NetAXS™ Access Control Unit User’s Guide If this panel is to be added to an existing loop, then all panels need to be upgraded. Please see www.honeywellaccess.com. April 2009 © 2009 Honeywell. All rights reserved.
Copyright© 2009 Honeywell. All rights reserved. All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this document at any time without prior notice. Microsoft and Windows are registered trademarks of Microsoft Corporation. Windows Server is a trademark of Microsoft Corporation.
CONTENTS What’s New in Release 3.1.8 Dynamic Screens and Performance Enhancements ..................................................................... ix Multi-language Support .................................................................................................................... ix CSV Reports and Card Upgrade ...................................................................................................... x Reverse IP ....................................................................
2.7 Configuring Other I/O & Groups Tab ..................................................................................... 52 2.7.1 Inputs Tab .............................................................................................................. 52 2.7.2 Outputs Tab ........................................................................................................... 55 2.7.3 Groups Tab ...........................................................................................................
LIST OF FIGURES Figure 1-1: NetAXS™ Web Server Hub Connection ................................................................ 2 Figure 1-2: NetAXS™ Web Server Direct Connection ............................................................. 3 Figure 2-1: NetAXS™ System Configuration Flow Chart ...................................................... 10 Figure 2-2: Configuration > System >Host/Loop Communications Tab ................................. 11 Figure 2-3: Configuration > System > General Tab ........
Figure 4-6: Status > Outputs > Doors/Aux/Other/DnStr Tab .................................................. 85 Figure 4-7: Status > Outputs > Groups Tab ............................................................................. 86 Figure 4-8: Status > System ..................................................................................................... 87 vi www.honeywell.
LIST OF TABLES Table 1-1: Reading the Select Panel ............................................................................................ 7 Table 2-1: Configuration > System > Host/Loop Communications Tab Field Descriptions..... 12 Table 2-2: Configuration > System > General Tab Fields ........................................................ 14 Table 2-3: Configuration > Time Management Tab Field Descriptions ...................................
viii www.honeywell.
What’s New in Release 3.1.8 Dynamic Screens and Performance Enhancements Dynamic screens are screens that can refresh data without re-submitting. In the Honeywell NetAXS™ panel, there is now a persistent connection between the web screens and the panel. This allows status updates from the panel to be pushed out to the screens automatically to display the data seamlessly on the screen. In addition to the dynamic screens, other panel-side enhancements have been made that improve screen performance.
CSV Reports and Card Upgrade CSV Reports and Card Upgrade A requested feature was added to the NetAXS™ panel to support card holder updates and additions to the database via a CSV (comma separated variable) file. In order to support this, a CSV report is first created via a request from the web page. This report can be edited directly or loaded into a spreadsheet to be edited. If loaded into a spreadsheet, the file can be saved in CSV format.
Connecting to the Web Server 1 In this chapter... Overview 1 Connecting to the Web Server 2 1.1 Overview A NetAXS™ access control site is configured with a host system and NetAXS™ access control units that exceed existing N-1000-III/IV, Pro Series specifications and approvals, and that communicate with each other and with a variety of input and output devices. Each access control unit, or panel, has four reader ports.
Connecting to the Web Server Connecting to the Web Server 1.2 Connecting to the Web Server This section describes how to connect a computer to the NetAXS™ web server via Ethernet and Internet Explorer. Notes: • The NetAXS™ panel that you are connecting to the computer is the Gateway panel. DIP switch 6 on a Gateway panel must be set to ON for a successful connection. • The Microsoft Windows™ screen captures used in this section reflect the Windows 2000™ platform.
Connecting to the Web Server Connecting to the Web Server Figure 1-2: NetAXS™ Web Server Direct Connection Terminal Ethernet Port Ethernet Cable NetAXS Panel 2. Configure the computer’s network connection: a. Select Start > Settings > Control Panel. b. Click Network and Dial-up Connections.
Connecting to the Web Server Connecting to the Web Server c. Identify your local Ethernet connection (commonly labeled Local Area Connection), and right click the icon to display the Local Area Connection Properties screen. d. Highlight the Internet Protocol (TCP/IP) connection. e. Click Properties to display your system’s current Internet Protocol properties. f. Important: Keep a record of your computer’s current network configuration as it appears in this screen.
Connecting to the Web Server Connecting to the Web Server j. Click OK to accept the entries. 3. Open your browser (Internet Explorer shown below), and enter https://192.168.1.150 as the target address.
Connecting to the Web Server Connecting to the Web Server 4. Press the Enter key to display the Honeywell NetAXS™ login screen. Note: If you are using Microsoft Internet Explorer 7, and you receive a certificate error message, follow these steps to clear it: a. Enter the IP Address of the panel into the URL box. b. Click Continue to the website (not recommended) to display the login screen. c. Click Certificate Error at the top-right of the IP Address. The “Untrusted Certificate” screen appears. d.
