Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Wi-Fi Module Data Sheet This device is pre-calibrated and integrates the complete transmit/receive RF paths including band pass filter, diplexer, switches, reference crystal oscillator, and power manage units (PMU). The HON-ST60Q device supports IEEE 802.11 ac 1X1 receive multi-user MIMO spatial stream multiplexing with data rates up to MCS9 (433.3 Mbps).
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Advanced WLAN ▪ A-MPDU RX (de-aggregation) and TX (aggregation) supports 802.11ac single-MPDU A-MPDU. ▪ Multi-BSS/Station ▪ Transmit rate adaption, transmit power control ▪ Modulation and coding scheme (MCS): 802.11ac—MCS0-9 & 802.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States SPECIFICATIONS Main Chip:Marvell 88W8997 (WLAN); Input Voltage Requirements: DC 3.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Feature Wi-Fi Standards: IEEE 802.11a, 802.11b, 802.11d*, 802.11e, 802.11g, 802.11h, 802.11i, 802.11k*, 802.11n, 802.11r, 802.11s*, 802.11v*, 802.11ac * Summit version only Wi-Fi Data Rates Supported: Support 802.11 ac/a/b/g/n 1X1 MIMO. 802.11b (DSSS, CCK) 1, 2, 5.5, 11 Mbps 802.11a/g (OFDM) 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11n (OFDM, HT20/HT40, MCS 0-7) 802.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States FCC 5.15 GHz to 5.35 GHz (Ch 36/40/44/48/52/56/60/64) 5.47 GHz to 5.725 GHz (Ch 100/104/108/112/116/120/124/128/132/136/140/144) 5.725 GHz to 5.85 GHz (Ch 149/153/157/161/165) 5 GHz Operating Channels (Wi-Fi) ETSI: 19 non-overlapping; FCC: 24 non-overlapping Transmit Power: 802.11a: 15 dBm +/- 1dBm 802.11b: 13 +/- 1dBm 802.11g: 13 +/- 1dBm 802.11n (2.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Compliance Information Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions: 1.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada Statement This device complies with Industry Canada’s license-exempt RSSs.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following condition: ▪ The transmitter module may not be co-located with any other transmitter or antenna.
Honeywell International Inc Honeywell Safety and Productivity Solutions 9680 Old Bailes Rd. Fort Mill, SC 29707 United States l'obtention d'une autorisation distincte au Canada. End Product Labeling The end product must be labeled in a visible area with the following: Contains IC: 1693BHONST60Q. Plaque signalétique du produit final Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: Contient des IC: 1693B-HONST60Q.