TABLE OF CONTENTS Honeywell Personal Weather Station INTRODUCTION 3 PRODUCT OVERVIEW 4 BEFORE YOU BEGIN 8 BATTERY INSTALLATION 9 LOW BATTERY WARNING 10 GETTING STARTED 10 PLACEMENT OF THE UNITS 10 REMOTE AND INDOOR TEMPERATURE 11 MAXIMUM AND MINIMUM READINGS 11 LOST COMMUNICATION 12 TRANSMISSION COLLISION 13 WWVB RADIO CONTROLLED TIME 13 ATOMIC CLOCK 14 TIME AND CALENDAR DISPLAY MODES 14 MANUAL SETTINGS 15 CLOCK ALARMS 15 SNOOZE 17 BACKLIGHT 17 PRECAUTIONS 18 TROUBLES
INTRODUCTION Thank you for selecting the Honeywell Wireless Personal Weather Station. This device combines precise time keeping with monitoring and displaying the PRODUCT OVERVIEW MAIN UNIT FEATURES · · New Double-Tool Design Time automatically sets to the US Atomic Clock · · 12 or 24 hours Time Format Dual crescendo Time Alarm with Snooze · One User Manual Please keep this manual handy as you use your new item.
· Activates clock’s manual programming mode F. DOWN ( ▼) button FRONT/REAR VIEW B A C · I · Activates manual remote channels search · Disables time alarms (W) and (S) and Ice Warning Alarm G. ALARM button · D E H J F G A. WEATHER AND TIME IN EASY-TO READ DIGITS B. SNOOZE/LIGHT button K · Stops the clock’s alarm temporarily · Activates a backlight for 5 seconds C.
REMOTE SENSOR · Keeps the remote sensor on the wall F. °C/ °F SWITCH FEATURES · New double-tool design · · Remote temperature transmission to the main unit via 433 MHz frequency · · Case can be wall mounted using built-in hanger Selection of the temperature display in Celsius or Fahrenheit · · Three channel selection LCD displays temperature, and channel A. LED INDICATOR · Flashes once when the remote sensor transmits a reading to the main unit. · Flashes twice when battery power is low. B.
2. The effective operating range may be influenced by the surrounding building materials and how the receiver and transmitter are positioned. 3. Place the remote sensor so that it faces the main unit (receiver), minimizing obstructions such as doors, walls, and furniture. 4. Though the remote sensors are weather-resistant, they should be placed away from direct sunlight, rain or snow. The best suggested location for the remote sensor for outdoors is under the eave on the north side of the building.
REMOTE AND INDOOR TEMPERATURE LOST COMMUNICATION The remote temperature information line is located on the top line of the main If the main unit display line for the remote sensor reading goes blank, press unit’s display. The wave icon is located above the remote channel number indicates the and hold DOWN (▼) button for 2 seconds to begin a new signal search. If the signal still isn’t received, please make sure that: reception status from the corresponding remote sensor.
TRANSMISSION COLLISION ATOMIC CLOCK Signals from the other household devices such as wireless doorbells, home Immediately after establishing communication between the main unit and security systems, and entry control, may interfere with this product or cause temporary reception interruption. This is normal and will not affect the general remote sensor, the atomic time signal receiver will open and start to search for the atomic time signal. The search usually takes between 5-8 minutes.
MANUAL SETTINGS subsequent days It is necessary to set the desired US TIME ZONE.
than the Weekday or Single alarm. PRECAUTIONS · Select the desired Ice Warning Alarm interval in 15 minutes increments between 15 and 90 minutes, using UP (▲) or DOWN (▼)buttons This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: · Press ALARM button to confirm and exit from the alarm setting mode. · · Do not immerse the units in water. Do not clean the units with abrasive or corrosive materials.
TROUBLESHOOTING SPECIFICATIONS Check here before contacting customer service.
FCC STATEMENT DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, We Name: Hideki Electronics, Inc. and (2) This device must accept any interference received, including interference that may cause undesired operation.
STANDARD WARRANTY INFORMATION This product is warranted from manufacturing defects for one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair. Note that online product registration is required to ensure valid warranty protection. To register your product, go to our Company website at: www.honeywellweatherstations.com. Click Online Product Registration under the Customer Service menu.