Submittal Sheet

ManualsBrandsHoneywell ManualsDampersSpring Return Modulating Cartridge Globe Valve Actuator, 40.5 lb-f

PRODUCT DATA

62-0100-9

® U.S. Registered Trademark

M6410A,M7410F,M6435A,M7435F Actuators

V5852A, V5853A, V5862A, V5863A Valves

40.5 LB (180N) NON-SPRING AND SPRING RETURN ACTUATORS

AND 1/2 INCH, 3/4 INCH CARTRIDGE GLOBE VALVES

APPLICATION

M6410A and M7410F Series 1000 Non-Spring Return Valve

Actuators provide floating or modulating control of Series

1000 and 2000 V5852A, V5853A, V5862A and V5863A

Cartridge Globe Valves.

M6435A and M7435F Series 1000 Spring Return Valve

Actuators provide floating or modulating control of Series

1000 and 2000 V5852A, V5853A, V5862A and V5863A

Cartridge Globe Valves.

The actuators are used in electronic temperature control

systems, which use hot and/or cold water (with glycol up to

50 percent) as the controlled medium in variable air volume

(VAV) terminal units, fan-coil units, small reheaters and

recoolers.

The V5852A, V5853A, V5862A, V5863A Series 1000 and

2000 Cartridge Globe Valves can also be controlled by

MP958A Pneumatic Valve Actuators.

FEATURES

• Small size allows installation in limited space.

• Long stroke allows wider range of control.

Actuators

• Low power consumption.

• Synchronous motor.

• No mounting tools required (including the MP958).

• Low-maintenance plastic housing.

• Conduit connector standard.

• No separate linkage required.

• M64XXA provides 3-position floating control without

proportional feedback.

• M74XXF receives 0 to 10 Vdc or 2 to 10 Vdc input

signal, selectable at the site.

• M74XXF includes direct/reverse acting switch.

Non-Spring Return (M6410A, M7410F)

• Especially suitable for Excel

Controller or Individual

Room Controller (IRC) System.

• Internal valve position indicator.

• Magnetic coupling for torque limitation independent of

voltage supply, and self-adjustment of close-off port.

• Ready-to-wire connecting cable.

Spring Return (M6435A, M7435F)

• Force-limiting end switches.

• No calibration.

Valves

• V5852A is a two-way female sweat valve.

• V5853A is a three-way female sweat mixing valve.

• V5862A is a two-way female NPT valve.

• V5863A is a three-way female NPT mixing valve.

• Soft valve seat provides low leakage rate.

• Valve inserts are changeable without draining valve

when used with the insert replacement tool.

• Threaded plastic cover allows manual operation.

• Brass body and stainless steel stem.

Summary of content (8 pages)

PAGE 1
M6410A,M7410F,M6435A,M7435F Actuators V5852A, V5853A, V5862A, V5863A Valves 40.5 LB (180N) NON-SPRING AND SPRING RETURN ACTUATORS AND 1/2 INCH, 3/4 INCH CARTRIDGE GLOBE VALVES PRODUCT DATA FEATURES • Small size allows installation in limited space. • Long stroke allows wider range of control. Actuators • • • • • • • Low power consumption. Synchronous motor. No mounting tools required (including the MP958). Low-maintenance plastic housing. Conduit connector standard. No separate linkage required.
PAGE 2
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES SPECIFICATIONS IMPORTANT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, an individual unit may not exactly match the listed specifications. Also, this product is tested and calibrated under closely controlled conditions and some minor differences in performance can be expected if those conditions are changed. Models: M6410A: Non-Spring Return Valve Actuator.
PAGE 3
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES Actuator Required: M6410A: Non-Spring Return Valve Actuator (3-position floating). M6435A: Spring Return Valve Actuator (3-position floating; stem retracts upon power failure). M7410F: 0 to 10 Vdc or 2 to 10 Vdc Electronic Actuator, or M7435F: Spring Return Valve Actuator (modulating control; stem retracts upon power failure). MP958: Pneumatic Valve Actuator. Valve inserts are provided as spare parts. See Table 2.
PAGE 4
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES Table 2. Valve Insert Replacement Parts. Diameter (in.) For Valve Cv Part Number Interchangeable With Two-Way 1/2 3/4 V5852A2007, V5862A2005 0.19 0902812 0902809, 0902810, 0902811 V5852A2015, V5862A2013 0.29 0902811 0902809, 0902810, 0902812 V5852A2023, V5862A2021 0.47 0902810 0902809, 0902811, 0902812 V5852A2031, V5862A2039 0.74 0902809 0902810, 0902811, 0902812 V5852A2049, V5862A2047 1.
PAGE 5
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES CAUTION Electrical Shock or Equipment Damage Hazard. Can shock individuals or short equipment circuitry. Disconnect power supply before installation. CAUTION Sweat Valve Damage Hazard. Soldering the valve with the cartridge in place can damage the device. Prior to attaching valve to piping, remove cartridge from potential exposure to heat. M8228A Fig. 4. Removing protective cover from valve.
PAGE 6
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES Use the M7410F, M7435F with Excel® 5000/500/100/80 or T7984 Controllers. Power the M7410F from the same transformer as the controller. See Fig. 9 and 10. Electrical installation must comply with wiring diagram shown in Fig. 7. W7751D,F SUBBASE 1 = RED = COM ( ) 9 10 11 12 M6435 OPEN CLOSE 24 VAC COMMON T6984F OUT 8 8 OUT 7 7 OUT 6 6 OUT 5 5 OUT 3 4 OUT 4 3 CLOSED SIGNAL OUT 2 2 OPEN SIGNAL 1 OUT 1 Fig. 7.
PAGE 7
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES Switch Selection (M7435F) = 0 / 2 ... 10V The two built-in selector switches must be set according to the desired valve action and the controller output signal (0 to 10V or 2 to 10V). See Fig. 13. W2 24 V 1 W1 2 3 10V 2 ... 10V 0 ... 10V 10V M22023 Fig. 13. Switch selection according to controller output signal and valve type (two-way or three-way). = 0 / 2 ...
PAGE 8
M6410A,M7410F,M6435A,M7435F ACTUATORS V5852A, V5853A, V5862A, V5863A VALVES CHECKOUT INLET INLET + – + – OUTLET Valve OUTLET M5357A Fig. 15. Two-way valve operation block diagram. AB + – A B AB IMPORTANT Operating the system through one complete cycle is recommended to verify that the valve and actuator function properly. + – A Check Body and Connections for Leaks Before installing actuator, make sure that the valve stem operates freely by using the protective cover/manual handle.