Connecting to the Web Server Reading the Select Panel 1.3 Reading the Select Panel The Select Panel is located at the right margin of the NetAXS™ web server main screen, shown in the preceding section. The presence of a number in one of the Select Panel cells indicates that its associated panel is online. For example, if you see a number 1 in a cell, this indicates that panel 1 is online.
Connecting to the Web Server Reading the Select Panel Table 1-1: Reading the Select Panel (continued) 8 Cell Display Status Large white number on blue background, such as “2” in the example below: Panel 2 is selected, and it has no unacknowledged alarms. Small white number on a red background, such as “1” in the example below: Panel 1 is not selected, but it does have unacknowledged alarms. www.honeywell.
Configuring via the Web Server 2 In this chapter...
Configuring via the Web Server Configuring the System 2.1 Overview This chapter explains the NetAXS™ configuration functions as accessed via the NetAXS™ web server. These functions should be performed only by the NetAXS™ system administrator or service personnel. Caution: The sequence of NetAXS™ configuration tasks is critical. If the sequence given below is not followed, the NetAXS™ system cannot be successfully configured.
Configuring via the Web Server Configuring the System 2.2 Configuring the System 2.2.1 Host/Loop Communications Tab In order to maintain your NetAXS™ system configuration or to monitor its status, you must connect to the NetAXS™ panel by using one of two modes: • Host mode (monitor only) – a host software system, such as WIN-PAK™, connects to the panel (through the NetAXS™ gateway panel, which has an on-board PCI communications adapter), and it enables you to monitor the status of the NetAXS™ system.
Configuring via the Web Server Configuring the System The Host/Loop Communications tab enables you to: • Configure the following host settings: – Connection type (host or web server) – Communications type – Baud rate – Port number – Time sync • Configure the loop baud rate for communication among downstream panels.
Configuring via the Web Server Configuring the System Table 2-1: Configuration > System > Host/Loop Communications Tab Field Descriptions (continued) Host/Loop Loop Setting Description Baud Rate Specifies the transmission rate (bits per second) between the host and the panel. Select the highest rate that your modem will support (19,200 bps is recommended). Port Number Specifies the port number for the Ethernet port (default is 3001).
Configuring via the Web Server Configuring the System 2.2.2 General Tab Click Configuration > System in the NetAXS™ menu to display the System Configuration (General) screen: Figure 2-3: Configuration > System > General Tab The General Tab enables you to: • Set the general configuration settings. • Reset the panel.
Configuring via the Web Server Configuring the System Table 2-2: Configuration > System > General Tab Fields Parameter Description Boot Time Displays the time that power was applied to the NetAXS™ panel. Reset Reboots the panel. A reset does not change the current configuration in the database. Anti-Passback Enabled – Enables anti-passback, which prevents an entrant to an area from passing his card back to another potential entrant.
Configuring via the Web Server Configuring the System Table 2-2: Configuration > System > General Tab Fields Parameter Description Duress Detect Enabled – Enables the user to trigger an alarm or output device in times of duress, such as when the operator is forced to grant access against his will to an unauthorized person. This feature is available only when the reader is configured with a “Card and Pin” access mode (see Reader Tab, page 31).
Configuring via the Web Server Configuring the System 2.2.3 File Management Tab Firmware is software that is embedded in the NetAXS™ board. The firmware provides this web interface and all access control functionality. Periodically, the firmware is updated. This tab enables you to download new versions of the firmware, revert to a previous version of the firmware, upload and/or download card and configuration databases.
Configuring via the Web Server Configuring the System Steps to reset the firmware version: 1. In the Active Image column, click to select the firmware version to which you want to revert. The prompt “Switching to an alternate firmware set requires a panel reboot” appears. 2. Click OK to reboot the panel. Steps to restore (or download) firmware: 1. Click Browse to locate the firmware file. 2. Click Download to download the selected firmware file.
Configuring via the Web Server Configuring the System Steps to download a card database report (.CSV file) from the host system to the panel: 1. Click Browse to locate the .CSV file. 2. Click Download to download the file. If the file is in the correct report format, this message appears: “Would you like to append or replace the database? Access Control does not function while replacing a database, and updating may take several minutes.
Configuring via the Web Server Configuring the System 2.2.4 Network Tab Your NetAXS™ panel is physically configured in one of a number of possible network configurations. See the “System Configuration” section in the NetAXS™ NX4L1 Installation Guide, NetAXS™ NX4S1 Installation Guide, and NetAXS™ NX4S2 Installation Guide for illustrations of the supported network configurations.
Configuring via the Web Server Configuring the System 2.2.5 Site Codes Tab Site codes identify an enterprise’s site. You can create a maximum of eight site codes to serve as secondary IDs (in addition to the card number) on the card for additional validation. Click Site Codes to display the Site Codes tab: Figure 2-6: Configuration > System > Site Codes Tab The Site Codes tab enables you to: • Create one or more site codes. • View existing site codes. • Modify an existing site code.
