Steam Humidifier Homeowner’s Manual HOMEOWNER’S OPERATING MANUAL M35262 TM 69-2286EF-05
Steam Humidifier 2 3 3 11 11 12 12 13 14 19 20 20 SERVICE What should I do if the Service light is blinking?. . . . 21 What if I am having a problem with the Steam Humidifier? . . . . . . . . . . . . . . . . . 21 WARRANTY 5-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . 22 CLEANING AND MAINTENANCE EVERYDAY OPERATION How do I operate the Steam Humidifier?. . . . . . . . . . How do I use the humidity control? . . . . . . . . . .
INTRODUCTION Safety Definitions and Precautions Must be installed by a trained, experienced technician. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. Please read this manual completely. It is important that you understand how the Steam Humidifier works, and how to safely perform the required maintenance procedures. Read and understand all safety-related labels found on and posted near the Steam Humidifier.
Welcome! Congratulations on your new humidifier. We are sure the Steam Humidifier will be a welcome addition to your home. • How is the Steam Humidifier different from other humidifiers? - The steam goes directly into your hot air supply duct, rather than evaporating from a wet pad, which requires furnace temperature to produce humidity efficiently. - The Steam Humidifier delivers humidity independent of your furnace. This allows you to achieve ideal humidity levels in your home, year-round.
How does the Steam Humidifier work? INTRODUCTION 1 5 1. A call for humidity comes from the humidity control provided with the Steam Humidifier. The humidity control is connected to the Steam Humidifier, either with wires or by wireless connection. 2. The heating element coil heats water in the tank to the boiling point. 3. The resulting steam flows out of the Steam Humidifier into the hot air supply duct of your HVAC system.
Which Steam Humidifier model do I have? The Steam Humidifier is available in two sizes, each with a different humidifying capacity: HM609 HM612 Delivers up to 9 gallons of water each day into your home. It is generally suitable for homes 8,000 to 18,400 cubic feet in size. Delivers up to 12 gallons of water each day into your home. This model is generally suitable for homes 12,000 to 24,000 cubic feet in size. YOUR NEW STEAM HUMIDIFIER The proper model for your home depends on many factors.
Which humidity control do I have? YOUR NEW STEAM HUMIDIFIER The Steam Humidifier comes with a humidity control. Your humidity control will either be included in your home thermostat (RedLINK Prestige or VisionPRO IAQ), or it will be a separate device (TrueIAQ or HumidiPRO). You will use the humidity control to set the desired humidity level for your home, and to turn the Steam Humidifier on and off.
How is my Steam Humidifier installed? Your HVAC Professional Installer will install the Steam Humidifier in a proper location in your home. The best location depends on your furnace type and configuration, and how your living space is arranged around the furnace ducts. Your Steam Humidifier will be either duct mounted or remote mounted. ply p Su n Duct mounting. The Steam Humidifier is installed directly onto the supply (hot) air duct of your furnace.
What Steam Humidifier parts do I need to know? Your Steam Humidifier installation includes the following parts and components that you should be familiar with: YOUR NEW STEAM HUMIDIFIER A B C D IMPORTANT: the Steam Humidifier requires cold water. Do not connect a hot water supply to the Steam Humidifier. E F B. Water Supply Line This 1/4-inch line brings cold water to the Steam Humidifier from a water pipe in your home.
G. Safety Release Button This button prevents the tank release lever from accidentally moving forward and releasing the water tank. Press and hold the button down to move the lever forward. H. Ventilation Holes These holes provide airflow for the electronic components inside the Steam Humidifier cover. Normal maintenance includes keeping these holes clean. I. Steam Humidifier Cover The Steam Humidifier wiring connections and electronic components are located behind the cover.
What should I expect from my Steam Humidifier? YOUR NEW STEAM HUMIDIFIER Honeywell wants to make sure you know what to expect from your new Steam Humidifier installation. Make sure you discuss these items with your Professional Installer: 10 • Achieving Humidity Setpoint. It may take up to a week of continuous operation to initially achieve the humidity setpoint. This depends on factors such as weather, size of home, furnishings in the home, and insulation.
How do I operate the Steam Humidifier? Once the Steam Humidifier is installed and running, operation is automatic. Use the humidity control provided to make any changes to the setpoint, or to turn the Steam Humidifier on or off. Your Professional Installer configured the Steam Humidifier so that it only creates steam when conditions in your HVAC system are right. Steam can only be produced when your system fan is blowing air through the duct. Be sure to read the manual that came with your humidity control.
• What should my humidity setpoint be? The outdoor air temperature affects how much humidity can be retained by the air in your home. Use this table as a starting point. Then adjust the humidity control to your own comfort or until condensation appears on the windows.
