Installation Instructions

ManualsBrandsHoneywell ManualsAir ConditioningHC60NG

Wireless Domestic Heating Zoning System

INSTALLATION GUIDE

YZ667A1060

TABLE OF CONTENTS

Section Page

1 General .................................................. 1

2 Technical Information ..........................

3 Factory Conﬁguration ..........................

4 HC60NG Relay Module .........................

5 CM67z Room Unit .................................

6 HR80UK Radiator Controller ...............

7 System Testing .....................................

7.1 Service mode ......................................................6

8 Changing the Conﬁguration ................ 7

8.1 Parameters of the CM67z ...................................7

8.2 Changing or adding a HR80UK to a zone ........

8.3 Built -in sensor conﬁguration ...........................

8.4 Adding a HC60NG Zone valve controller .........

8.5 Resetting a Bound HR80UK ..............................

9 Trouble Shooting ................................ 10

9.1 Trouble Shooting Guide ...................................10

9.2 Manual adaption ...............................................

9.3

Def (default setting) and Full operating modes

...11

9.4 Resetting the HR 80 to the factory settings ...

1 GENERAL

The CM Zone Wireless Domestic Heating Zoning System

offers high levels of comfort and energy savings for the

home. It provides the ability to control two individual zones

at different comfort levels and at different times. A typical

example being the living areas and the bedrooms being

controlled separately.

The standard CM Zone Pack contains a Room Unit, a Relay

Module and six Radiator Controllers all pre-bound with three

Radiator Controllers bound to Zone 1 and three bound to

Zone 2. The System can be expanded or modiﬁed and the

methods used are described within this Guide.

To get the best from the installed system it is recommended

to use Honeywell VT15, VT117 or VT200 TRV bodies and a

Honeywell DU145 Automatic Bypass Valve.

For application support please contact your nearest

Honeywell salesman, for technical assistance please contact

the Honeywell Technical Help Desk, details are on the back

page.

HC60NG Relay Module CM67z Room Unit

HR80UK Radiator Controllers

42010824-003 R3

2 TECHNICAL INFORMATION

Type numbers

CM67z - Room Unit (x1)

HR80UK - Radiator Controller (x6)

HC60NG - Relay module (x1)

Material

Housings made of plastics (ABS).

Dimensions

CM67z - 155 x 105 x 30 mm. (l x h x d)

HR80UK - 50 x 80 x 105 mm. (l x h x d)

HC60NG - 131 x 97 x 36 mm. (l x h x d)

Power

CM67z - 2 x 1.5 V IEC LR6 (AA) Alkaline cells

HR80UK - 2 x 1.5 V IEC LR6 (AA) Alkaline cells

HC60NG - 230V~ 50Hz powered

Electrical wiring (only for HC60NG)

Mains power supply

Relay output rating: 24-230 V~, 10A resistive,

3A inductive 0.6 p.f.

Programming Capability

2 individual heating programs

7 days with 6 temperature change times per day

Approvals

DIN EN ISO 9001/14001, CE, EN60730-1 (2000),

EN60730-2-9 (2002), EN55014-1 (2000), EN55014-2 (1997),

ETSI EN300 220-3 (2000), ETSI EN301 489-3 (2000)

Summary of content (12 pages)

