OPERATION MANUAL Day and Night / WDR OSD COLOR CAMERA HCC-745NTW/PTW READ AND KEEP THIS OPERATION MANUAL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature - 1 accompanying the appliance.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. PREFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Indicate a potentially hazardous situation which if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Warning: This equipment generates and uses radio frequency energy and if not installed and used properly, I.e.
CAUTION FOR SAFE OPERATION 1. Water and Moisture To prevent fire or shock hazard, do not expose this camera to rain or moisture. 2. Servicing Do not attempt to disassemble or repair by yourself. You may be exposed to dangerous voltage or other hazards. Note that all servicing is qualified service personnel. Modifications not approved by manufacturer could void the user's authority to operate the equipment. 3.
CONTENTS 1. Features ----------------------- 5 2. Names & Functions ----------------------- 6 3. Installation ----------------------- 8 4. Remote Control Connections ----------------------- 10 5. On Screen Display ----------------------- 11 6. Specifications ----------------------- 19 7. Dimensions ----------------------- 20 Thank you for using this OSD Color Camera with Day and Night, WDR.
1. Features Honeywell’s HCC-745NTW/PTW Series is a high sensitivity CCD color camera with high sensitivity function of Day & Night function and field integration technique. ▣ 1/3” Double Scan Color CCD ( NTSC: 410,000 / PAL: 470,000 ) ▣ Outstanding BLC implementation with WDR(Wide Dynamic Range) function. ( 3 steps available : OFF / BLC / WDR ) ▣ Adapted CS/C mount lens adjustable. ▣ Excellent signal-to-noise ratio of more than 50dB. ▣ High Sensitivity : Minimum illumination of 0.001lx @ F1.
2.
(+) BUTTON VIDEO OUTPUT This is the output terminal for composite video signal (UP) BUTTON (-) BUTTON POWER ON LAMP In power ON state, this LED is ON . MENU BUTTON (DOWN) BUTTON POWER INPUT TERMINAL Lens Type Select Switch DC Lens : with no iris amp. VSD Lens : with iris amp. CAMERA CONTROL CONNECTOR ( Refer to 4.
3. Installation 3.1 The packing box should include, in addition to this User Guide: -. One HCC-745NTW or HCC-745PTW camera -. One 6-pin connection cable ( G-113510-200 ) -. One Auto Iris lens plug 3.2 Mounting a Lens 3.2.1 C/CS Mount Lens ① Remove the protective cap in front of the camera. ② Adjust the mount ring whether it is for C or CS. ③ Loosen Set Screw. ④ Turn the mount ring counterclockwise in case of C-Mount Lens. Turn the mount ring clockwise in case of CS-Mount Lens 3.2.
④ Set the switch on the rear of the camera to DC or VSD. ☞ Use the connection recommended by the manufacturer. (E4-191, Chuo Musen, Japan) For best practices, read the lens manual carefully. You may need to set the flange back focus. 3.3 Flange back focus adjustment 3.3.1 Fixed Lens a. Loosen the setscrew and set the lens focus ring to infinity ( ∞ ) . b. Turn the back focus adjustment ring until you see a clear image (the distance from the camera to the object is more than 23m). c. Tighten the setscrew. 3.
4. Remote Control Connections 4.1 RS-232C connection ( HCC-745NTW/PTW ) Connect to Serial PORT Serial Cable RS232C Serial Cable ( 9 Pin D-Sub ) 1. 2. 3. 4. 5. 6. Red : Not Use Blue : RD(TxD) Yellow : TD(RxD) Black : GND Red : Not Use Black : Not Use 1. 2. 3. 4. 5. 6. Red : Not Use Blue : TRxYellow : TRx+ Black : Not Use Red : Not Use Black : Not Use 6P Cable 6P Cable RD 2 2 RD ( TxD ) TD 3 3 TD ( RxD ) SG 5 4 GND 4 6 7 Connect internally for communication 8 4.
FUNCTION 5. On Screen Display ② ②, ③ ZOOM DISPLAY ① CAMERA ID ②, ③ ⑤ ① ④ ⑥ DESCRIPTION Dx2.5 >>TELE Zoom TELE Dx1.0 << WIDE Zoom WIDE None display ID : 0 ID : 002 ID : 1 ~ 255 ③ TITLE ■■…■■ See 5.
<< SETUP MENU >> GENERAL SETTING AE MODE WB MODE NIGHTSHOT MODE BLC/WDR MODE PZM SETTING CAMERA ID SETTING SPECIAL FUNCTION FACTORY DEFAULT EXIT MENU <> 0 SYNC. LEVEL 98 BURST LEVEL AUTO SYNC. MODE L/L RETURN 5.2 Display SETUPMENU a. Press and hold the MENU (center) button for 2 seconds to display the Setup menu. b. Press the UP or DOWN buttons to select a menu item. 5.3 Move from SETUPMENU to submenu a. Press the MENU button to enter the selected submenu. b.
