Install Instructions

ManualsBrandsHoneywell ManualsCommercial Thermostats & Controls1097 ohm Electronic Temperature Sensor

Table Of Contents

INSTALLATION INSTRUCTIONS

62-0220-03

C7031G; C7041B,C,F,K; T775-SENS-OAT/STRAP

Series 2000 Electronic Temperature Sensors

C7031G, C7041F, T775-SENS-OAT OUTDOOR; STRAP-ON, C7041B,

C DUCT; C7031D, C7041D IMMERSION

SENSOR APPLICATIONS

Table 1. Electronic Sensor Application Guide

C7031D,

C7041D

C7031G, C7041F,

T775-SENS-OAT

C7041B,C

Strap-on

Model Application Output Element Insertion Length

C7031D Immersion 1097 ohms @ 77 F 5 in. (127 mm)

C7031G Outdoor 3484 ohms @ 77 F —

C7041B Duct 20 K ohm NTC @ 77 F 6 in. (152) or 12 in. (305 mm)

C7041C Duct 20 K ohm NTC @ 77 F 18 in. (457 mm)

C7041D Immersion 20 K ohm NTC @ 77 F 5 in. (127 mm)

C7041F Outdoor 20 K ohm NTC @ 77 F —

C7041K Strap-On 20 K ohm NTC @ 77 F —

T775-SENS-OAT Outdoor 1097 ohms @ 77 F —

T775-SENS-STRAP Strap-On 1097 ohms @ 77 F —

C7041B,C

Duct

C7031D,

C7041D

Immersion

C7031G, C7041F,

T775-SENS-OAT

Outdoor

Be sure to take advantage of the entire line of quality Honeywell Sensors

C7041P

Button

Probe

Strap-on

C7041R

Duct

Rigid

Copper

C7031J,

C7041J

Duct

Cable

Averaging

Summary of content (4 pages)

PAGE 1
C7031G; C7041B,C,F,K; T775-SENS-OAT/STRAP Series 2000 Electronic Temperature Sensors C7031G, C7041F, T775-SENS-OAT OUTDOOR; STRAP-ON, C7041B, C DUCT; C7031D, C7041D IMMERSION INSTALLATION INSTRUCTIONS C7031D, C7041D C7041B,C Strap-on C7031G, C7041F, T775-SENS-OAT SENSOR APPLICATIONS Table 1. Electronic Sensor Application Guide Model Application Output Element Insertion Length C7031D Immersion 1097 ohms @ 77 F 5 in.
PAGE 2
C7031G; C7041B,C,F,K; T775-SENS-OAT/STRAP SERIES 2000 ELECTRONIC TEMPERATURE SENSORS INSTALLATION — immersion well applications — strap-on applications When Installing this Product... 1. 2. 3. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition. Check the ratings given in the instructions and on the product to make sure the product is suitable for your application. Installer must be a trained, experienced service technician.
PAGE 3
C7031G; C7041B,C,F,K; T775-SENS-OAT/STRAP SERIES 2000 ELECTRONIC TEMPERATURE SENSORS Immersion Well Mounting (C7031D, C7041D) NOTE: The C7041D uses the 50001774-001 Well Assembly. See Fig. 5 for dimensions. Mount the C7031D/C7041D into the well: NOTE: Mounting using previously installed Honeywell wells (part no.: 32005960-001) requires an adapter (part no.: 50001775-001). The C7031D Sensor includes an immersion well. The C7041D Sensor does not include a well.
PAGE 4
C7031G; C7041B,C,F,K; T775-SENS-OAT/STRAP SERIES 2000 ELECTRONIC TEMPERATURE SENSORS Strap-on Mounting (C7041K, T775-SENSSTRAP) SENSOR The Sensor mounts on metal pipes from 1-5/8 inch to five inches in diameter using the straps supplied. Clean the pipe surface where the sensor makes contact before mounting. If necessary, remove pipe insulation at the installation point. Thermal compound is recommended. Locate the sensor on the discharge pipe within 3 ft. (0.9 m) of the boiler. See Fig. 6.