T9 THERMOSTAT Installation Guide Online Guides honeywellhome.
Read before installing.
Compatibility Section • REQUIRED: A C-Wire (common wire) is needed for 24 VAC power. If you do not have a C-Wire, then a C-Wire Adapter is provided. This guide will help you determine if you have a C-Wire or will need to use the included C-Wire Adapter (Step 10). The C-Wire is a wire that originates from your heating and cooling system and needs to be connected to the C terminal on your thermostat. There is no universal color used to designate this type of wire.
Removing your old thermostat You will need: Screwdriver, needle-nose pliers 1 Turn off power ON To protect your equipment, turn off the power at the breaker box or switch that controls you heating and cooling equipment. Note: The thermostat off switch will not turn off the power to the equipment. OFF OR OFF Switch Breaker box 2 Check that your system is off Change the temperature on your old thermostat so that your system starts heating or cooling.
Compatibility Check 4 Do you have a line voltage system? Line voltage systems have thick black wires with wire nuts or are labeled high voltage (120V or higher). YES Your system is not compatible. Call 1-855-733-5465 to find a proinstaller in your area. Wire nut Thick black wire NO Continue to the next step. 5 Take a picture of your existing wall plate’s wiring In order to capture all of the letters next to the terminals, be sure to take multiple pictures from different angles.
8 Write down the colors of the wires Check the boxes and write down the color of the wires connected to terminals that are coming from the wall. Check all that apply (not all will apply). Terminal ¨ ¨ ¨ ¨ ¨ ¨ ¨ Wire Color Terminal ¨ ¨ ¨ ¨ ¨ ¨ ¨ A or L/A C Required* E G K O/B U (1 or 2) Wire Color R Rc Rh W W2 or Aux Y Y2 *A C-wire or C-Wire Power Adapter (included) is required. If there are wires in terminals that are not listed, you will need additional wiring support. Visit honeywellhome.
Only complete this section if you answered No to Step 10 Connecting Your Unused C-Wire You will need: Screwdriver, flashlight, wire strippers Compatibility Check 11 Do you have a zoning panel? You have a zoning panel if you have multiple thermostats and one furnace or heating system. Furnace YES Thermostat C-Wire Adapter installation is more complicated on zoned systems. Call 1-855-733-5465 to find a pro-installer. Zoning Panel NO Proceed to the next step.
14 Remove cover from furnace or heating system Open the heating and cooling system’s cover to find the control board. You should see the same terminal labels that are on your thermostat. Note: You may need to unscrew the cover. The control board may be at the top or bottom. G C R W Y 15 Find the other end of the unused wire Locate the bundle of wires that are the same as the ones at your thermostat. The unused wire should be the same color as the one near your existing thermostat.
Installing Your New Thermostat You will need: Level, pencil, drill and a 7/32in drill bit Thermostat Screws UWP wallplate 9 Anchors Wall
18 Position wall plate Pull open the wall plate that was included with your new thermostat. Insert the bundle of wires through the back of the wall plate. - Make sure at least 1/4-inch of each wire is exposed for easy insertion into the wire terminals. UWP 19 Insert recommended wall anchors It is recommended that you use the wall anchors included in the box to mount your thermostat. You can use the wall plate to mark where you want to place the wall anchors.
20 Determine Correct R-Switch Position and Insert R-wire or wires Set the R-switch up or down based on your wiring notes in Step 8. Insert wires into the inner holes of the terminals on the wall plate. The tabs will stay down once the wire is inserted. If you have 1 R-Wire (R, RC, RH): 1. Ensure the right R-switch is in the up position. 2. Insert your R-wire (R, Rh or Rc) into R-terminal. OR If you have 2 R-Wires (R, RC, RH): 1. Set right R-switch to the down position. 2.
22 Close the door and mount the wall plate Mount the wall plate using the provided screws. Install all three screws for a secure fit on your wall. Tip: Prior to tightening the screws, use a level to ensure the wall plate is level. 23 Attach your thermostat Align the thermostat on the wall plate and firmly snap into place. Go back to your circuit breaker box. 24 Turn power back on Turn on the switch that controls your heating and cooling system.
Getting the most from the T9 Wi-Fi Thermostat Prioritize Rooms Prioritize a specific room or multiple rooms, or let comfort follow your move using built-in motion detection. Control on the Go Adjust your thermostat from anywhere using your tablet or smartphone. Save Energy With geofencing, you can save money on the most expensive part of your energy bill while you’re away. Simple Installation The thermostat automatically programs itself.
