, an individual unit may not exactly match the listed specifications.
PAGE 3
UV100E ULTRAVIOLET SYSTEMS Selecting Mounting Location Temperature Ratings: Ambient Temperature Range: 30°F to 104°F (-2°C to 40°C). Bulb Temperature Range (In Moving Air): 30°F to 140°F (-2°C to 60°C). Relative Humidity: Up to 95% rh, non-condensing. CAUTION Dimensions: See Fig. 3. Approvals: Underwriters Laboratories: File no. E223009 The health aspects associated with the use of this product and its ability to aid in disinfection of environmental air have not been investigated by UL.
PAGE 4
UV100E ULTRAVIOLET SYSTEMS Surface Treatment System 1. When installed next to the cooling coil, the Surface Treatment System prevents a high percentage of the growth of micro-organisms such as mold that may grow on duct surfaces, coils and drain pans. Individual results depend on careful installation and maintenance. See. Fig. 2. 2. 3. 4. 5. 6. 7. Choose a location that is readily accessible for regular inspection and cleaning. Fig. 1 and 2 and show possible mounting locations.
PAGE 5
UV100E ULTRAVIOLET SYSTEMS SURFACE TREATMENT SYSTEM 3-1/2 (89) 1 (25) 7 (178) 2-1/4 (57) 14-7/8 (379) 4 (102) 3-1/2 (89) 4-1/2 (114) M20190A 7 (178) AIR TREATMENT SYSTEM (SINGLE LAMP) 3-1/2 (89) 1 (25) 7 (178) 2-1/4 (57) 1/2 (12) 4 (102) 7-7/16 (188) 3-1/2 (89) 4-1/2 (114) M20191A 7 (178) 5 (127) 3-1/2 (89) AIR TREATMENT SYSTEM (DUAL LAMP) 3-1/4 (83) 2-3/16 (56) 8-1/2 (216) 3-1/2 (89) 4 (102) 1/2 (12) 14-7/8 (379) 5 (127) 7 (178) M20192A 10 (254) Fig. 3.
PAGE 6
UV100E ULTRAVIOLET SYSTEMS 13. CAUTION Breakable Glass Hazard. Can cause personal injury. Be careful when inserting bulb(s) into lamp base. Wear protective gloves when handling bulb(s). Rotate the lamp handle clockwise until it snaps into place with the lamp light indicator aligned with the raised button on the unit cover. See Fig. 6. MERCURY NOTICE This device contains mercury in the sealed ultraviolet bulb(s). Do not place your used bulb(s) in the trash. Dispose of properly. Broken Bulb Cleanup.
PAGE 7
UV100E ULTRAVIOLET SYSTEMS 16. For air treatment systems, wait ten minutes for the airflow sensor to calibrate. During this time, the furnace fan must remain off. NOTE: Failure to wait ten minutes for the airflow sensor to calibrate before powering the furnace causes the airflow sensor to incorrectly calibrate and the device to incorrectly function. If this occurs, remove power to the furnace or turn off the system and fan, wait ten minutes, and then resume normal furnace operation. 17. 18. 19.
PAGE 8
UV100E ULTRAVIOLET SYSTEMS TROUBLESHOOTING AND SERVICE The Ultraviolet System has no field-serviceable parts. Bulb cleaning is recommended as routine maintenance quarterly or every three months. Bulb replacement is required when the LED on the front of the UV system is lighted solidly. See the Owner’s Guide for detailed procedural information. Quarterly Bulb Cleaning MERCURY NOTICE This device contains mercury (less than 5 mg) in the sealed ultraviolet bulb(s).
PAGE 9
UV100E ULTRAVIOLET SYSTEMS 7. Insert the lamp handle into the base with the lamp light indicator at the eleven o’clock position. Continue pushing and gently rotating counterclockwise until the lamp handle inserts fully into the base. See Fig. 14. M22847 M22841 Fig. 14. Position lamp handle for insertion back into lamp base. Fig. 11. Remove lamp or bulb. 4. Holding the lamp handle, wipe the lamp glass using a soft cloth dampened with window cleaner.
PAGE 10
UV100E ULTRAVIOLET SYSTEMS 10. For Air Treatment Systems, wait ten minutes for the airflow sensor to calibrate. During this time, the furnace fan must remain off. NOTE: Failure to wait ten minutes for the airflow sensor to calibrate before powering the system fan causes the airflow sensor to incorrectly calibrate and the device to incorrectly function. If this occurs, remove power to the furnace or turn off the system fan, wait ten minutes, and then resume normal fan operation. 11. 12.
PAGE 11
UV100E ULTRAVIOLET SYSTEMS PARTS LIST System Description Replacement Bulb/Handle Assembly Replacement Bulb UV100E1043 Air Treatment System (single-lamp) (left photo) UC100E1006 UC18W1004 UV100E3007 Surface Treatment System (center photo) UC100E1030 UC36W1006 UV100E2009 Air Treatment System (dual lamp) (right photo) UC100E1030 (two required) UC36W1006 (two required) M18621B 11 68-0262—5
PAGE 12
UV100E ULTRAVIOLET SYSTEMS ALIGN EITHER OF THESE LINES AS CLOSE AS POSSIBLE TO DUCT CENTER LINE CENTER OF 2 IN. (51 MM) HOLE FOR LAMP 3/32 IN. (3 MM) PILOT HOLES FOR MOUNTING SCREWS 1-1/2 IN. (38) HOLE FOR AIRFLOW SENSOR CENTER OF AIRFLOW SENSOR HOLE M20194A INSTALLATION TEMPLATE FOR AIR TREATMENT SYSTEM (SINGLE-LAMP). Fig. 18. Air Treatment System (single lamp) template. (Air Treatment System (dual lamp) template is located on next page.) Fig. 19. Air Treatment System (dual lamp) template.
PAGE 13
3/32 IN. (3 MM) PILOT HOLES FOR MOUNTING SCREWS CENTERS OF 2 IN. (51 MM) HOLES FOR LAMP 3/32 IN. (3 MM) PILOT HOLES FOR MOUNTING SCREWS 13 INSTALLATION TEMPLATE FOR AIR TREATMENT SYSTEM (DUAL-LAMP) CENTER OF AIRFLOW SENSOR HOLE 1-1/2 IN.
PAGE 14
UV100E ULTRAVIOLET SYSTEMS ALIGN EITHER OF THESE LINES AS CLOSE AS POSSIBLE TO DUCT CENTER LINE CENTER OF 2 IN. (51 MM) HOLE FOR LAMP 3/32 IN. (3 MM) PILOT HOLES FOR MOUNTING SCREWS INSTALLATION TEMPLATE FOR SURFACE TREATMENT SYSTEM Fig. 20. Surface Treatment System template.
PAGE 15
UV100E ULTRAVIOLET SYSTEMS 15 68-0262—5
PAGE 16
UV100E ULTRAVIOLET SYSTEMS Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 customer.honeywell.com ® U.S. Registered Trademark © 2007 Honeywell International Inc. 68-0262—5 M.S. Rev.