⑤ LENS ADJUSTMENT : Adjust level for DC / VSD lens. While it is adjusting, it displays “Adj-ing”, after it is completed, it displays “Done”. LENS ADJ. Adj-ing → Done << AE MODE >> ELC ① MODE AUTO ② CONTROL 1/60 ③ MAN. SHUTTER OFF ④ MAN. AGC Done ⑤ LENS ADJ. 60 ⑥ BRIGHTNESS 34dB ⑦ MAX GAIN 510FLDS ⑧ MAX FIELDS RETURN ☞ Notice For the better adjustment, set LEVEL on VSD lens to middle value. ⑥ BRIGHTNESS : Adjust level of Auto Iris.
② CONTROL ATW IN OUT MANUAL AWC AWC FLUORES. USER << WB MODE >> USER ① MODE R/B CONT ② CONTROL 1 ③ RED GAIN 2 ④ BLUE GAIN RETURN AUTO 3200°K 5400°K R<-->B LOCK → PUSH AUTO 4200°K R/B CONT 1. MANUAL : Press + or – button to adjust RED GAIN, BLUE GAIN automatically to fit Black Body. 2. PUSH : Press + or – button to start the AWC operation. LoCK : Release the key to fit the present shooting scene’s white balance ③ RED GAIN (USER mode) RED GAIN 0 → 1 → …. → 254 → 255 5.
⑤ NIGHT COLOR : Set the color mode as B/W (monochrome) or COLOR in Night mode. NIGHT COLOR B/W → COLOR → …. << NIGHTSHOT MODE >> AUTO ① MODE 3sec. ② DETECT TIME 3 ③ D→N LEVEL 7 ④ N→D LEVEL B/W ⑤ NIGHT COLOR RETURN ☞ Notice MODE must be set to AUTO or ON. << BLC/WDR MODE >> WDR ① MODE 8 ② LEVEL RETURN 5.
③ Horizontal Start position H START 200 << PRIVACY ZONE >> ZONE 1 ① ZONE NUM. ON ② CONTROL 200 ③ H START 300 ④ H END 50 ⑤ V START 100 ⑥ V END BLACK ⑦ PZM MASKING RETURN ④ Horizontal End position H END 300 ⑤ Vertical Start position V START 50 ⑥ Vertical End position V END 100 ⑦ MASKING COLOR : Choose the color to mask the PZM zone. 10 color (Black,Gray, Light Gray,White,Red,Blue,Green,Yellow, Cyan, Magenta). PRESS MENU TO MOVE PZM MASKING 5.
④ Title : It is the name of Camera. It enters 10 characters including blank.. TITLE: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ << CAMERA ID SETTING >> ① CAMERA ID 000 TITLE ② DISPLAY ③ POSITION R.BOT ⓐ ⓑ ⓒ ⓓ ④ ▣ How to Enter the Title ▣ Let’s enter the Title as “R1” , example -. Select the position of title character by using (+) or (-) key. The chosen position is blinking. ABCDEFGHIJKLMNOPQRST UVWXYZabcdefghijklmn opqrstuvwxyz12345678 9!?#$%&<>*,.:;/+-=~■ TITLE: □ ■ ■ ■ ■ ■ ■ ■ ■ ■ -.
<< SPECIAL FUNCTION >> OFF ① MIRROR 10 ② SHARPNESS OFF ③ NEGATIVE OFF ④ FREEZE 9600bps ⑤ BAUDRATE DEFAULT ⑥ PROTOCOL ALL ⑦ F.OSD DISP RETURN ⑥ PROTOCOL : Use to communicate through RS232C, RS485. PROTOCOL DEFAULT → VCL → KD6 → P/D → .... ⑦ Function OSD Display OSD DISP ALL → NONE → TOP → BOTTOM → ....
6. Specifications Model Name HCC-745NTW HCC-745PTW Pick-up Device Total/Effective Pixels 1/3” Sony Double Scan Color CCD 410,000 / 380,000 Scanning System 525 lines, 2:1 Interlace Digital Zoom Ratio Sync System H.Resolution X1.0 ~ x2.5 can be adjustable Internal / External (L/L ), Auto detecting selectable 480 TV lines S/N Ratio Min. illuminance 470,000/440,000 470 TV lines more than 50 dB ( AGC OFF ) 0.2lx @50IRE, AGC 38dB, Night OFF; 0.01lx @50IRE, AGC 38dB, Night OFF, DSS 510fields; 0.
7.
MEMO Honeywell Co., Ltd. Address : 17F, Kukje Center Building 191, Hankangro -2ga, Yongsan-gu, Seoul 140-702, Korea Phone : 82-2-799-6109, 6108, 6107, 6292 Fax : 82-2-749-6119 Printed in Korea http : //www.honeywell.co.kr/security/english E-mail : info.security@honeywell.