Mini-Split Air Conditioner Single Zone Installation and Operations Manual HWAC-1217S HWAC-1817S HWAC-2417S Professional Installation Required! Please read and retain these instructions.
CONTENTS Thank you for purchasing the HWAC-1217S, HWAC-1817S, or HWAC-2417S Mini-Split Air Conditioner. This manual will provide you with safety information, installation steps, instructions for optimal use, and proper care and maintenance for your product. Please read this manual carefully before operating.
SPECIFICATIONS MODEL HWAC-1217S HWAC-1817S HWAC-2417S Cooling Capacity Heating Capacity 12,000 BTU Cooling 12,300 BTU Heating 18,000 BTU Cooling 18,000 BTU Heating 24,000 BTU Cooling 24,000 BTU Heating SEER Rating 17 17 17 Room Size (Sq. ft.) 300-500 600-800 900-1,200 Voltage / Frequency 115V / 60 Hz 230V / 60 Hz 230V / 60 Hz Dehumidification 2.11 pnt/h 3.38 pnt/h 6.
SAFETY INSTRUCTIONS - INSTALLATION Always be careful when using the machine. To reduce the risk of fire, electrical shock, or other injuries, keep these safety considerations in mind when installing, using, and maintaining your machine. . WARNING 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. The air conditioner must be properly grounded on a level surface. Do not connect the grounding wire to the gas pipeline, water pipeline, lightning rod, or telephone grounding wire.
SAFETY INSTRUCTIONS - INSTALLATION Always be careful when using the machine. To reduce the risk of fire, electrical shock, or other injuries, keep these safety considerations in mind when installing, using, and maintaining your machine. . CAUTION 1. 2. 3. 4. 5. 6. 7. Do not open windows and doors for a long time when the air conditioner is running. This will cause the cooling or heating capacity to be weakened. Do not stand /sit on top of the outdoor unit and do not place heavy items on it.
PRODUCT VIEW Indoor Unit, Open view 1. 2. 3. 4. 5. 6. 7. Air Inlet Grille Panel 1 Air Filter 2 Air Louvre Air Vent Force Switch Pipe Protector Ring 6 7 3 4 5 Outdoor Unit 1. 2. 3. 4.
NOTICE FOR INSTALLATION Important Notices • • • Before installing, please contact a local HVAC professional. If the unit is not installed by a registered HVAC contractor, the warranty will be voided. Please request a copy of the HVAC contractor’s invoice at the end of installation and keep for your records. The air conditioner must be installed by professionals according to the national wiring rules and this manual.
NOTICE FOR INSTALLATION Electrical Safety Requirements • • • • • • Be sure to use the rated voltage and air conditioners dedicated circuit for the power supply, and the power cord diameter must meet the national requirements. When the maximum current of air conditioner is ≥ 16A, it must use the air switch or leakage protection switch equipped with protection devices. The normal operating range is 90%-110% of the local rated voltage.
NOTICE FOR INSTALLATION Requirements for Operations at Raised Height • When carrying out installation at 6.6 ft. or higher above the base level, safety belts must be worn and ropes of sufficient strength be securely fastened to the outdoor unit, to prevent falling that could cause personal injury or death as well as property loss. Grounding Requirements • • • The air conditioner is the type I electrical appliance and must ensure a reliable grounding.
INSTALLATION: INDOOR UNIT Clearance Requirements for Indoor Installation 5.9 in 7.9 in 7.9 in 78.7 in NOTE: All measurements should be no less than posted from obstructions. Mounting Plate 1. 2. 3. The wall for installation of the indoor unit shall be hard and firm to prevent vibration. Use the “+” type screw to fasten the mounting plate. Horizontally mount the mounting plate on the wall and ensure it is level with the wall. Pull the mounting plate by hand after installing to confirm if it is solid.
INSTALLATION: INDOOR UNIT Route of Pipeline 1. Depending on the position of the unit, the piping may be routed sideways from the left or the right (Fig 1), or vertically from the back (Fig 2) (depending on the pipe length of the indoor unit). In the case of sideway routing, cut off the outlet cutting stock of the opposite side. Fig 1. Fig 2. Drainpipe Connection 1. 2. Remove the mountings and pull the indoor unit pipe out of the housing.
