Brochure

ManualsBrandsHoneywell ManualsDampersModutrol IV Motor, w/ 1 Internal Auxiliary Switch (24/120/230V)

410 70-6910

Modutrol IV Motors

Modutrol IV™ Family of Motors “Contractor-Friendly” design for

service and retrot

M27252

INTERNAL

FIELD-ADDABLE

AUXILIARY

SWITCHES

INTERNAL

FIELD-ADDABLE

TRANSFORMER

CRANK

ARM

RESISTOR

BOARD

CONTROLLER

INTERFACE

MODULE

Honeywell Modutrol IV motors, your reliable replacement business

solution. Built for decades, with proven durability bringing exceptional

performance and technology to meet demanding applications

everywhere.

Features and benets:

1. Dual shafts. Slotted and tapped at both ends. Both drive and

auxiliary shafts have equal torque ratings, allowing auxiliary shaft

to drive full torque loads. This provides a more exible motor. For

example, a spring-return, normally closed motor will provide normally

open operation simply by using the auxiliary shaft.

2. NEMA 3 housing. Modutrol IV™ motor housings protect the

motor from driving rain if motor is mounted in the upright position

(as shown in above photo). May be mounted outdoors without a

weatherproong kit.

3. Brushless DC sub motor provides a xed torque over the entire

voltage range.

4. Reduced power consumption. Motor power needs can always be

satised with a 20 VA transformer.

5. Internal design. Results in improved performance and longer life.

• Microprocessor based technology eliminates the need for

mechanical end stops.

• Brushless DC sub motor eliminates the need for oil.

6. Auxiliary Switch cams. All models have auxiliary switch cams that

permit acceptance of 220736A, B Internal Auxiliary Switch Kits.

7. Field Adjustable stroke. Most models are eld adjustable (i.e. 90 to

160 degrees).

TRADELINE motors and appropriate accessories can be congured

to replace all previous Honeywell Modutrol motors, as well as most

OEM Modutrol motors. The appropriate accessories are listed with the

different models and in tables near the end of this section.

Summary of content (35 pages)