Using your thermostat The screen will wake up by pressing the center area of the displayed temperature. Indoor Temperature Displays the current indoor temperature. Current Priority Displays the type of priority and number of rooms being prioritized. Extend your thermostat’s reach with additional Wireless Room Sensors. Indoor Humidity Displays the current indoor humidity. 2 18% 74 Adjust Temperature Touch the up and down arrows to set your desired temperature.
Using Priority Priority creates an average temperature in your home based on specific rooms. This allows you to prioritize comfort where you want it. Selected Rooms Rooms you manually select create an average temperature in your home. 72 72 72 72 Unselected Room Will not contribute to the average temperature. Selected Room Will contribute to the average temperature. Active Rooms Rooms with detected motion are automatically selected to create an average temperature in your home.
Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • • • • Check circuit breaker and reset if necessary. Make sure power switch for heating & cooling system is on. Make sure furnace door is closed securely. Make sure the C wire is connected. Heating or cooling system does not respond • Press Menu > System Mode > Heat > Done to set the system to Heat mode.
2-year limited warranty Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of two (2) years from the date of first purchase by the original purchaser. If at any time during the warranty period the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option).
Resideo Inc., 1985 Douglas Drive North Golden Valley, MN 55422 www.resideo.com ©2018 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International Inc. 33-00421EF—01 M.S. 11-18 Printed in U.S.A.
THERMOSTAT T9 Guide d’installation Guides en ligne honeywellhome.
Lire avant l’installation.
Section sur la compatibilité • REQUIS : Un fil C (fil neutre) est requis pour l’alimentation 24 V c.a. Si vous n’avez pas de fil C, un adaptateur pour fil C est fourni. Ce guide vous aider à déterminer si vous disposez d’un fil C ou si vous devez utiliser l’adaptateur pour fil C (étape 10). Le fil C provient de votre système de chauffage et de climatisation et il doit être raccordé à la borne C de votre thermostat. Il n’y a aucune couleur universelle pour désigner ce type de fil.
Comment retirer votre ancien thermostat Matériel nécessaire : Tournevis, pince à bec long 1 Mettez l’alimentation hors tension. ON Pour protéger votre équipement, coupez l’alimentation au disjoncteur ou à l’interrupteur qui contrôle votre système de chauffage et de climatisation. Remarque : L’interrupteur de marche/arrêt du thermostat ne coupe pas l’alimentation à l’équipement. OFF OU OFF Interrupteur Panneau de disjoncteurs 2 Assurez-vous que votre système est éteint.
Vérification de compatibilité 4 Le thermostat est-il alimenté par la tension secteur? Les systèmes à tension secteur sont dotés de gros fils noirs avec capuchons de connexion ou munis d’une étiquette haute tension (120 V ou plus). OUI Votre système n’est pas compatible. Composez le 1 855 733-5465 pour trouver un installateur professionnel dans votre région. Capuchon de connexion Fil noir épais NON Passez à l’étape suivante. 5 Prenez une photo du câblage de votre plaque murale existante.
8 Inscrivez la couleur des fils. Cochez les cases et écrivez la couleur des fils raccordés aux bornes provenant du mur. Cochez toute les cases applicables (certaines ne sont pas utilisées). Borne ¨ ¨ ¨ ¨ ¨ ¨ ¨ Couleur du fil Borne ¨ ¨ ¨ ¨ ¨ ¨ ¨ A ou L/A C Requis* E G K O/B U (1 ou 2) Couleur du fil R Rc Rh W W2 ou Aux Y Y2 * Un fil C ou un adaptateur d’alimentation de fil C (compris) est requis.
Ne suivez cette section que si vous avez répondu Non à l’étape 10 Raccordement de votre fil C inutilisé Matériel nécessaire : Tournevis, lampe de poche, pince à dénuder Vérification de compatibilité 11 Disposez-vous d’un panneau de zonage? Vous disposez d’un panneau de zonage si vous avez plusieurs thermostats et un seul système de chauffage (ou chaudière). Thermostat OUI Tableau de commande de zonage Chaudière L’installation de l’adaptateur pour fil C est plus compliquée sur les systèmes zonés.
14 Retirez le couvercle du compartiment de la chaudière ou du système de chauffage. Ouvrez le compartiment du système de chauffage et de climatisation pour révéler le panneau de commande. Vous devriez y retrouver les mêmes étiquettes de borne que celles de votre thermostat. Remarque : Vous devrez peut-être utiliser un tournevis pour retirer le couvercle du compartiment. Le tableau de commande peut se trouver dans la partie supérieure ou inférieure. G C R W Y 15 Trouvez l’autre extrémité du fil inutilisé.
