RTH7400, RTH7500 Series Programmable Thermostat Quick Installation Guide Included in your box Quick Install Guide Screws and anchors RTH7400/RTH7500 Thermostat UWP™ Mounting System (UWP) Tools you will need Tools you may need Phillips screwdriver Small flat head screwdriver Pencil Level Wire stripper Needle-nose pliers Drill and drill bit (7/32 in)
Quick Installation Guide Removing your old thermostat 1 Turn power OFF. To protect yourself and your equipment, Turn off the power at the breaker box or switch that controls your heating/cooling system. ON OFF OFF Switch Breaker box 2 Check that your system is off. Change the temperature on your old thermostat. If you don’t hear the system turn on within 5 minutes, the power is off. 75 ON OFF Note: If you have a digital thermostat that has a blank display, skip this step.
RTH7400/RTH7500 Series 5 Take a picture of how your wiring looks right now. Be sure to include the letters next to the terminals where the wires are inserted. This will be a helpful reference when wiring your thermostat. Tip: If the color of your wires has faded or if 2 terminals have the same wire color, use the wire labels provided in the package to label each wire. 6 7 Remove any jumpers. A jumper connects one terminal to another terminal.
Quick Installation Guide 9 Disconnect the wires and remove the old wall plate. Use a screwdriver to release wires from terminals. Then, use a wire label to identify each wire as it’s disconnected. The letter on the wire label should match the letter on the terminal. Tip: To prevent wires from falling back into the wall, wrap the wires around a pencil. Installing your RTH7400/RTH7500 thermostat RTH7400/RTH7500 Thermostat UWP Mounting System Screws 10 Bundle and insert wires through the UWP.
RTH7400/RTH7500 Series 11 Insert the wall anchors. It is recommended that you use the wall anchors included in the box to mount your thermostat. You can use the UWP to mark where you want to place the wall anchors. a) Level the wall plate. b) Mark the location of the wall anchors using a pencil. c) Drill the holes. d) Insert wall anchors. e) Make sure anchors are flush with wall. Tip: Use a 7/32 drill bit. 12 Set R-switch position and insert R-wire or wires.
Quick Installation Guide 13 Connect wires from Step 8. Depress the tabs to put the wires into the inner holes of their corresponding terminals on the UWP (one wire per terminal) until it is firmly in place. Gently tug on the wires to verify they are secure. Tip: If you need to release the wires again, push down the terminal tabs on the sides of the UWP. This wiring is just an example, yours may vary. 14 Mount the UWP and close the door. 8” to 3/ 1/4” Mount the UWP using the provided screws.
RTH7400/RTH7500 Series 18 Turn your power ON. Turn on the power at the breaker box or switch that controls the heating/ cooling system. ON ON OFF Switch Breaker box ON Set date and time 19 Set the date. OFF Press + or - to adjust the year. Press Select. Press + or - to adjust the month. Press Select. Press + or - to adjust the day. Press Select. 20 Choose a clock format. Press + or - set the clock format: 12 hour (standard for North America) or 24 hour. Press Select. Back 21 Set the time.
Quick Installation Guide System Setup 22 Select System Setup options. Press + or - to change values or select from available options. Then press Select to save changes and advance to the next System Setup number. See “System Setup options” below for a full list of System Setup numbers and options. Repeat until all of the System Setup options have been set. The thermostat will automatically save and exit to the Home screen. 23 Continue to “System operation settings” on page 10.
RTH7400/RTH7500 Series Number Description Options (factory default in bold) 218 Reversing Valve O/B 0 = O (O/B in Cool) 1 = B (O/B in Heat) Note: This option is only displayed if the Heat Pump configured. Select whether reversing valve O/B should energize in cool or in heat. 220 Cool Stages / Compressor Stages 200=Conv / 200=HP 0, 1, 2 Note: Select how many Cool or Compressor stages of your equipment the thermostat will control. Maximum of 2 Cool/Compressor Stages.
Quick Installation Guide System operation settings 1 Press the Mode button to cycle to the next available System mode. 2 Cycle through the modes until the required System mode is displayed and leave it to activate. NOTE: Available System modes vary by model and system settings. System modes: ‒‒ Auto: Thermostat selects heating or cooling as needed. ‒‒ Heat: Thermostat controls only the heating system. ‒‒ Cool: Thermostat controls only the cooling system.