PAGE 1
Modutrol IV Motors Modutrol IV™ Family of Motors “Contractor-Friendly” design for service and retrofit INTERNAL FIELD-ADDABLE TRANSFORMER INTERNAL FIELD-ADDABLE AUXILIARY SWITCHES RESISTOR BOARD CONTROLLER INTERFACE MODULE M27252 CRANK ARM Honeywell Modutrol IV motors, your reliable replacement business solution. Built for decades, with proven durability bringing exceptional performance and technology to meet demanding applications everywhere. 3.
PAGE 2
Modutrol IV Motors Commercial Components Modutrol IV™ Family of Motors The following Modutrol IV™ motors can replace the old style Modutrol motors as shown below.
PAGE 3
Modutrol IV Motors The Honeywell Family of Modutrol IV™ Motors Actuator Voltage Vac Stroke 24a 120 230 Timing *TRADELINE models.
PAGE 4
Modutrol IV Motors Voltage Vac Stroke 24a 120 230 Timing Control Input On/Off SPDT Modulating Floating *TRADELINE models.
PAGE 5
Modutrol IV Motors M4185 Line Volt; M8185 Low Volt Two-Position Modutrol IV™ Motors Series 41 and Series 81 Modutrol IV motors are 2-position (lineand low-voltage per motor control) spring-return motors. They are used to operate dampers or valves in applications where it is necessary or desirable to have the controlled element return to the starting position in the event of power failure or interruption.
PAGE 6
Modutrol IV Motors Commercial Components Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 4-5/8 (116) 5-1/2 (140) 5-13/16 (148) 2-5/16 (58) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 1/4 (7) 13/16 (20) 2 4-1/16 (103) 4-7/8 (124) 1-1/2 (37) 5-9/16 (141) 5-1/2 (140) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR 6-7/16 (164) AUXILARY END POWER END 5-3/8 (137) 2-9/16 (66) 9/16 (15) 2 FOR 60 LB-IN. SPRING RETURN MODELS (SHOWN).
PAGE 7
Modutrol IV Motors M6184; M6194 Floating Modutrol IV™ Motors Series 61 Modutrol IV™ Motors non-spring return floating control motors are used with controllers that provide a switched SPDT or floating output to operate dampers or valves.
PAGE 8
Modutrol IV Motors Torque Rating (lb-in.) M6194D4003/U 300 lb-in. M6194E1006/U Torque Supply Timing, Rating Voltage Nominal (Nm) 34 Nm 24V 120 - 240 sec 300 lb-in. 34 Nm 24V Internal Auxiliary Switch 0 120 - 240 sec 1 Stroke Factory Stroke Setting 160 degrees Adjustable; 90 to 160 degrees, Symmetrical 90 degrees Adjustable; 90 to 160 degrees, Symmetrical Internal Transformer Weight Includes None 6.5 lb None 6.
PAGE 9
Modutrol IV Motors M6284; M6294 Floating Modutrol IV™ Motors, for Slaving Applications only These Series 62 Modutrol IV™ Motors non-spring return floating control motors are used with controllers that provide a switched SPDT or floating output to operate dampers or valves. These motors also have an internal electrically isolated feedback potentiometer that provides indication of the motor shaft position. Some models can be used for slaving Series 90 Motors.
PAGE 10
Modutrol IV Motors Torque Rating (lb-in.) M6294D1008-S/U 300 lb-in. 24V Stroke Tradeline Factory Value Stroke Setting Tradeline 160 degrees Adjustable; 90 to 160 degrees, Symmetrical Internal Weight Includes Internal Electrical Auxiliary Connections Transformer Switch None 6.
PAGE 11
Modutrol IV Motors M6285 Floating Modutrol IV™ Motors, for Slaving Applications only Series 62 Modutrol IV™ Motors are spring return floating control motors are used with controllers that provide a switched SPDT or floating output to operate dampers or valves. These motors also have an internal electrically isolated feedback potentiometer that provides indication of the motor shaft position and can be used for slaving Series 90 motors or rebalancing an external control circuit.
PAGE 12
Modutrol IV Motors Commercial Components Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 13
Modutrol IV Motors M6274; M6284; M6285; M6294 Modutrol IV™ Motor with Linear 10K feedback Series 62 Modutrol IV™ Motors Spring Return and Non-Spring Return floating control motors are used with controllers that provide a switched SPDT or floating output to operate dampers or valves. These motors also have an internal electrically isolated feedback potentiometer that provides indication of the motor shaft position.
PAGE 14
Modutrol IV Motors Commercial Components Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 15
Modutrol IV Motors M7164 Modutrol IV™ Motors Series 71 Modutrol IV™ Motors non-spring return motors are used to control dampers and valves. These motors accept a voltage signal from an electronic controller to position a damper or valve at any point between open and closed.
PAGE 16
Modutrol IV Motors Commercial Components Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 17
Modutrol IV Motors M7274; M7284; M7294 Modutrol IV™ Motors The Series 72 Modutrol IV Motors spring return and non-spring return motors are used to control dampers and valves. The motors accept a current or voltage signal from an electronic controller to position a damper or valve at any point between open and closed.
PAGE 18
Modutrol IV Motors Torque Rating (lb-in.) Torque Supply Timing, Internal Factory Rating Voltage Nominal Auxiliary Stroke (Nm) Switch Setting Stroke Control Signal Electrical Power Weight Internal Comments Connections Consumption Transformer Commercial Components Material Number Includes M7284Q1009/C 150 lb-in. 17 Nm 120V 30 - 60 sec 2 90 degrees Adjustable; 90 to 160 degrees, Symmetrical Modulating, Screw 4-20 mA terminals Driving – 15 VA 7.
