Installation Information

ManualsBrandsHoneywell ManualsDoorRCWL301A

69-2139EFS—03 1

RCWL301A Instruction Manual

Premium Portable Wirefree Chime with Push, Converter, and Door Contacts

Thank you for choosing this Honeywell product. Please use the following instructions

to ensure correct installation and use. Keep these notes in a safe place for future

reference.

Checking Pack Contents

Unpack your chime kit and identify the following parts:

• Chime (51360SL)

• Wall mounting bracket

• Bell push (51368SL)

• Bell push/converter/extender (51371SL)

• Door contacts

• 2x CR2032 battery for bell push and converter

• 4x mounting screws for door contacts

• 4x mounting screws for push/converter

• 2x mounting screws for chime

• 2x wall anchors

• 2x adhesive pads

• Bell wire (for use with converter and door contact)

• Self-adhesive icons

You will need:

• 3x LR6 ‘AA’ Alkaline batteries

• Phillips screwdriver

• Small flat bladed screwdriver

• 1/4-in. (6 mm) masonry drill

Safety

Before proceeding with the installation, please note the following safety warnings:

• Always follow the manufacturer’s advice when using power tools and wear suitable

protective equipment (e.g. safety goggles) when drilling holes, etc.

• Before drilling holes in walls, check for hidden electricity cables and water pipes.

The use of a cable/pipe locator is advisable if in doubt.

• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat

such as sunshine, fire or the like; danger of damage if battery is incorrectly

replaced. Replace only with the same or equivalent type.

Quick Start

The bell push and converter supplied with this kit are pre-programmed to operate with

the chime. You need to do the following to get started:

• Open the bell push and the converter

• Fit the push and converter batteries

• Fit the chime batteries

• Check the volume setting

When you operate the bell push and converter, the chime will sound and the icon will

flash.

To use the door contacts, you need to wire them to the converter. Please refer to

steps in Wireless Converter/Extender/Push and Door Contact for setup.

If you use an additional push and converter or you want to assign a different

icon to your push, you will need to follow the Programming Procedure.

Open the Bell Push

Insert a flat bladed screwdriver into the slot A at the base of the push. Carefully lever

the cover and base apart (Fig. 1).

Fit the Push Battery

Insert the CR2032 coin cell. Ensure the face marked ‘+’ is uppermost (Fig. 2).

Fit the Chime Batteries

To remove the chime battery cover, press at point B and slide the cover back 1/4 in. (5

mm), then lift off. Insert 3 x LR6 ‘AA’ alkaline batteries (not supplied). Observe polarity

as marked inside the battery compartment (Fig 3).

Sliding Window

Release the catch (B) and slide open the window (Fig. 4).

M27199

Fig. 1

M27153

CR2032

032

Fig. 2

M27200

Fig. 3

M27201

Fig. 4

Summary of content (8 pages)

PAGE 1
RCWL301A Instruction Manual Premium Portable Wirefree Chime with Push, Converter, and Door Contacts Thank you for choosing this Honeywell product. Please use the following instructions to ensure correct installation and use. Keep these notes in a safe place for future reference.
PAGE 2
Installation instructions–RCWL301A Volume Control The volume control is behind the sliding window on the front of the chime. Initially, set the control to mid-point. After you have tested your system, adjust to the desired volume (Fig. 5). VOLUME CONTROL Fig. 5 M27202 Use of Icons In addition to the chime sounds, your chime has a visual indication to show which device has activated it. An icon will illuminate when the chime is activated by the bell push, the converter or another compatible device.
PAGE 3
Installation instructions–RCWL301A Wireless Converter / Extender / Push and Door Contacts The converter can be used as a standalone wireless push or as an interface for door contacts. Open the bell push/converter Using a ball point pen press at point A shown in fig 8. Remove the cover. Undo the retaining screw B and remove the back of the push. B Fig. 8 A Use the push/converter/extender with door contacts Connect the push/converter/extender to the door contacts using the bell wire supplied.
PAGE 4
Installation instructions–RCWL301A Typical Connection C1 For C7 connection: Connect converter terminal 3 to the negative (-) terminal of the batteries in the wired chime and converter terminal 1 to the positive (+) terminal of the batteries in the wired chime. For C5 and C6 connections: Turn off power before connecting converter to transformer.
PAGE 5
Installation instructions–RCWL301A RCWL301A Manual de instrucciones Campanilla sin cables portátil de primera con pulsador, convertidor, y contactos para puerta Gracias por elegir este producto Honeywell. Por favor utilice las siguientes instrucciones para lograr la instalaciéon y uso adecuados del producto. Conserve estas notas en un lugar seguro para referencia futura.
PAGE 6
Installation instructions–RCWL301A Ventanilla deslizante Libere el enganche (B) y deslice la ventanilla para abrirla (Fig. 4). B M27201 Fig. 4 Control de volumen El control de volumen está detrás de la ventanilla deslizante al frente de la campanilla. Inicialmente, coloque el control a la mitad. Después de probar su sistema, regúlelo al volumen deseado (Fig. 5). CONTROL DE VOLUMEN Fig.
PAGE 7
Installation instructions–RCWL301A Abra el pulsador/convertidor del timbre Con un bolígrafo, presione en el punto A, tal como se muestra en la fig. 8. Quite la cubierta. Retire el tornillo de retención B y quite la parte posterior del pulsador. B A Fig. 8 Utilice el pulsador/convertidor/extensor con los contactos de puerta Conecte el pulsador/convertidor/extensor a los contactos de puerta utilizando el cable para timbre que se suministra.
PAGE 8
Installation instructions–RCWL301A Especificación Campanilla Pulsador del timbre/ Convertidor/Extensor Pulsador del timbre Temperatura de funcionamiento 32°F a 104°F (0ºC a 40ºC) 14°F a 104°F (-10ºC a 40ºC) 14°F a 104°F (-10ºC a 40ºC) Frecuencia RF-EE.UU./Canadá 916.8 MHz 916.8 MHz 916.