Installation de votre thermostat neuf Matériel nécessaire : Niveau, crayon, perceuse et mèche 7/32 po Thermostat Vis Plaque murale UWP 9 Ancrages Mur
18 Placez la plaque murale Ouvrez la plaque murale comprise avec votre thermostat neuf. Insérez le groupe de fils depuis l’arrière de la plaque murale. - Assurez vous de dégager au moins 6 mm (1/4 po) de chaque fil pour pouvoir les insérer facilement dans les bornes. UWP 19 Insérez les ancrages recommandés. Nous vous recommandons d’utiliser les ancrages inclus dans l’emballage pour installer votre thermostat. Vous pouvez utiliser la plaque murale pour marquer l’emplacement des ancrages.
20 Déterminez la position de l’interrupteur R et insérez le ou les fils R. Positionnez l’interrupteur R vers le haut ou vers le bas d’après les notes de branchement prises à l’étape 8. Insérez les fils dans les trous internes des bornes de la plaque murale. Les languettes resteront abaissées une fois le fil inséré. Si vous avez un (1) fil R (R, Rc ou Rh) : 1. Assurezvous que l’interrupteur R de droite est en position relevée. 2. Insérez votre fil R (R, Rh ou Rc) dans la borne R.
22 Fermez le cache et posez la plaque murale. À l’aide des vis fournies, posez la plaque murale. Pour assurer la solidité du montage au mur, posez les trois vis. Astuce : Avant de serrer les vis, utilisez un niveau pour vous assurer que la plaque murale est bien de niveau. 23 Fixez votre thermostat. Alignez le thermostat sur la plaque murale et enclenchez le fermement en place. Revenez à votre boîte de disjoncteurs. 24 Mettez l’alimentation sous tension.
Tirer le maximum du thermostat Wi-Fi T9 Prioriser les pièces Priorisez une ou plusieurs pièces, ou laissez le soin au système d’assurer votre confort grâce à la détection de mouvement intégrée. Contrôle à distance Réglez votre thermostat depuis n’importe où à l’aide de votre tablette ou téléphone intelligent. Économies d’énergie Avec la fonction Geofencing, vous pouvez économiser de l’argent sur votre facture énergétique lorsque vous êtes absent.
Utilisation de votre thermostat L’écran s’allume lorsque vous appuyez au centre de la zone de température affichée. Température intérieure Affiche la température intérieure actuelle. Priorité actuelle Affiche le type de priorité et le nombre de pièces qui en font l’objet. Étendez la portée de votre thermostat au moyen de détecteurs de pièce sans fil supplémentaires.
Utilisation de la fonction Priorité. La fonction Priorité crée une température moyenne dans votre maison en se basant sur des pièces précises. Ceci vous permet de prioriser le confort là où vous le voulez. Pièces sélectionnées Les pièces que vous sélectionnez manuellement créent une température moyenne dans votre maison. 72 72 72 72 Pièces non sélectionnées Ces pièces ne contribuent pas au calcul de la température moyenne. Pièce sélectionnée Cette pièce contribue au calcul de la température moyenne.
Dépannage Si vous rencontrez des difficultés avec votre thermostat, veuillez essayer les suggestions suivantes. La plupart des problèmes peuvent être corrigés rapidement et simplement. L’écran est vide • • • • Le système de chauffage ou de climatisation ne répond pas. • • • • • • Vérifiez le disjoncteur et réinitialisez-le si nécessaire. Veillez à ce que l’interrupteur du système de chauffage et de climatisation soit en position de marche.
Garantie limitée à deux ans Resideo garantit ce produit, à l’exception des piles, contre tout défaut de pièce ou de main-d’œuvre, durant une période pour deux (2) ans à partir de la date d’achat par le consommateur d’origine si le produit est utilisé et entretenu convenablement. En cas de défaillance ou de mauvais fonctionnement pendant la période de garantie, Resideo remplacera ou réparera le produit, à sa discrétion.
Resideo Inc., 1985 Douglas Drive North Golden Valley, MN 55422 www.resideo.com ©2018 Resideo Technologies, Inc. Tous droits réservés. La marque de commerce Honeywell Home est utilisée sous licence avec l’autorisation d’Honeywell International Inc. 33-00421EF—01 M.S.