Operating Manual UtilityPRO Series TM Touchscreen Programmable Demand Control Thermostat 85-3126
BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen keys. To prevent damage to the thermostat, always press keys with your fingertip. This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Need Help? For assistance or warranty information please call your local Utility at the number found on the front of the thermostat.
Battery Replacement Battery Cover Assembly Coin cell battery tray Insert the coin cell battery in the coin cell battery tray and push it inside the battery cover assembly The UtilityPRO has a coin cell battery that retains the time and date during a power failure. Under normal circumstances the coin cell should last five years. Should the time and date need to be reset after a power failure, this is an indication that the coin cell needs to be replaced.
FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Class B limits are designed to provide reasonable protection against harmful interference in a residential installation.
UtilityPRO Series TM Table of contents About your new thermostat Special Features ...................................... 17 Screen Lock ............................................. 18 Screen Cleaning ....................................... 19 Advanced Functions ...........................20-23 Troubleshooting ..................................24-25 Thermostat Features.................................. 2 Getting Started Quick Reference to Controls .....................
Operating Manual UtilityProTM Features Congratulations! You’ve just purchased the world’s most advanced, easy-to-use thermostat. It has been designed to give you many years of reliable service and touchscreen climate control. Features • Provides Utility information messages. • Provides Utility billing information. • 5/1/1 and 5/2-day program schedules maximize comfort and economy. • Demand response thermostat programmed to aid you in your savings.
UtilityPRO Series TM Quick Reference to Controls Press day(s) to set program schedule (see page 11) Displays the current tier rate Press to adjust temperature settings Press to select fan operation Press to select system type SUN Press to set program schedule Press to override program schedule Press to view messages Press to set clock 3 Press to view the subscribed service messages Press to lock keypad for 30 seconds to clean screen
Operating Manual Quick Reference to Status Display Current inside temperature Fan setting Temperature setting TIER MEDIUM VIEW 75 Inside FAN AUTO System setting 8:10 HEAT SCHED Current day of week HOLD Program schedule ON (does not display when off) Following Schedule SUN SYSTEM Current time 70 Set To AM Recovery CLOCK SCREEN USAGE Adaptive Intelligent Recovery in effect (see page 17) Other display messages: • Cool ON: Cooling system is activated • Heat ON: Heating system is ac
UtilityPRO Series TM Demand Control This is an energy saving device. At times, thermostat operation may be temporarily adjusted by a small amount as outlined in your energy provider’s associated program literature. This is normal operation and is part of the program for which you have enrolled. Thank you for your participation.
Operating Manual ® UtilityPro Utility Usages Features Usage is a service provided by the utility provider. Depending on the various services provided by the utility provider, Usage may contain vital information for your use. It may display your electricity bill, water consumption bill, gas bill, and so on. Usage also has a feature wherein you can compare your present consumption against your last year’s consumption for the same time period.
UtilityPRO Series TM Getting View Messages Started Press on your screen. The message icon blinks when you receive a new message. Good Morning! The Message screen appears. Use the arrow buttons to view the messages. There can be a maximum of five messages. The message scrolls automatically if it has more than 21 characters. EXIT In case there are no messages, the message icon does not appear. Press Delete to delete the displayed message. Press Exit to go to the main screen.
Operating Manual TM UtilityPro Usage and Features Billing Press on your screen. ELECTRICITY BILL The Usage screen appears. Navigate using the arrow buttons to view the billing consumption of water, gas, electricity, and so on*. $ In case there are no utility messages, the utility message icon does not appear. 52 $ 61 EXIT Press Exit to go to the main screen. * subject to Contract Agreement with the Utility Provider.
UtilityPRO Series TM ® Getting UtilityPro Fan Settings Started Features Press FAN to select fan operation, then press DONE. 70 Inside FAN AUTO SYSTEM HEAT Set To 70 Following Schedule WED 6:01 SCHED • ON: Fan is always on. • Auto: Fan runs only when the heating or cooling system is ON. AM HOLD CLOCK SCREEN USAGE Press FAN Note: If a fan schedule is programmed, “Auto” runs the fan schedule.
Operating Manual System Settings Press the SYSTEM button to select one of the following, then press DONE. 70 Inside FAN AUTO SYSTEM HEAT Set To 70 SCHED • Cool: Thermostat controls only the cooling system. • Off: Heating and cooling systems are OFF. Following Schedule WED 6:01 • Heat: Thermostat controls only the heating system. AM HOLD CLOCK SCREEN • Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature.
UtilityPRO Series TM Schedule Settings Press SCHED SCHED HOLD CLOCK SCREEN USAGE Press EDIT DONE EDIT WAKE LEAVE Select day(s) RETURN SLEEP CANCEL Set heat/cool levels EDIT SCHEDULE SET SCHEDULE SAT MON-FRI SUN 70 HEAT Note: You can press CANCEL PERIOD to eliminate any unwanted time period. CANCEL PERIOD 6:00 DONE WAKE 78 AM LEAVE RETURN SLEEP 1. Press SCHED, then EDIT. 2. Press day buttons to select day(s). There are three groups (MON-FRI), (SAT), and (SUN). 3.