What do the lights tell me? The six lights show the Steam Humidifier status and indicate when service needs to be performed. Power (Green). On indicates the power cord is plugged in. Humidifying (Green). Lit – Steam Humidifier is actively heating water and creating steam. Blinking – Steam Humidifier is resetting or filling. This is usually done when plugging in the power cord, and lasts for about 3 minutes. You can press the Go button to reset the Steam Humidifier immediately.
When will I press the Drain and Go buttons? The two buttons are used when starting the Steam Humidifier and to manually drain the tank. Drain Button: Press and hold to drain water from the Steam Humidifier tank. See “How do I clean the tank?” on page 16. EVERYDAY OPERATION When the Draining light is blinking, the Steam Humidifier is actively flushing water during a manual drain. Go Button: Press to start or reset the Steam Humidifier when the Humidifying light is blinking.
What is the automatic flush cycle? The Steam Humidifier automatically flushes out the water tank during the humidifying season. In the automatic flush cycle, cold water enters the tank while water is being emptied through the drain line. The action of simultaneous filling and draining cools the water to a safe draining temperature. It also dilutes water hardness concentration to reduce mineral deposits from forming in the tank.
Why do I need to manually clean the tank? Manual cleaning is needed at least once each season to clean out the mineral deposits that remain in the tank after automatic flushing. Manual cleaning is easy – just empty and remove the water tank and clean the interior components. Then re-assemble and start the Steam Humidifier up again. • When should I clean the tank? The Steam Humidifier should be manually cleaned at least once every 5 months. (Hard water may require more frequent cleaning.
First, firmly grip the tank bottom. Then push down the safety release button. 5 Pull the latch forward to release the tank. Note: The latch remains attached to the Steam Humidifier and is not removed with the tank. Remove the tank. 6 7 MCR29672 Remove the sediment screen from the bottom of the tank.
How do I reassemble and start up the Steam Humidifier? Follow these steps to reassemble the tank and start up the Steam Humidifier after cleaning: Attach tank by raising the latch. Pull the white water valve forward to connect to the the black spool. Then turn the manual shutoff valve to the “Lock” position. 1 2 MCR29675 CLEANING AND MAINTENANCE Plug in the power cord. 3 4 MCR29676 The Power light will be on at start-up.
How do I change the water filter? • hanging the reverse osmosis filter cartridges. If the reverse osmosis filter is used in your C installation, you will need to replace two filter cartridges once every humidification season. Notice that the reverse osmosis filter option has more components than the in-line filter and includes a separate drain line. This option provides better filtration and prevents harder water from flowing into your Steam Humidifier. 1 Remove filters #1, #2, and #3, in this order.
What should I do at the end of the season? The Steam Humidifier automatically shuts down when humidity is not needed for an extended period. After several days of inactivity, the water tank will drain and remain empty until humidity is called again. This prevents water from stagnating inside the tank. The Steam Humidifier will refill the tank with water and reset itself when your control calls for humidity again. Follow these maintenance steps at the end of the heating season.
What should I do if the Service light is blinking? The red Service light blinks when the internal diagnostics detect a problem with the Steam Humidifier. Follow these steps to try and correct the problem: 1. Press and hold the Go button to clear the fault. If the Steam Humidifier can reset itself, the Service light will stop blinking, and the Steam Humidifier will operate normally. No further action is required. 2.
5-Year Limited Warranty Honeywell warrants this product to be free from defects in the workmanship or materials, under normal use and service, for a period of five (5) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
WARRANTY Steam Humidification System 69-2286EF—05 23
Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Ltd 705 Montrichard Avenue Saint-Jean-sur-Richelieu, Québec J2X 5K8 http://yourhome.honeywell.com ® U.S. Registered Trademark. © 2014 Honeywell International Inc. 69-2286EF—05 M.S. Rev. 08-14 Printed in U.S.A.
Guide du propriétaire – Humidificateur à vapeur GUIDE DE FONCTIONNEMENT POUR LE PROPRIÉTAIRE M35262 TM
Humidificateur à vapeur à osmose inversée (OI). . . . . . . . . . . . . . . . . . 19 Que dois-je faire à la fin de la période d’humidification?. . . . . . . . . . . . . . . . . . . . . . . . . . 20 Que dois-je faire lorsque je pars en vacances?. . 20 GARANTIE Garantie limitée de 5 ans. . . . . . . . . . . . . . . . . . . . . . 22 BESOIN D’AIDE? Pour de l’assistance au sujet de ce produit, veuillez consulter le site http://yourhome.honeywell.
INTRODUCTION Définitions et précautions relatives à la sécurité L’installation doit être faite par un technicien d’expérience ayant reçu la formation pertinente. Lisez attentivement ces instructions. Le fait de ne pas les suivre risque d’endommager le produit ou de constituer un danger. Veuillez lire ce manuel dans son intégralité. Il est important de comprendre le fonctionnement du système d’humidificateur à vapeur et de savoir exécuter les procédures d’entretien requises en toute sécurité.
