Install Instructions

ManualsBrandsHoneywell ManualsCommercial Thermostats & Controls20K ohm NTC Immersion Temperature Sensor w/ 12 Ft insertion

INSTALLATION INSTRUCTIONS

62-0219

C7031J, C7041J,R

Averaging Sensors

C7031J, C7041J CABLE

C7041R RIGID COPPER

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a

hazardous condition.

2. Check ratings given in instructions and on the

product to ensure the product is suitable for your

application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

IMPORTANT

All wiring must agree with applicable codes,

ordinances and regulations.

MOUNTING

C7031J, C7041J Wire/Thermistor Averaging Sensors

and C7041R Rigid Copper Averaging can be mounted in

a duct to sense average air temperature.

IMPORTANT

Select a spot for the sensor to expose it to

average duct air temperature. Avoid locations

where stratification can cause sensing errors.

C7041R

C7031J,

C7041J

C7041B,C

Duct

C7031D,

C7041D

Immersion

C7031G,

C7041F

Outdoor

Be sure to take advantage of the entire line of quality Honeywell C7031/C7041 Sensors

C7041P

Button

Probe

C7041K

Strap-on

C7041R

Duct

Rigid

Copper

C7031J,

C7041J

Duct

Cable

AVERAGING

Summary of content (4 pages)

PAGE 1
C7031J, C7041J,R Averaging Sensors C7031J, C7041J CABLE C7041R RIGID COPPER INSTALLATION INSTRUCTIONS INSTALLATION When Installing this Product... 1. C7041R 2. 3. C7031J, C7041J 4. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition. Check ratings given in instructions and on the product to ensure the product is suitable for your application. Installer must be a trained, experienced service technician.
PAGE 2
C7031J, C7041J,R AVERAGING SENSORS C7031J, C7041J Mounting 1-11/16 (43) 1(25) 1-11/16 (43) 2-5/16 (59) 4-3/16 (107) 4 (70) 4 THERMISTORS PLACED ON A 12 FOOT (3.7M) WIRE. IMPORTANT To ensure that the C7031J/C7041J senses average duct temperature, position the temperature elements approximately as shown in Fig. 2. Do not allow the elements to touch or be close to the duct sides.
PAGE 3
C7031J, C7041J,R AVERAGING SENSORS C7041R Mounting 1-11/16 (43) 1 1-13/16 (46) 3-7/8 (99) 15/16 (23) 1-11/16 (43) 2-5/16 (59) 4-3/16 (107) 3/4 (19) 7/16 (12) 4 (70) 1/8 NPSM (3) 1 DEPENDING ON THE MODEL, THE ELEMENT LENGTH IS EITHER 12 FT (366 CM) OR 24 FT (732 CM). M22818 Fig. 4. C7031R dimensions in in. (mm). 1. Install two supports inside the duct to hold the averaging element. Cut a 7/8 in. (22 mm) hole in the side of the duct. Insert the averaging element into the duct through the hole.
PAGE 4
Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 customer.honeywell.com ® U.S. Registered Trademark © 2005 Honeywell International Inc. 62-0219 B.B.