RTH7400/RTH7500 Series Program Schedule You can program four time periods each day, with different settings for weekdays and weekends. We recommend the pre-set settings (shown in the table below), since they can reduce your heating/cooling expenses. Wake - Set to the time you wake up and the temperature you want during the morning, until you leave for the day. Away - Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
Quick Installation Guide Program schedule override (temporary) 1 Press + or - to adjust the temperature. 2 Once at the desired setpoint temperature, no further action is needed. The new setpoint temperature will be held until the next scheduled time period begins. For more information on schedule time periods, see “Program Schedule” on page 11. Temporary Hold 3 To cancel the Temporary Hold, Press + or - and then press Cancel.
RTH7400/RTH7500 Series Wiring—heat pump Connect wires: heat pump 1 2 Match each labeled wire with same letter on new thermostat. Insert the wires into the matching terminal. NOTE: If you have difficulty inserting wires, you may have to press down the terminal push button next to the corresponding terminal. Labels don’t match? If labels do not match letters on thermostat, see page 13. S S Y Y G C U U A L/A O/B W2 AUX E W K R Rc Alternate wiring (for heat pumps only) NOTES: 1.
Quick Installation Guide Advanced menu 1 Press and hold Menu and + buttons for approximately 5 seconds to enter advanced menu. 2 Press Select to enter System Setup (ISU) menu. 3 Press Select to cycle through System Setup numbers. NOTE: See “System Setup options” on page 8 for a full list of System Setup numbers and options. 4 Press + or - to change values or select from available options. 5 Press Select to save changes and advance to the next System Setup number.
RTH7400/RTH7500 Series Smart Response® Technology This feature allows the thermostat to “learn” how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set. For example: Set the Wake time to 6 am, and the temperature to 70°. The heat will come on before 6 am, so the temperature is 70° by the time you wake at 6. The message “Recovery” is displayed when the system is activated before a scheduled time period.
Quick Installation Guide Set the date 1 Press Menu to enter the device menu. You will see PROG. Press + or - to chose DATE. 2 3 Press Select. 4 Press + or - to adjust the month. Press Select. 5 Press + or - to adjust the day. Press Select to save and exit. You will see the year blinking. Press + or - to adjust the year. Press Select. Setting degrees Fahrenheit (F) or Celsius (C) 1 Press Menu to enter the device menu. You will see PROG. Press + or - to choose F/C. 2 3 4 Press Select.
RTH7400/RTH7500 Series 3 When the alert icon appears, check the error code with the table below to determine the problem. 4 Snooze the alert. 5 Dismiss the alert. Alerts codes Number Alert/Reminder Definition 170 Internal Memory Error The memory of the thermostat has encountered an error. Please replace the thermostat. 173 Thermostat Temperature Sensor Error The sensor of the thermostat has encountered an error. Please replace the thermostat.
Quick Installation Guide Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank If you’re using batteries, make sure fresh AA alkaline batteries are properly installed (see page 6). Cannot change system setting to Cool Check System Setup Option 220 to make sure the options are set to either 1 or 2 (see page 9).
RTH7400/RTH7500 Series 1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
CAUTION: ELECTRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect power before beginning installation. CAUTION: MERCURY NOTICE If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal. Customer assistance For assistance with this product, please visit http://yourhome.honeywell.com.
Serie RTH7400, RTH7500 Termostato programable Guía de instalación rápida Su caja incluye Guía de instalación rápida Tornillos y anclajes Termostato RTH7400/RTH7500 Sistema de montaje UWP™ (UWP) Herramientas que necesitará Herramientas que podría necesitar Destornillador de estrella Destornillador de hoja plana pequeño Alicates Lápiz Pinzas de punta Nivel Taladro y broca (7/32 pulg.
Guía de instalación rápida Remoción del termostato antiguo 1 Desconecte el suministro de energía eléctrica. Para protegerse usted y el equipo, desconecte el suministro de energía eléctrica desde la caja de interruptores de circuito o el interruptor que controla el sistema de calefacción/refrigeración. Encendido Apagado Apagado Interruptor Caja de interruptores de circuito Encendido 2 Verifique que el sistema se encuentre apagado. Cambie la temperatura en el termostato antiguo.