PAGE 1
YZ667A1060 Wireless Domestic Heating Zoning System INSTALLATION GUIDE 1 GENERAL HC60NG Relay Module The CM Zone Wireless Domestic Heating Zoning System offers high levels of comfort and energy savings for the home. It provides the ability to control two individual zones at different comfort levels and at different times. A typical example being the living areas and the bedrooms being controlled separately.
PAGE 2
Section 3: Factory Configuration Zoning Example The Hydronic Zoning kit is factory pre-configured and has the following components: Zone 1: Living Room + Kitchen (downstairs) Zone 2: Bedrooms (upstairs) • Zone 1 - Three HR80UK Radiator controllers labelled 1 • Zone 2 - Two HR80UK Radiator controllers labelled 2 • HC60NG - Relay box • CM67z - Room Unit Zone 2 To change this factory configuration or to add components please see Section 8: Changing the Configuration.
PAGE 3
Section 4: HC60NG Relay Module The HC60NG Relay Module is an integral part of the CM Zone Control System. It is designed to control a Domestic Boiler, Valve, pump or Electric Heating appliances. In the standard CM Zone Pack the HC60NG Relay Module is configured to control a Boiler based upon demand signals received from the HR80UK Radiator Controllers either directly or via a ‘Y Plan’ / ‘S Plan’ connection described below. For control of other applications see Section 8: Changing the Configuration.
PAGE 4
Section 5: CM67z Room Unit MON TUE WED THU FRI SAT SUN The CM67z Room Unit provides a central point from which to configure the system and set the time and temperature profiles for each Zone. At a given time, as defined within a Zone profile, the CM67z Room Unit transmits the required temperature setpoint to the respective HR80UK Radiator Controllers, local temperature control and override is then provided at each HR80UK Radiator Controller.
PAGE 5
Section 6: HR80UK Radiator Controller The HR80UK Radiator Controller provides local room temperature control based upon setpoint information received from the CM67z Room Unit and sends Load Demand signals based upon room conditions to the HC60NG Relay Module. Setpoints can be temporarily overridden using the adjustment dial. The HR80UK can be fitted onto Honeywell VT15, VT117, VT200 and many other manufacturers TRV bodies with a M30x1.5mm thread and a 12.9 - 10.
PAGE 6
Section 7: System Testing ! Caution! When selecting the operating site ensure that the distance to wireless devices such as wireless headphones, cordless phones etc. is approx. 1-2m. Wall It is recommended to complete the system testing before mounting the wall bracket on the wall. Position the CM67z Room Unit as close as possible to the location where it will be used. Wall Wall = Signal Strength Ceiling Max.
PAGE 7
Section 8: Changing the Configuration 8.1 Parameters of the CM67z Room Unit Installers Set Up Mode allows changing the controllers parameters to meet specific application requirements or customers needs. See fig 1 to 7 how to enter the Installer set-up. 1 2 Move the CM67z slider into the OFF position. DAY 1...7 MON TUE WED THU z1 FRI SAT SUN z2 z1 AM PM COPY DAY AUTO MAN OFF PROG 1 2 MAN z1 4 5 z2 TEMP AUTO MAN OFF 3 Installer Set-Up Number (Press + or - to change) e.g.
PAGE 8
Section 8: Changing the Configuration (cont.) 8.2 Adding further HR80UK Radiator Controllers 1 2 3 b c a b a a Turn the locking knob a and separate the operating unit and coupling module. 4 Turn the coupling module wheel a anticlockwise (approx. 3 rotations) until the nose b reaches the end stop c . 5 Fit the coupling module a to the TRV body b and tighten by hand. For Adaptors see Section 6. 6 Binding Button 1 Install batteries into the operating unit. Note: Check correct polarity.
PAGE 9
Section 8: Changing the Configuration (cont.) 8.2a Binding HR80UK Radiator Controllers to the HC60NG Boiler Module 13 14 15 DAY 1...7 MON TUE WED THU FRI z1 DAY 1...7 SUN z2 z1 AM PM COPY DAY AUTO MAN OFF PROG 1 2 MAN z1 5 secs.
PAGE 10
Section 9: Trouble Shooting 9.1 Trouble Shooting Guide Symptom (Fault Message) Possible Cause Remedy After binding procedure the symbol on HR80UK display is off. Incorrect or incomplete binding procedure. Repeat the binding procedure following the installation instructions. Bad position of the CM67z during binding. Repeat the binding procedure keeping approx. 1 m distance between CM67z and HR80UK. After binding procedure the red LED of the HC60NG is on and the green one is flashing once every 3 sec.
PAGE 11
Section 9: Trouble Shooting (cont.) 9.1 Trouble Shooting Guide (cont.) Symptom (Fault Message) Possible Cause Remedy • The HC60NG LEDs are OFF No power to HC60NG. Check the power to the HC60NG is on. • The HC60NG green LED is ON Bad electrical connection to the boiler or faulty boiler. Check the boiler and HC60NG power supply as well as electrical connection between the boiler and HC60NG. HC60NG red LED is constantly ON or flashing. RF communication lost due to bad location of the CM67z room unit.
PAGE 12
Environmental Note: This product has been designed with your environment in mind! Please respect this by disposing of all packaging and used parts in an environmentally friendly manner. Do not dispose of batteries with household waste. They must be returned in accordance with the local statutory requirements.