Operating Manual Program Schedule Override (Temporary) Adjust temperature 70 Inside FAN AUTO SYSTEM HEAT Set To The new temperature is maintained only until the next programmed time period begins (see page 15). For example, if you want to turn up the heat early in the morning, it will automatically be lowered later, when you leave for the day. 73 Heat On FRI 8:00 SCHED HOLD AM CLOCK SCREEN Press V or W to immediately adjust the temperature.
UtilityPRO Series TM Program Schedule Override (Permanent) Adjust temperature 70 Inside FAN AUTO SYSTEM HEAT Set To Press HOLD to permanently adjust the temperature. This turns off the program schedule. Whatever temperature you set is maintained 24 hours a day until you manually change it or press CANCEL (or SCHED) to cancel “Hold” and resume the program schedule.
Operating Manual Clock Settings Press CLOCK To set the current time display, press CLOCK, then press V or W to adjust the time. Press and hold V or W to advance the time more quickly. WED 6:01 SCHED AM HOLD CLOCK SCREEN Press DONE to save & exit (or press CANCEL to exit without changing the time). MORE Adjust time, then press DONE Note: The real-time clock should never require adjustment since it automatically updates for daylight savings time, and stores all date/time information.
UtilityPRO Series TM Save Money by Setting Program Schedules It is easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for weekdays and weekends. WAKE 6:00 am 70 ° LEAVE 8:00 am 62 ° RETURN 6:00 pm 70 ° SLEEP 10:00 pm 62 ° Set to the time you awaken and the temperature you want during the morning, until you leave for the day.
Operating Manual EnergyStar® Settings for Maximum Cost Savings This thermostat is pre-set to use EnergyStar program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%.
UtilityPRO Series TM Special Features Auto Changeover: When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Adaptive Intelligent Recovery: This feature allows the thermostat to “learn” how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set. For example: Set the Wake time to 6 am, and the temperature to 70°.
Operating Manual Screen Lock WED FAN AUTO SYSTEM HEAT SCREEN LOCKED 70 Inside 6:00 SCHED Set To 70 Following Schedule PM HOLD CLOCK SCREEN MORE To prevent tampering, the screen can be partially or fully locked. When partially locked, the screen displays SCREEN LOCKED for several seconds if a locked key is pressed. To unlock the screen, press any unlocked key while SCREEN LOCKED appears on the screen. When the screen is fully locked, no keys function.
UtilityPRO Series TM Screen Cleaning Press SCREEN WED 6:00 SCHED PM HOLD CLOCK SCREEN USAGE Screen lock timer (30 seconds) Clean Screen? Press SCREEN to go to the cleaning screen. Press OK to lock the screen for cleaning. The screen remains locked for 30 seconds so you can clean the screen without disturbing any settings. After 30 seconds, press CANCEL to resume normal operation, or press OK if you require more time for cleaning. Note: Do not spray any liquid directly on the thermostat.
Operating Manual Advanced Functions 2. Press and hold blank center key until the display changes. 1. Press SYSTEM. HEAT SUN 6:01 AM DONE SYSTEM CANCEL Function SUN Setting HEAT 3. Change settings as required (see pages 21-23). 0120 20 DONE 4. Press DONE to exit & save changes.
UtilityPRO Series TM Advanced Functions Year setting (first two digits) Function 0120 Options: Press V/W to change the first two digits of the year: 20 = Year 20xx 21 = Year 21xx Year setting (second two digits) Function 0130 Options: Press V/W to change the last two digits of the year: 01 - 99 (i.e., 2001 - 2099) Month setting Function 0140 Options: Press V/W to change the current month: 01 - 12 (i.e.
Operating Manual Advanced Functions Program schedule ON/OFF Function 0160 Options: Press V/W to turn the program schedule ON or OFF: 1 2 5/2 [programmable weekdays and weekends]. 5/1/1 [weekdays, saturday, and sunday programmable]. Temperature format (°F/°C) Function 0320 Options: Press V/W to set the temperature display format: 0 1 Fahrenheit Celsius Daylight savings time ON/OFF Function 0330 Options: The thermostat is pre-programmed to automatically adjust to daylight savings time.
UtilityPRO Series TM Advanced Functions Program schedule periods Function 0540 Options: Press V/W to set the number of program periods: 4 2 3 4-4 program periods (WAKE, LEAVE, RETURN, SLEEP) 2-2 program periods (WAKE and SLEEP) 3-2 program periods (LEAVE and RETURN) Clock format Function 0640 Options: Press V/W to set the clock display format: 12 12-hour clock (i.e., “3:30 pm”) 24 24-hour clock (i.e.
Operating Manual Troubleshooting If you have difficulty with your thermostat, please try the following. Most problems can be corrected quickly and easily. Display is blank • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is ON. • Make sure furnace door is closed securely. No response to key presses (or temperature does not change) • Check to make sure the thermostat is not locked (see page 18).
UtilityPRO Series TM Troubleshooting Heating or cooling system does not respond • Press SYSTEM to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press SYSTEM to set system to Cool. Make sure the temperature is set lower than the Inside temperature. Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is ON. Make sure furnace door is closed securely. If “Wait” is displayed, the compressor protection timer is ON.
Automation and Control Systems Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2007 Honeywell International Inc. US Patents pending 85-3126—1 Rev. M.S.