Serie RTH7400/RTH7500 5 Tome una foto de cómo se ve el cableado en este momento. Asegúrese de incluir las letras que se encuentran al lado de los terminales donde se insertan los cables. Esta será una referencia útil al cablear el termostato. Consejo: Si los cables se han decolorado o si 2 terminales tienen el mismo color de cable, use las etiquetas para cables que se suministran en el paquete para etiquetar cada cable. 6 Quite todos los puentes. Un puente conecta un terminal con otro.
Guía de instalación rápida 9 Desconecte los cables y quite la placa de pared antigua. Use un destornillador para quitar los cables de los terminales. A continuación, use etiquetas para cables a fin de identificar cada cable a medida que lo desconecta. La letra de la etiqueta para cables debe coincidir con la letra en el terminal. Consejo: Para evitar que los cables caigan en el hueco de la pared, enrósquelos alrededor de un lápiz.
Serie RTH7400/RTH7500 11 Inserte los anclajes de pared. Se recomienda que para el montaje del termostato use los anclajes de pared incluidos en la caja. Puede usar la UWP para marcar el lugar donde desea colocar los anclajes de pared. a) Nivele la placa de pared. b) Marque la ubicación de los anclajes de pared con un lápiz. c) Perfore los agujeros. d) Inserte los anclajes de pared. e) Asegúrese de que los tarugos queden a ras con la pared. Consejo: Use una broca para taladro de 7/32 pulgada.
Guía de instalación rápida 13 Conecte los cables del paso 8. Presione hacia abajo las lengüetas para insertar los cables en los agujeros de los terminales correspondientes en el UWP (un cable por terminal) hasta que quede firmemente en su lugar. Tire suavemente los cables paras verificar que estén seguros. Consejo: Si necesita aflojar los cables, presione hacia abajo las lengüetas terminales que están a los lados de la UWP. Este cableado es solo un ejemplo; el suyo puede variar.
Serie RTH7400/RTH7500 18 Encienda la energía eléctrica. Encienda la energía eléctrica desde la caja de interruptores de circuito o el interruptor que controla el sistema de calefacción/refrigeración. Encedido Encedido Apagado Interruptor Caja de interruptores de circuito Encedido Configuración de fecha y hora Apagado 19 Configure la fecha. Presione + o - para ajustar el año. Presione Select (Seleccionar). Presione + o - para ajustar el mes. Presione Select (Seleccionar).
Guía de instalación rápida Configuración del sistema 22 Seleccione las opciones de configuración del sistema. Presione + o - para cambiar los valores o seleccionar las opciones disponibles. Luego, presione Select (Seleccionar) para guardar los cambios y pasar al siguiente número de configuración del sistema. Consulte “Opciones de configuración del sistema” a continuación para obtener una lista completa de números y opciones de configuración del sistema.
Serie RTH7400/RTH7500 Número Descripción Opciones (las configuraciones predeterminadas de fábrica están en negrita) 218 Válvula de inversión O/B 0 = O (O/B en refrigeración) 1 = B (O/B en calefacción) Nota: Esta opción solo aparece si se configura la bomba de calor. Seleccione si la válvula de inversión O/B debe suministrar energía en refrigeración o en calefacción 220 Etapas de refrigeración / Etapas del compresor 200 = Conv.
Guía de instalación rápida Ajustes de funcionamiento del sistema 1 Presione el botón Mode (Modo) para continuar con el siguiente modo del sistema disponible. 2 Recorra los modos hasta que aparezca el modo del sistema requerido y déjelo para que se active. NOTA: Los modos del sistema disponibles pueden variar según el modelo y los ajustes del sistema. Modos del sistema: ‒‒ Auto (Automático): El termostato selecciona el sistema de calefacción o refrigeración según sea necesario.
Serie RTH7400/RTH7500 Cronograma del programa Heat Cool Puede programar cuatro períodos de tiempo por (Calefacción ) (Refrigeración ) día, con diferentes configuraciones para los días de Wake semana y los fines de semana. Recomendamos las ° ° configuraciones preestablecidas (que se muestran en (Despertar) (6:00 am) el cuadro que se encuentra a continuación), debido a Away que reducen los gastos de calefacción y refrigeración.