Bienvenue! Le système d’humidification à vapeur de Honeywell procure les mêmes avantages de haut rendement et d’efficacité que la vapeur, mais sans nécessiter autant d’entretien que les humidificateurs classiques. INTRODUCTION Nous vous félicitons d’avoir fait l’acquisition de ce nouvel humidificateur. Nous sommes confiants que le système d’humidificateur à vapeur sera un ajout apprécié dans votre domicile.
Comment fonctionne le système d’humidificateur à vapeur? INTRODUCTION 1 5 1. Une demande de production en humidité est acheminée par le régulateur d’humidité fourni avec le système d’humidificateur à vapeur. Le régulateur d’humidité est branché au système d’humidificateur à vapeur, au moyen d’une connexion filaire ou sans fil. 2. La bobine de l’élément chauffant chauffe l’eau dans le réservoir jusqu’à ce qu’elle atteigne le point d’ébullition. 4 3 3.
Quel modèle de système d’humidificateur à vapeur ai-je en ma possession? L’humidificateur à vapeur est offert en deux formats, chacun procurant une capacité d’humidification différente : HM609 HM612 Le modèle HM509 fournit jusqu’à 9 gallons par jour dans votre domicile. Il convient généralement à des domiciles dont le volume varie entre 8 000 et 18 400 pi3. Le modèle HM512 fournit jusqu’à 12 gallons d’eau chaque jour dans votre domicile.
Quel régulateur d’humidité ai-je? VOTRE NOUVEAU SYSTÈME D’HUMIDIFICATEUR À VAPEUR Le système d’humidificateur à vapeur est équipé d’un régulateur d’humidité. L’appareil peut être de type inclus dans votre thermostat domestique (RedLINK Prestige ou VisionPRO IAQ) ou il peut s’agir d’un appareil autonome (TrueIAQ ou HumidiPRO). Vous utiliserez le régulateur d’humidité pour régler le taux hygrométrique de votre domicile et pour mettre le système d’humidificateur à vapeur en fonction et hors fonction.
Comment mon système d’humidificateur à vapeur est-il installé? Votre installateur professionnel CVCA installera le système d’humidificateur à vapeur dans un emplacement adéquat de votre domicile. Le meilleur emplacement dépend du type et de la configuration de votre fournaise, et de la disposition de votre surface habitable autour des gaines de fournaise. Votre système d’humidificateur à vapeur sera soit monté en gaine ou à distance. tio ta en n m Ali Montage en gaine.
Quelles sont les pièces du système d’humidificateur à vapeur qu’il importe de connaître? L’installation du système d’humidificateur à vapeur inclut les pièces et les composants suivants que vous devriez connaître : VOTRE NOUVEAU SYSTÈME D’HUMIDIFICATEUR À VAPEUR A B C D E A. Un raccord d’eau froide doté d’une vanne d’arrêt Permet de raccorder le système d’humidificateur à vapeur à la canalisation d’alimentation en eau froide de votre domicile.
E. Cordon d’alimentation Le système d’humidificateur à vapeur est branché dans une prise de courant domestique de 120 volts c.a. Le cordon d’alimentation fourni mesure 1,8 m (6 pieds). G. Bouton de dégagement de sûreté Ce bouton empêche le levier de déclenchement du réservoir de se déplacer inopinément vers l’avant et de libérer le réservoir d’eau. Appuyez sur le bouton et maintenez-le enfoncé pour déplacer le levier vers l’avant. H.
Que dois-je attendre du système d’humidificateur à vapeur? VOTRE NOUVEAU SYSTÈME D’HUMIDIFICATEUR À VAPEUR Honeywell veut s’assurer que vous savez à quoi vous attendre de votre humidificateur à vapeur. Assurez-vous d’aborder les points suivants avec votre installateur professionnel : 10 • Établissement du point de consigne d’humidité. Il peut s’écouler jusqu’à une semaine de fonctionnement continu avant que le point de consigne d’humidité ne soit établi.
Comment fonctionne le système d’humidificateur à vapeur? Une fois le système d’humidificateur à vapeur installé et fonctionnel, le fonctionnement est automatique. Utilisez le régulateur d’humidité fourni pour modifier le point de consigne, ou pour mettre le système d’humidificateur à vapeur en fonction et hors fonction.
• Comment établir le point de consigne d’humidité? La température de l’air extérieur a une incidence sur la quantité d’humidité présente dans l’air de votre domicile. Utilisez ce tableau comme point de départ. Réglez ensuite le régulateur d’humidité selon vos préférences ou jusqu’à ce que de la condensation se forme dans les fenêtres.
