Submittal Sheet

ManualsBrandsHoneywell ManualsCurrent Sensors0-5 VDC Solid Core, "Go/No Go" Current Switch, 50A

Table Of Contents

SPECIFICATION DATA

31-00143-01

CURRENT SENSORS

4-20 MA OUTPUT AND VOLTAGE OUTPUT

CTS-A, CTP-A, CTS-V, CTP-V SERIES SENSORS

OVERVIEW

The 4-20 mA Output Analog Current Sensors and Voltage

Output Analog Current Sensors are designed for use in

any AC current monitoring application in which you are

looking to monitor a particular piece of equipment for

proper operation. All voltage output current sensors use

an “Average” current measuring method and should be

used in applications with a pure Sinusoidal AC waveform

that has very little or no distortion/noise on the conductor

being monitored.

The current sensors are available in both solid and split-

core versions which also includes a 35 mm Din Rail

mounting foot for easy installation in panel mount

applications.

The solid-core versions are a great choice for new

installations or OEM applications in which cost sensitivity,

lower trip points and environmental issues like dust and

moisture may be of concern. The split-core version of the

current sensors work great in retrofit applications and for

use on service technicians vehicles since one or two parts

will work in most applications and can be easily installed

without disconnecting any wires. Voltage Output current

sensors are available in both solid and split-core versions

which also includes a 35 mm Din Rail mounting foot for

easy installation in panel mount applications.

For best results, the voltage output current sensors should

not be used in applications with switching power supplies

or variable speed drives due to the limited operating

frequency range. Applications may include monitoring a

resistive type load such as an incandescent light bulb,

heating element as well as any single speed linear load.

In applications where variable speed drives or waveforms

include distortion/noise, Honeywell recommends the use

of the CTP-A-50-RMS Series sensors where you need to

supply 24 VDC power to the current sensors with a 4-20

mA signal. A 249 Ohm or 499 Ohm 1 Watt resistor can be

used to convert the 4-20 mA signal into a usable 1-5 or 2-

10 VDC output signal at your building management

system or PLC. Note that the “True RMS” sensors are able

to be used in all applications since the “True RMS” current

sensors provide the best overall accuracy and should be

used in applications which include Variable Frequency

Drives, Switching Power Supplies, Computers and Data

Centers, Electronic Ballasts, SCR’s, and Variable Speed

Loads.

Applications

• Load Trending

• Basic Power Monitoring

• Electronic Ballasts

• Computers/Data Centers

• Industrial

• Variable Speed Loads

•Pumps

•Compressors

•Fans

• Preventative Maintenance

• LEED

• Project Justification (ROI) Process Control

• Solid State Environments (SCR’s)

• Single Speed Loads

The Current Sensors are covered by a Five (5) Year Limited

Warranty.

4-20 MA OUTPUT0-5/10 VDC OUTPUT

Summary of content (4 pages)

PAGE 1
CURRENT SENSORS 4-20 MA OUTPUT AND VOLTAGE OUTPUT CTS-A, CTP-A, CTS-V, CTP-V SERIES SENSORS SPECIFICATION DATA sensors are available in both solid and split-core versions which also includes a 35 mm Din Rail mounting foot for easy installation in panel mount applications. For best results, the voltage output current sensors should not be used in applications with switching power supplies or variable speed drives due to the limited operating frequency range.
PAGE 2
CURRENT SENSORS SPECIFICATIONS Response Time (4-20 mA Output): CTS-A and CTP-A: < 600 mS (Rise and Fall Time) CTP-A-50-RMS: 600 mS (Rise Time) and 2800 mS (Fall Time) Voltage Output: < 300 mS (Rise and Fall Times) Monitored Current Type: AC Current Maximum AC Voltage: 600 VAC Isolation Voltage: 2200 VAC Operating Frequency Range (4-20 mA Output): CTP-A-200 & CTS-A-250: 40 to 1 KHz CTP-A-50-RMS: 15 to 100 Hz Voltage Output: 50 to 600 Hz Aperture Size: 0.75 in. (19.
PAGE 3
CURRENT SENSORS Dimensions RIGHT VIEW FRONT VIEW RIGHT VIEW FRONT VIEW 2-35/64 (65) 2-23/64 (60) 2-23/32 (70) 2-49/64 (70) BOTTOM VIEW 1-3/32 (28) 2-7/8 (73) 3-15/64 (82) BOTTOM VIEW 2-7/8 (73) 1-1/32 (26) 3-11/32 (85) M37357 M37358 Fig. 1. Solid-core sensor dimensions in in. (mm). Fig. 2. Split-core sensor dimensions in in. (mm). Table 1. Standard Ordering.
PAGE 4
CURRENT SENSORS By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’ fees, arising out of, or resulting from, any modification to the literature by you. Home and Building Technologies In the U.S.: Honeywell 715 Peachtree Street NE Atlanta, GA 30308 customer.