Guía de instalación rápida Anulación del cronograma del programa (temporal) 1 2 3 Presione + o - para ajustar la temperatura. Una vez obtenida la temperatura de referencia deseada, no se requieren otras acciones. La nueva temperatura de referencia se mantendrá hasta que comience el siguiente período programado. Para obtener información adicional sobre los períodos de horario programados, consulte “Cronograma del programa” en la página 11.
Serie RTH7400/RTH7500 Cableado: Bomba de calor Conexión de los cables: bomba de calor 1 2 Haga coincidir cada cable etiquetado con la misma letra en el termostato nuevo. Inserte los cables en el terminal correspondiente. NOTA: Si tiene problemas para insertar los cables, es posible que deba presionar el botón pulsador del terminal que se encuentra al lado del terminal correspondiente. ¿Las etiquetas no coinciden? Si las etiquetas no coinciden con las letras en el termostato, consulte la página 13.
Guía de instalación rápida Menú avanzado 1 Mantenga presionados los botones Menú y + durante aproximadamente 5 segundos para acceder al menú avanzado. 2 Presione Select (Seleccionar) para acceder al menú de Configuración del sistema (ISU). 3 Presione Select (Seleccionar) para recorrer los números de configuración del sistema. NOTA: Consulte “Opciones de configuración del sistema” en la página 8 para obtener una lista completa de números y opciones de configuración del sistema.
Serie RTH7400/RTH7500 Tecnología Smart Response® Esta característica permite que el termostato “sepa” cuánto demora su equipo de calefacción y su aire acondicionado en alcanzar las configuraciones de temperatura programadas, de manera que se alcance esa temperatura a la hora que usted la configuró. Por ejemplo: Configure la hora de despertarse a las 6 a.m. y la temperatura en 70 °F (21.1 °C). La calefacción se activará antes de las 6 a.m. para que la temperatura sea de 70 °F (21.1 °C) a las 6 a.m.
Guía de instalación rápida Configuración de fecha 1 Presione el botón Menu para ingresar al menú del artefacto. Usted verá PROG. Presione + o - para escoger DATE (FECHA). 2 3 Presione Select (seleccionar). 4 Presione + o - para ajustar el mes. Presione Select (seleccionar). 5 Presione + o - para ajustar el día. Presione Select (Seleccionar) para guardar y salir. Usted verá titilar el año. Presione + o - para ajustar el año. Presione Select (seleccionar).
Serie RTH7400/RTH7500 3 Cuando aparezca el ícono de alerta, verifique el código de error comparándolo con la tabla a continuación para determinar cuál es el problema. 4 Repetición de la alerta 5 Descarte de la alerta Códigos de las alertas Número Alerta/recordatorio Definición 170 Error de la memoria interna La memoria del termostato ha encontrado un error. Por favor reemplace el termostato. 173 Error del sensor de temperatura del termostato El sensor del termostato ha encontrado un error.
Guía de instalación rápida Localización y solución de problemas Si tiene dificultades con el termostato, intente seguir las sugerencias que se indican a continuación. La mayoría de los problemas se pueden solucionar de manera fácil y rápida. La pantalla está en blanco Si usa baterías, compruebe que las baterías alcalinas AA nuevas estén instaladas correctamente (consulte la página 6).
Serie RTH7400/RTH7500 Garantía limitada de 1 año Honeywell garantiza, por el período de un (1) año a partir de la fecha de compra por parte del consumidor, que este producto, sin incluir la batería, no presentará defectos en los materiales ni de mano de obra, en condiciones normales de uso y de servicio.
PRECAUCIÓN: PELIGRO DE ELECTROCUCIÓN Puede causar descargas eléctricas o daños al equipo. Desconecte el suministro eléctrico antes de comenzar la instalación. PRECAUCIÓN: AVISO SOBRE MERCURIO Si este producto está reemplazando a un control que contiene mercurio en un tubo sellado, no tire a la basura el control anterior. Contacte a la oficina de manejo de desechos de su localidad para averiguar la forma de reciclar y desechar adecuadamente el producto.