INSTALLATION: INDOOR UNIT Wrap the Piping 1. 2. 3. Use the insulation sleeve to wrap the joint part of the indoor unit and the connection pipe. Then use the insulating material to pack and seal insulation pipe, to prevent generation of condensate water on the joint part. Connect the water outlet with drainpipes, and make the connection pipe, cables, and the drain hose straight. Use plastic cable ties to wrap the connecting pipes, cables and drain hose. Run the pipe sloping downward.
INSTALLATION: INDOOR UNIT Wiring Diagram • • If the air conditioner is provided with an interconnection cord, the wiring of the indoor unit is connected in the factory, there is no need of connection. If the interconnection cord is not provided, connection is needed in accordance with the wiring diagram. Constant Speed Variable Speed 5 4 3 2(N) 1(L) 5 4 3 2(N) 1(L) L L N Lo S N S Connector If there is a connector, connect it directly.
INSTALLATION: OUTDOOR UNIT Clearance Drawing for Outside Installation 7.9 in 11.8 in 11.8 in NOTE: All measurements should be no less than posted from obstructions. Unit Mounting Dimensions A B W1 W2 NOTE: Technique to measure distance does not change between unit design versions. Installation Outdoor Unit Bolt Unit BTU 12K BTU 18K BTU 24K BTU Outdoor Unit Size W1(W2)*H*D (in. ") 28.74(30.4)*21.46*11.22 30.90(33.5)*21.90*11.8 32.48(34.3)*25.79*12.2 A (in. ") B (in. ") 21.1 21.1 24.6 10.9 12.7 13.
INSTALLATION: OUTDOOR UNIT Wiring Connection 1. 2. 3. 4. 5. Loosen the screws and remove the E-parts cover from the unit. Connect the cables to the corresponding terminals of the terminal board of the outdoor unit (see the wiring diagram), and if there are signals connected to the plug, just create a butt joint. Ground Wire: Remove the grounding screw out of the electric bracket, cover the grounding wire end onto the grounding screw and screw it into the grounding hole.
INSTALLATION: OUTDOOR UNIT Expelling the Air Outdoor Unit Refrigerant Discharging Method: • After the pipe side connection is complete, proceed as follows. Gas Part Wait for 8 seconds. Loosen the temporarily fastened nut by half a turn. Quickly tighten and connect the nut. The installing torque is the same as that of the gas end of the indoor unit. Liquid Part Check that all indoor and outdoor connections are free of air leakage. Fully open the spindles of the liquid end and of the other two ends.
INSTALLATION: OUTDOOR UNIT Outdoor Condensation Drainage • When the unit is heating, the condensing water and defrosting water can go through the drain elbow. Installation: • There are three drain holes to choose from. Install the outdoor drain elbow in one of the ⌀ 25 mm hole on the base plate and join the drain hose to the elbow. Plug any unused holes. This will provide a proper outlet for any wastewater collecting in the outside unit. Chassis Drain Elbow NOTE: Drain elbow is not included.
NOTICES FOR USE Temperature Range Conditions • Outside the temperature range provided in following table, the air conditioner may shut down. Cooling > 109.4˚F > 125.6˚F < 64.4˚F > 75.2˚F > 19.4˚F > 80.6˚F Outdoor Indoor Heating Outdoor Indoor • • • When the temperature is too high, the air conditioner may activate the automatic protection device and shut the unit down. When the temperature is too low, the heat exchanger may freeze, leading to water leakage or another malfunction.
NOTICES FOR USE Emergency Operation • • • • If the remote controller is lost or broken, use the force switch button to operate the air conditioner. If this button is pushed with the unit OFF, the air conditioner will operate in AUTO mode. If this button is pushed with the unit ON, the air conditioner will stop running. The force switch is located on the right side of the unit and is in a tight space. User may need a thin object such as a screwdriver to push the button.
SAFETY INSTRUCTIONS – UNIT OPERATION Always be careful when using the machine. To reduce the risk of fire, electrical shock, or other injuries, keep these safety considerations in mind when installing, using, and maintaining your machine. . CAUTION 1. 2. 3. 4. 5. 6. 7. Do not let the remote controller drop or fall. Do not let the remote controller get wet. Do not expose the remote controller directly to the sunlight or excessive heat.