Que m’indiquent les voyants? Les six voyants indiquent l’état du système d’humidificateur à vapeur de même que la nécessité de procéder à des réparations. Alimentation (vert) allumé indique que le cordon d’alimentation est branché. FONCTIONNEMENT QUOTIDIEN En cours d’humidification (vert) Allumé – Le système d’humidificateur à vapeur est en train de chauffer l’eau et de produire de la vapeur. Clignotement – Le système d’humidificateur à vapeur est en cours de réinitialisation ou de remplissage.
Quand dois-je enfoncer les boutons Drain (Vidange) et Go (Aller)? Les deux boutons sont utilisés pour mettre le système d’humidificateur à vapeur en route et pour vidanger manuellement le réservoir. Bouton Drain (Vidange) : Appuyez sur le bouton Drain (Vidange) pour vider l’eau du réservoir du système d’humidificateur à vapeur. Consultez la rubrique « Comment dois-je procéder pour nettoyer le réservoir? » de la page 16.
En quoi consiste le cycle de vidange automatique? Le système d’humidificateur à vapeur vidange automatiquement le réservoir pendant toute la saison d’humidification. Lors du cycle de vidange automatique, l’eau froide pénètre dans le réservoir pendant que l’eau est expulsée dans la canalisation de vidange. L’action du remplissage et de la vidange simultanés refroidit l’eau jusqu’à ce sa température atteigne un niveau sécuritaire.
Pourquoi dois-je nettoyer manuellement le réservoir? Un nettoyage manuel est requis au moins une fois par saison pour débarrasser le réservoir des dépôts minéraux qui subsistent après la vidange automatique. Il est facile de nettoyer le réservoir. Il suffit de le vider, de le démonter et de nettoyer les composants intérieurs. Après la remise en place du réservoir, le système d’humidificateur à vapeur est prêt à fonctionner de nouveau.
Commencez par saisir fermement le fond du réservoir. Appuyez ensuite sur le bouton de dégagement de sûreté. 5 Tirez le verrou vers l’avant pour libérer le réservoir. Remarque : Le verrou reste fixé au système d’humidificateur à vapeur et n’est pas déposé en même temps que le réservoir. Déposez le réservoir. 6 7 MCR29672 Déposez la crépine à sédiments du bas du réservoir.
Comment dois-je procéder pour remonter et démarrer le système d’humidificateur à vapeur? Suivez ces étapes pour remonter le réservoir et démarrer le système d’humidificateur à vapeur après le nettoyage : Fixez le réservoir en soulevant le verrou. Tirez le bras de la vanne d’eau blanche vers l’avant pour l’accoupler à la bobine noire. Tournez ensuite la vanne d’arrêt manuelle à la position « Lock » (Verrouiller). 1 2 MCR29675 NETTOYAGE ET ENTRETIEN Branchez le cordon d’alimentation.
Comment dois-je procéder pour remplacer le filtre à eau? • emplacement des cartouches de filtre à osmose inversée Si votre installation est dotée d’un filtre à R osmose inversé, vous devrez remplacer deux cartouches de filtre à chaque saison d’humidification. Notez que le filtre à osmose inversé dispose de plus de composants que le filtre en ligne et qu’il inclut une canalisation de vidange distincte.
Que dois-je faire à la fin de la saison? Le système d’humidificateur à vapeur cesse automatiquement de fonctionner lorsqu’il n’est pas nécessaire de produire de l’humidité pendant une période prolongée. Après plusieurs jours d’inactivité, le réservoir d’eau se videra et restera vide jusqu’à la prochaine demande de production d’humidité. Cela empêche la stagnation d’eau dans le réservoir.
Que dois-je faire si le voyant Service (Réparation) clignote? Le voyant rouge Service (Réparation) clignote lorsque le dispositif interne détecte une anomalie dans le système d’humidificateur à vapeur. Suivez ces étapes pour essayer de corriger le problème : 1. Appuyez sur le bouton Go (Allez) et maintenez-le enfoncé pour effacer l’anomalie.
Garantie limitée de 5 ans Honeywell garantit ce produit contre tout vice de fabrication ou de matière dans la mesure où il en est fait une utilisation et un entretien convenables, et ce, pour cinq (5) ans à partir de la date d’achat par le consommateur. En cas de défectuosité ou de mauvais fonctionnement pendant la période de garantie, Honeywell remplacera ou réparera le produit (au gré de Honeywell).
GARANTIE Système d’humidification à vapeur 69-2286EF—05 23
Solutions de régulation et d’automatisation Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Ltd 705 Montrichard Avenue Saint-Jean-sur-Richelieu, Québec J2X 5K8 http://yourhome.honeywell.com ® Marque de commence enregistrée aux États-Unis © 2014 Honeywell International Inc. 69-2286EF—05 M.S. Rev.