Instructions / Assembly

ManualsBrandsHoneywell ManualsHeater AccessoriesAqua-Stat

L6006 and L6007

Aquastat

Controllers

Installation Instructions for the Trained Service Technician.

Application

These Aquastat

Controllers operate in response to tem-

perature changes in hydronic heating systems. They provide

spdt switching for three-wire applications.

The L6006A,B, and L6007A combine low or high limit

and circulator control; L6006C combines circulator control

with low and high limit.

The L6006A,B are for horizontal insertion; the A model

uses an immersion well; the B model uses a capsule com-

pression fitting for direct immersion. The L6006C is for

horizontal or vertical surface mounting. The L6007A is for

horizontal or vertical insertion using an immersion well.

If immersion well or capsule compression fitting must be

ordered, refer to form 68-0040, Wells and Fittings for Tem-

perature Controllers, for part numbers and ordering informa-

tion.

ELECTRICAL RATINGS (A):

2. Check the ratings given in the instructions and on the

product to make sure the product is suitable for your applica-

tion.

3. Installer must be a trained, experienced service techni-

cian.

4. After installation is complete, check out product op-

eration as provided in these instructions.

WARNING

CAN CAUSE PROPERTY DAMAGE,

SEVERE INJURY OR DEATH.

This product is intended for use only in systems

with a pressure relief valve.

CAUTION

Disconnect power supply before connecting wir-

ing to prevent electrical shock or equipment

damage.

IMPORTANT: Controller can be used with or without

immersion well. If used, well must snugly fit sensing

bulb for good thermal response. Bulb should be in-

serted until it rests against bottom of well, and then

held there while the tubing clamp is tightened.

NOTE: Some models have an adjustable tubing length to 3

in. (76 mm). In these models, extra tubing inside the case

can be pulled out, if needed. See Fig. 1.

The manufacturer usually provides a tapping for insertion

of the controller sensing element. This tapping is located at a

point where typical water temperature can be measured.

Depending on model, the element is inserted in an immer-

sion well or directly immersed through a capsule compres-

sion fitting.

Follow the instructions furnished by the system manufac-

turer, if available; otherwise, refer to the appropriate follow-

ing procedure.

Installation

WHEN INSTALLING THIS PRODUCT...

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazardous condi-

tion.

l20 Vac 240 Vac

Full Load 8 5.1

Locked Rotor 48 30.6

Inductive Current 0.25 at 1/4 to 12 Vdc

SENSING ELEMENT IS FACTORY FORMED FOR 1.5 INCH

INSULATION WELL ASSEMBLIES.

FOR 3 INCH INSULATION WELL ASSEMBLIES, PULL OUT

SUFFICENT CAPILLARY TO ASSURE THAT THE CAPSULE

BOTTOMS IN THE WELL.

STRAIGHTEN CAPILLARY SUFFICENTLY SO IT DOES NOT

CAUTION:

EXCESSIVE HANDLING OR SHARP BENDS

CAN DAMAGE THE CAPILLARY.

Fig. 1—Adjusting the capillary length.

INTERFERE WITH INSERTING THE CAPSULE INTO THE WELL.

M8882

INSTALLING IMMERSION WELL MODELS

(L6006A, L6007A)

On existing installation, shut off the power and remove

the old control. If the old immersion well appears suitable,

and the adapter clamp on the Aquastat

Controller fits the

old well spud, do not replace.

1. If the system is filled, drain system to a point below the

boiler tapping.

Summary of content (4 pages)

PAGE 1
L6006 and L6007 Aquastat Controllers ® Installation Instructions for the Trained Service Technician. Application These Aquastat® Controllers operate in response to tem perature changes in hydronic heating systems. They provide spdt switching for three-wire applications. The L6006A,B, and L6007A combine low or high limit and circulator control; L6006C combines circulator control with low and high limit.
PAGE 2
. Remove plug (or old well) from boiler tapping. 3. Install the immersion well included with the control ler. If boiler tapping is greater than 1/2 in., use a reduction fitting to adapt the boiler opening to the 1 in. threads that are standard with the well or fitting. Fittings with 3/4 in. threads are also available. 4. Fill the system. Make sure that the well is screwed in tightly enough to prevent leakage.
PAGE 3
Adjustment Fig. 4—Mounting L6006C on pipe or tank. Set the differential to correspond with the boiler manufacturer recommendations. To adjust models with adjustable differential, rotate the wheel on the back of the snap switch until the desired reading is aligned with the V notch in the frame. The wheel provides an adjustment from 5°F to 30°F (3°C to 17°C). Replace the cover on the Aquastat® Controller. Adjust control point to correspond with the boiler manu facturer recommendations.
PAGE 4
Checkout Fig.6—Typical wiring hookup using L6006 and L6007 with L8148A. SERIES 80 THERMOSTAT 1 L6006, L6007 CIRCULATOR AND LOW LIMIT CONTROL R 2 L2 L1 (HOT) L1 W 3 B B R L2 T T Check to make certain that the Aquastat® Controller is installed and adjusted properly. Put the system into operation and observe the action of the device through several cycles to make certain that it provides proper low and/or ligh limit and circulator control.