REMOTE CONTROL FUNCTIONS NOTE: The remote controller displays all symbols during power-on and only those corresponding to operation the rest of the time. 1. ON / OFF • Press this button to turn on/off the unit. • This will clear the existing timer and sleep settings. SET TEMPERATURE AUTO FAN COOL HIGH DRY MID HEAT LOW ON/OFF 8 9 10 1 SET 2 MODE TURBO SPEED SLEEP ⁰C / ⁰F DISPLAY 3 11 12 13 14 15 SWING ANTI-M SWING ECO CLEAN SENSE TIMER 4 5 6 7 2.
REMOTE CONTROL FUNCTIONS 6. • • • • • TIMER With the unit ON, press this button to set OFF timer, with it OFF, press to set ON timer. Press this button once, an “ON (OFF)” will flash. Press “˄” or “˅” to set the number of hours in which the unit will be turned ON/OFF, with an interval of 0.5 hour if less than 10 hours, or 1 hour if longer than 10 hours, and a range of 0.5-24 hours. Press it again to confirm the setting, the “ON (OFF)” will stop flashing.
REMOTE CONTROL FUNCTIONS 11. SLEEP • Press this button to enter SLEEP mode, which the unit will exit after 10 hours of continuous operation and restore to the previous status. NOTE: The SLEEP function cannot be activated in FAN mode. 12. SWING (Vertically) • Press this button to activate up/down swing and press it again to reset the swing position. 13. SWING (Horizontally) • Press this button to activate left/right swing and press it again to reset the swing position. 14.
AIR CONDITONER OPERATION Install Batteries 1. 2. Install the batteries included with the unit. (Triple A) and position the batteries to the right electric poles (+ and -). Put back on the cover. Automatic Operation Mode 1. Press the “MODE” button, select the automatic operation mode. 2. By pressing the “SPEED” button, you can select the fan speed from LOW, MID, HIGH, AUTO. 3. Press the “ON/OFF” button, the air conditioner starts to operate. 4. Press the “ON/OFF” button again, the air conditioner stops.
AIR CONDITIONER OPERATION Fan Operation Mode 1. Press the “MODE” button, select the fan operation mode. 2. By pressing the “SPEED” button, you can select the fan speed from LOW, MID, HIGH. 3. Press the “ON/OFF” button, the air conditioner starts to operate. 4. Press the “ON/OFF” button again, the air conditioner stops. NOTE: In the fan operation mode, the temperature settings is non-effective. Drying Operation Mode 1. Press the “MODE” button, select the drying operation mode. 2.
MACHINE MAINTENANCE WARNING: • • • Before cleaning the air conditioner, it must be shut down and the electricity must be cut off for more than 5 minutes, otherwise there is a risk of electric shock. Do not wet the air conditioner, which can cause an electric shock. Make sure not to rinse the air conditioner with water under any circumstances. Do not use liquid or corrosive cleaning agents when wiping the air conditioner. Do not sprinkle water or any other liquid on the unit.
MACHINE MAINTENANCE Check Before Use 1. 2. 3. 4. 5. Check whether all the air inlets and outlets of the units are unblocked. Check whether there is blocking in the water outlet of the drainpipe, and immediately clean it up if any. Check the ground wire is reliably grounded. Check whether the remote control batteries are installed, and whether the power is sufficient. Check whether there is damage in the mounting bracket of the outdoor unit, and if any, please contact a qualified service technician.
TROUBLESHOOTING In case of problems, first turn off the air conditioner and disconnect from the source of electricity.
TWO YEARS LIMITED WARRANTY Royal Sovereign International, Inc. warranties this product to be free from defects in material and workmanship for a period of two (2) years. This warranty is extended to the original purchaser only as outlined below: Parts: Replacement of defective parts for 2 years from the date of customer purchase. Compressor: 3-year warranty from the date of customer purchase. Royal Sovereign will supply a replacement compressor (parts only), free of charge. Labor: NO LABOR.
ROYAL SOVEREIGN INTERNATIONAL, INC. 2 Volvo Dr., Rockleigh, NJ 07647 USA TEL: +1 855-687-2223 Email: supportusa@honeywelldispensers.com The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. This product is manufactured by Royal Sovereign International.
