Revision USER MANUAL IM11-PRT RFID MODULE MODEL NO:IM11-PRT RFID MODULE Honeywell Confidential and Proprietary
Table of Contents Introduction ....................................................................................................... 1 Technical Specifications ................................................................................... 3 Mechanical Integration ...................................................................................... 7 Electrical Integration ......................................................................................... 8 Power Requirements...................
Chapter Introduction This document specifies the details for a IM11-PRT RFID MODULE About IM11 IM11-PRT RFID Reader Module is designed for quick integration into computers, printers, and any other products that need to be RFID-enabled.
module is delivered. • Covers UHF bands from 865 to 928 MHz Supports four channel operation over the 865 to 868 MHz band. • Supports 50 channels in the FCC band from 902 to 928 MHz. • Supports the ISO 18000-6c protocol (EPC Class 1, Gen 2) • Supports the BRI (Basic Reader Interface) host communication protocol.
Chapter Technical Specifications Physical Specifications Specification Values Physical 50.95 mm long x 30 mm wide x 4.76 mm thick Weight Environmental Specifications Specification Values Operating Temperature -20 °C to +60 °C Storage Temperature -40 °C to +70 °C Humidity 25 °C to 60 °C, 0% to 95% relative humidity, non-condensing process Shock 2000 g, 0.5 ms pulse, 10 times on each axis Vibration GRMS. 10 to 500 Hz, in 3 axis ESD Passes CE mark requirements.
Transmitter Specifications Specification Minimum Typical Maximum Unit Notes Frequency Stability Spurious Emissions FCC Spurious Emissions ETSI -20 +20 PPM -55 -50 dBc dBc -54 dBm Out of band 4 In band Out of band
Thermal Shutdown Thermal Recovery 85 °C 75 °C As measured by sensor on module Transceiver Specifications Specification Values Output Power Control 29.5 dBm. User adjustable in 1 dB down to 10.5 dBm. Tolerance drift from +0.5 to -0.7. Bus Interface (USB or serial) USB 2.0 compliant client 12 Mbps (full speed) Serial 115.
tags) 50 tags per second (using over air tags) Performance Testing AD 223 tags on cardboard Receiver Specifications Receiver Input Values Sensitivity Typical: -70 dBm 15 dB return loss Maximum Reverse Input Power Maximum: +20 dBm 6
Mechanical Integration The module fits within the Mini PCI Express specifications. For physical dimensions, see the illustration.
Electrical Integration The module communicates either over USB or through serial: The USB client communication follows the CDC profile and is USB 2.0compliant, operating at 12 Mbps (full speed). In Serial mode, the module communicates as a standard PC COM port, operating at 115.2 Kbps. It has eight general purpose inputs and outputs for monitoring and controlling external signals. A Digital Signal Processor (DSP) controls the radio functions and provides communication with the host.
To reduce power, the module duty cycles its transmitter. The duty cycling happens according to the read commands that the application executes. To achieve the lowest power, after all tags are read, the transmitter turns off. After a period of time, the transmitter activates to identify new tags in the field. After all new tags are read, the transmitter turns off for the rest of the period.
Supported Antennas: These antennas are approved to work with iM11: Compact Yagi (6.0 dBi Linear) Microstrip Antenna, "Coupler” with -19.
Chapter Mini-PCI Connector Pin Descriptions Pin Descriptions Pin Pin Name Description 1 Reserved Do NOT connect 2 +V_BATT Power input 3 Reserved Do NOT connect 4 GND Ground 5 No Connect Not connected 6 GPIO2 7 No Connect Not connected 8 No Connect Not connected 9 GND Ground 10 No Connect Not connected 11 No Connect Not connected 12 No Connect Not connected 13 Reserved Do NOT connect 14 No Connect Not connected 15 GND Ground 16 GPIO0 17 Reserved Do NOT conn
26 GND Ground 27 GND Ground 28 GPIO1 29 GND 30 GPIO3 31 Reserved 32 GPIO4 33 RESET_L Logic low level resets IM11 34 GND Ground 35 GND Ground 36 USB_DM USB data minus 37 GND Ground 38 USB_DP USB data plus 39 +V_BATT Power input Ground Do NOT connect 40 GND Ground 41 +V_BATT Power input 42 No Connect Not connected 43 GND Ground 44 GPIO5 45 HOST_CTS1 46 GPIO6 47 HOST_RTS1 Future use Future use 48 GPIO7 49 HOST_RX1 Output.
Input and Output Voltage Level Descriptions Transmit Power The module is able to adjust transmit power from 29.5 dBm to10.5 dBm, configurable in 1 dB steps with an accuracy (the measure of the power output for each level) of +/-0.5 dB. The initial tolerance (the measure of the power output for each level) is +/-0.5 dB. The output power is set on each of the antennas. Output power tolerance from the nominal setting is +/- 0.75 dB over an ambient temperature range of -20 °C to 60 °C.
Chapter Agency Approvals FCC Communications commission interface statement Model: IM11PRT FCC ID: HD5-IM11R This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including, an interference that may cause undesired operation.
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Industry Canada Model: IM11PRT IC: 1693B-IM11R This device complies with ISED's license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux RSS exemptés de licence de l’ISED.
DETACHABLE ANTENNA USAGE This radio transmitter (IC: 1693B-IM11R/ Model: IM11-PRT) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil est destiné uniquement aux intégrateurs OEM dans les conditions suivantes : (Pour l’utilisation du module) 1) L’antenne doit être installée de telle sorte que 20cm soit maintenu entre l’antenne et les utilisateurs. 2) Le module émetteur ne peut pas être co-localisé avec un autre émetteur ou antenne. Tant que 2 conditions ci-dessus sont remplies, un autre test d’émetteur ne sera pas nécessaire.
End Product Labeling: This transmitter module is authorized only for use in devices where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: “Contains IC: 1693B-IM11R”. Étiquetage final des produits : Ce module émetteur n’est autorisé que pour une utilisation dans les appareils où l’antenne peut être installée de telle sorte que 20cm peut être maintenu entre l’antenne et les utilisateurs.
