TABLE OF CONTENTS INTRODUCTION Honeywell Wireless In/Out Thermometer 3 PRODUCT OVERVIEW 4 BEFORE YOU BEGIN 8 BATTERY INSTALLATION 9 LOW BATTERY WARNING 10 GETTING STARTED 10 PLACEMENT OF THE UNITS 11 REMOTE AND INDOOR TEMPERATURE 11 MAXIMUM AND MINIMUM READINGS 11 LOST COMMUNICATION 12 TRANSMISSION COLLISION 13 WWVB RADIO CONTROLLED TIME 13 ATOMIC CLOCK 14 TIME AND CALENDAR DISPLAY MODES 14 MANUAL SETTINGS 15 CLOCK ALARMS 15 SNOOZE 17 BACKLIGHT 17 PRECAUTIONS 18 TROUBL
INTRODUCTION Thank you for selecting the Honeywell Wireless In/Out Thermometer. This device combines precise time keeping with monitoring and displaying the weather conditions from up to three remote locations. In this package you will find: • One main unit (receiver) • One remote sensor (transmitter) TS13C • One User Manual Please keep this manual handy as you use your new item. It contains practical step-by-step instructions, as well as technical specifications and precautions you should know.
B. SNOOZE/LIGHT button FRONT/REAR VIEW • I B • Activates a backlight for 5 seconds C. CHANNEL button A • Recalls a different remote sensor reading – 1,2 or 3 • Activates the remote channels search D. UP ( ▲) button • • • H • E Increases the parameters Activates US Time Zone selection mode Activates manual search for atomic time signal • Enables time alarms (W) and (S) and Ice Warning Alarm E. MODE button C G D F Stops the clock’s alarm temporarily J A.
I. WALL- MOUNT RECESSED OPENING C. RESET • Keeps the unit on the wall J. BATTERY COMPARTMENT • Resets all previous settings D. CHANNEL SWITCH • Accommodates 2 (two) UM-3 or AA 1.5V alkaline batteries K. REMOVABLE TABLE STAND • Selects the desired channel -1, 2 or 3 E. WALL-MOUNT RECESSED OPENING • Holds unit in upright position on a flat surface REMOTE SENSOR • Keeps the remote sensor on the wall F.
you intend measuring outdoor elements, place remote sensor outdoors • The main unit must be placed indoors. NOTE: 1. Avoid pressing any buttons on the main unit before the remote readings are displayed. 2. The effective operating range may be influenced by the surrounding building materials and how the receiver and transmitter are positioned. 3. Place the remote sensor so that it faces the main unit (receiver), minimizing obstructions such as doors, walls, and furniture. 4.
PLACEMENT OF THE UNITS The main unit can be placed on any flat surface indoors. The remote sensor can be placed indoors or outdoors, on a flat surface or mounted on the wall. temperature and humidity display. To clear the memory, press and hold MEM (memory) button for two seconds and all previously stored readings will be erased. REMOTE AND INDOOR TEMPERATURE LOST COMMUNICATION The remote temperature information line is located on the top line of the main unit’s display.
TRANSMISSION COLLISION ATOMIC CLOCK Signals from the other household devices such as wireless doorbells, home security systems, and entry control, may interfere with this product or cause Immediately after establishing communication between the main unit and remote sensor, the atomic time signal receiver will open and start to search for temporary reception interruption. This is normal and will not affect the general performance of the product.
MANUAL SETTINGS subsequent days It is necessary to set the desired US TIME ZONE.
30 will flash, meaning that if selected, the alarm will sound 30 minutes earlier than the Weekday or Single alarm. • • Select the desired Ice Warning Alarm interval in 15 minutes increments between 15 and 90 minutes, using UP (▲) or DOWN (▼)buttons Press ALARM ON/OFF button to confirm and exit from the alarm setting mode. PRECAUTIONS This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: • • Do not immerse the units in water.
TROUBLESHOOTING SPECIFICATIONS Check here before contacting customer service.
FCC STATEMENT DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including We Name: Hideki Electronics, Inc. Address: 7865 SW Mohawk interference that may cause undesired operation.
STANDARD WARRANTY INFORMATION This product is warranted from manufacturing defects for one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, commercial use, or unauthorized adjustment and repair. Note that online product registration is required to ensure valid warranty protection. To register your product, go to our Company website at: www.honeywellweatherstations.com. Click Online Product Registration under the Customer Service menu.