Dolphin® Net Base Four-Slot Charging/Communication Cradle for the Dolphin® 7900 Mobile Computer ™ Dolphin® 9500 Mobile Computer Dolphin® 9900 Mobile Computer Quick Start Guide !
Dolphin Net Base Quick Start Guide Introduction The Net Base charges up to four mobile computers and enables each one to communicate with a host device over an Ethernet network. ! Use only the peripherals, power cables, and power adapters from Honeywell. Use of peripherals, cables, or power adapters not sold/manufactured by Honeywell may cause damage not covered by the warranty.
Hardware Overview Front Panel Terminal Wells Dock LED Dock LED COMM LED COMM LED Lights solid green when the terminal is properly seated. The terminal can communicate with the Net Base only when properly seated in the well. Indicates the status of data transfer between the Dolphin terminal and the Net Base. Solid Green: Flashing Orange: Indicates a USB connection. Indicates that data is being transferred.
Power Supply Power Adapter Power Connector Cable ON/OFF Switch Power Cord Setting up the Net Base 1. Make sure the ON/OFF switch on the power adapter is in the OFF position. 2. Plug the power cord into the power adapter. 3. Plug the power connector cable into the power connector on the back of the Net Base. 4. Plug the power cord into a standard wall outlet. 5. Plug the CAT-5 Ethernet cable into either of the RJ-45 connectors on the back of the Net Base. 6.
Charging ! Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty. The Net Base charges the main battery of each terminal in less than four hours. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be stored in the Net Base indefinitely without damage to the terminals, battery packs, or the Net Base. 1.
Configuring the Network By default, the Net Base is configured to obtain IP addresses automatically via DHCP server. This means that in most cases you would simply “plug and play” the unit. If necessary, you can use the configuration utility for dynamic network configuration. If Your DNS Server Supports Bind 8.3 or Later 1. Obtain the serial number from the label on the bottom panel of the Net Base. 2. Connect to the network. 3. Power up and wait until the COMM LEDs stop flashing.
4. Enter the user name and default login password to log into Net Base configuration utility. The Net Base menu program displays. *********************************************** * Welcome to the Honeywell Net Base * *********************************************** SD00032Login: handheld Password: ******** 1) 2) 3) 4) 5) 6) 7) x) View System Configuration View Current Values Express Setup Advanced Setup System Statistics System Diagnostics Help Exit Enter choice: 2 5.
4. Enter the user name and default login password to log into network. *********************************************** * Welcome to the Honeywell Net Base * *********************************************** SD00032Login: handheld Password: ******** 1) 2) 3) 4) 5) 6) 7) x) View System Configuration View Current Values Express Setup Advanced Setup System Statistics System Diagnostics Help Exit Enter choice: 3 5.
5. The home screen appears. Link Bar Link Click this link to … User’s Guide Open the online help files. Setup Choose IP address assignments from two options: • • • Obtain all IP addresses dynamically - Requests five IP addresses from a DHCP server: one is used for the Ethernet interface and the remaining four are assigned to each terminal slot. Specify IP addresses manually - Enables you to specify IP addresses per terminal slot and change the local USB port (PPP) IP address.
Mounting Options The bottom panel offers two mounting options: 1. a DIN Rail for desk mounting or 2. a wall mount kit for wall mounting. Both the DIN Rail and wall mount kits need to be purchased separately. Using the DIN Rail Use a standard 7.5mm high X 35mm wide DIN Rail to mount the Net Base to a horizontal surface, such as a desk or table. Installation Hardware Screw: Washer: Nut: 3/16 in. dia x 5/8 in. long pan head screw 1/2 in. OD x 7/32 in. ID x 3/64 in. thick 3/16 in. dia 1.
Using the Wall Mount Kit You need to purchase two wall mount kits that each contain: • a mounting bracket, • three screws, and • six washer/nut sets. You need two kits so that you have two mounting brackets–one for each end of the device–and enough screws (4) and washer/nut sets (8). The mounting bracket contains an open slot between the back and bottom wedges to accommodate the connector cables. To Mount a ChargeBase Device 1.
Wall Recommended Anchors Concrete Buildex TAPCON concrete anchors 3/16 in. X at least 1 in.
Technical Assistance If you need assistance installing or troubleshooting, please call your Distributor or the nearest technical support office: North America/Canada Telephone: Fax number: E-mail: (800) 782-4263 (315) 554-6705 natechsupport@handheld.com Latin America Telephone: Telephone: E-mail: (803) 835-8000 (800) 782-4263 latechsupport@handheld.com Brazil Telephone: Fax: E-mail: +55 (21) 3535-9100 +55 (21) 3535-9105 brsuporte@handheld.
Product Service and Repair Honeywell provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product. North America Telephone: Fax: E-mail: (800) 782-4263 (803) 835-8012 naservice@handheld.com Latin America Telephone: Telephone: Fax: E-mail: (803) 835-8000 (800) 782-4263 (239) 263-9689 laservice@handheld.
Limited Warranty Honeywell International Inc. ("Honeywell") warrants its products to be free from defects in materials and workmanship and to conform to Honeywell’s published specifications applicable to the products purchased at the time of shipment.
Honeywell extends these warranties only to users of the products. These warranties are non-transferable. The limited duration of the warranty for the Dolphin Net Base is one year. How to Extend Your Warranty Honeywell offers a variety of service plans on our hardware products. These agreements offer continued coverage for your equipment after the initial warranty expires.
16
Disclaimer Honeywell International Inc. (“Honeywell”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Honeywell.
Honeywell 700 Visions Drive P.O.