PAGE 19
Modutrol IV Motors Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 20
Modutrol IV Motors Series 72 Modutrol IV™ Motors are spring return and non-spring return motors (per motor type) used to control dampers and valves. The motors accept a current or voltage signal from an electronic controller to position a damper or valve at any point between open and closed.
PAGE 21
Modutrol IV Motors Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 22
Modutrol IV Motors Proportional, spring-return motors for use with Honeywell W7080 panel 14-17 Vdc output; with minimum position adjustment.
PAGE 23
Modutrol IV Motors Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 1/4 (7) 13/16 (20) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 24
Modutrol IV Motors Series 90 Modutrol™ IV Motors are non-spring return modulating proportional control motors used with controllers that provide a Series 90 output to operate dampers or valves.
PAGE 25
Modutrol IV Motors Material Number Torque Power Timing, Rating Consumption Nominal (Nm) Internal Factory Auxiliary Stroke Switch Setting Shaft Rotation Electrical Internal Weight Includes (upon control Connections Transformer signal increase) M9174C1025/U 75 lb-in. 8.5 Nm Driving – 12 VA 30 - 60 sec 2 90 degrees Clockwise (as viewed from power end) (normally closed) Quickconnect terminals 50004263003 7.5 lb Transformer 120V Adjustable; 90 to 160 degrees, Asymmetrical M9174C1033/U 75 lb-in.
PAGE 26
Modutrol IV Motors Torque Rating (lb-in.) M9194E1000/U 300 lb-in. Torque Power Timing, Rating Consumption Nominal (Nm) Internal Factory Auxiliary Stroke Switch Setting Shaft Rotation Electrical Internal Weight Includes (upon control Connections Transformer signal increase) Supply Tradeline Stroke Voltage Value 34 Nm 1 Clockwise (as viewed from power end) (normally closed) 24V Driving – 15 VA 120 - 240 sec 90 degrees Quickconnect terminals None 6.
PAGE 27
Modutrol IV Motors Dimensions in inches (millimeters) TOP VIEW OF BRACKET ONLY 4-7/32 (107) 4-7/8 (124) 3-15/16 (100) 5-13/16 (148) 5-1/2 (140) 2-5/16 [58] 7/16 (11) 25/32 (20) POWER END 25/32 (20) 1/2 (13) 1/4 (7) 31/32 (24) 1/4 (7) 5/8 (16) 3 4 4-1/16 (103) 1-1/2 (38) 1-15/32 (37) 4-7/8 (124) 5-3/8 (136) 1 WIRING BOX 3/4 (19) BASE MOTOR POWER END AUXILARY END 6-15/32 (164) 5/32 (4) 5-13/32 (137) 1-3/4 (44) 2-19/32 (66) 1-1/4 (32) 2-1/2 (64) 19/32 (15) 2 ADAPTER BRACKET 3/4 (1
PAGE 28
Modutrol IV Motors Series 90 Modutrol IV™ Motors are spring return modulating proportional control motors used with controllers that provide a Series 90 output to operate dampers or valves.
PAGE 29
Modutrol IV Motors Dimensions in inches (millimeters) TOP VIEW TOP VIEW OF BRACKET 4-7/8 (124) 4-1/4 (107) 5-1/2 (140) 4-5/8 (116) 2-5/16 (58) 5-13/16 (148) 11/16 (17) POWER END 13/16 (20) 1/4 (7) 2 3 4-1/16 (103) 13/16 (20) 1/4 (7) 4-7/8 (124) 1-1/2 (37) 5-1/2 (140) 5-9/16 (141) 1-1/2 (37) JUNCTION BOX 3/4 (19) MOTOR AUXILIARY END POWER END 6-7/16 (164) 5-3/8 (137) 2-9/16 (66) SPRING RETURN MODEL SHOWN 1 FOR 60 LB-IN. SPRING RETURN MODELS 8-3/4 (222).
PAGE 30
Modutrol IV Motors Commercial Components Foot Mounted Motor Accessories Material Number Description Used With 203709D2/U Screw Terminal Adapter for Series 70 Mod IV Motors with Adjustable Zero and Span Series 2 and Series 3 Modutrol IV™ motors 220738A/U Adapter Bracket.
PAGE 31
Modutrol IV Motors 198162 Internal Transformer for Series 1 Motors Application: Internal Transformer Ambient Temperature Range: 0°F to 131°F (-18°C to +55°C) Material Number Supply Voltage 198162AA/U 120 or 208 or 240 SPST, On/Off Vac at 50 or 60 Hz switch Control Signal Includes Transformer, screws, instructions for mounting internally in Modutrol IV Series 1 motors For Mod IV Series 2 and 3 actuators, use 50017460-001 Comments 198162EA/U 120 Vac at 50 or 60 Hz SPST, On/Off switch For Mod IV Seri
PAGE 32
Modutrol IV Motors Controls from one to four Modutrol (Series 90) motors from one master motor. • Compatible with Modutrol III and Modutrol IV motors. • Mounts on master motor and operates controlled motors in unison or in sequence. • Controls motors with mechanical balance relay and solid state drive circuit. • Use with 24V motors. Application: Electro-mechanical Mounting: External mount to Modutrol IV Motors Approximate, Dimensions: 3 3/16 in. high x 3 1/4 in. wide x 3 3/8 in.
PAGE 33
Modutrol IV Motors Q607 Auxiliary Switches for Modutrol Motors For control of auxiliary equipment as a function of Modutrol motor shaft position. • Compatible with Modutrol III and Modutrol IV motors. (Requires 220738A adapter bracket for use with Modutrol IV motors). • Micro Switch precision switches, adjustable. • Indicate motor position by use of a scale plate anchored to a common shaft, which allows Q607 to be adjusted for operational sequence before mounting.
PAGE 34
Modutrol IV Motors For converting Series 90 Modutrol IV motors to Series 70 (electronic) control.
PAGE 35
Kit Mounted Motors M436; M836 Damper Motors Spring return motors for two-position back draft, outdoor air changeover, zone or minimum position damper control. • Operate outdoor air dampers for combustion or makeup air in residential and light commercial applications. • Operate changeover dampers for heating and cooling systems. • Operate minimum position dampers for ventilation and similar applications.