Configuring via the Web Server Configuring the System 2. Click Modify to display the Name and Site Code fields. 3. Modify the name or site code number as you desire, and click Modify again. Steps to delete a site code: 1. In the Num column, click the number of the site you want to delete. 2. Click Delete to display a prompt. 3. Click OK to delete the site code. Steps to delete all site codes: 1. Click Delete All Codes to display a prompt. 2. Click OK to delete the codes. 22 www.honeywell.
Configuring via the Web Server Configuring the System 2.2.6 Downstream Devices Tab The NetAXS™ downstream devices provide the NetAXS™ panel with additional inputs and outputs. The NetAXS™ panel supports two downstream board types: • NX4IN—Provides 32 supervised, four-state inputs that are limited to 2.2K ohms resistance. The NX4IN must be assigned network addresses 1 and 2. • NX4OUT—Provides two supervised inputs and 16 SPDT relay outputs; each input is limited to 2.2K ohms resistance.
Configuring via the Web Server Configuring the System 2.3 Configuring Time Management This set of time-related functions includes: • Setting the current time by which the panel will function. • Creating the time zones by which the panel will control the operation of the inputs, outputs, groups, readers, access levels, and cards through access levels. • Defining the holiday schedule. 2.3.
Configuring via the Web Server Configuring the System Steps: Use the descriptions in the following table to configure the time settings: Table 2-3: Configuration > Time Management Tab Field Descriptions Setting Description Current loop time Displays by default the current time setting in day/month/date/hour/minutes/seconds. For example: Fri Oct 31 07:16:27 2008. Format 12 hour – The 24-hour day is divided into two 12-hour halves, a.m. and p.m.; each half is numbered 1-12.
Configuring via the Web Server Configuring the System 2.3.2 Time Zones Tab The NetAXS™ panel controls access by using time zones, or time schedules. Inputs, outputs, groups, readers, access levels, and cards through access levels are all configured with time zones by which they will be energized or de-energized, enabled or disabled. For example, you might assign a group of outputs to be energized from 12:00 a.m. to 6:00 a.m. every day. The 12:00 a.m. to 6:00 a.m.
Configuring via the Web Server Configuring the System 4. If the time zone will be linked to another time zone, select the “linked to” time zone’s number from the drop down list. Caution: We recommend that you read the explanation of time zone linking below (see Linking Time Zones) before you link time zones. An example is provided to help you create the links successfully. 5. Click the Add Time Zone button. Steps to modify a time zone: 1.
Configuring via the Web Server Configuring the System Note: Time Zone 1 is reserved as a default with a time range of 24 hours, seven days a week. So, we need to add three time zones to the panel. Then, with the Link Time Zone feature, you can link them so that they all work together: 1. Add Time Zone 2 and select Monday, Tuesday, Wednesday, Thursday, and Friday. Enter a start time of 5:00 p.m.and an end time of 11:59 p.m. Leave the Link to Time Zone field blank. 2.
Configuring via the Web Server Configuring the System 2.3.3 Holidays Tab Holidays are days when no work is scheduled at the facility. These holidays are used in time zone configuration (see “Time Zones Tab“ on page 26). Click the Holidays tab: Figure 2-10: Configuration > Time Management > Holidays Tab The Holidays tab enables you to: • Create a holiday. • Modify a holiday. • Delete a holiday. Note: Holidays should be considered special days of a week.
Configuring via the Web Server Configuring the System While Annual is selected, the Year box is grayed out. The NX4 can support three different Holiday Types (Type 1, Type 2, and Type 3), but a user can only select one type per day. Also of note, a single calendar day cannot be set for more than one type of Holiday. For example, the 4th of July could be a Type 1 Holiday, but then Type 2 and 3 would not be able to work on the 4th of July.
Configuring via the Web Server Configuring the System 2.4 Configuring the Doors Each NetAXS™ panel supports four doors. For each door, you must configure the readers, inputs, and outputs. At Configuration > Doors in the task menu at the left margin of the NetAXS™ screen, click 1 to display the Door Configuration screen for door 1. Follow the same procedures below for doors 2, 3, and 4 for each panel. 2.4.1 Reader Tab A reader is a device that reads cards and either grants or denies access at the door.
Configuring via the Web Server Configuring the System • Define the time zone during which the reader will be in lockdown mode (see Time Zones Tab, page 26 for details about setting time zones). When the reader is in lockdown mode, entry is prevented but egress is still allowed. • Define the reader’s access mode (the combination of card and/or PIN entry required by the reader).
Configuring via the Web Server Configuring the System Steps: 1. Use the descriptions in the table below to configure the General reader settings. Table 2-4: Configuration > Doors > Reader Tab Descriptions Setting Description Access Mode Specifies the validation conditions required at the door before access is granted. For each access mode, you must also select a time zone from the drop down list. The time zone is the schedule by which the access mode is effective.
Configuring via the Web Server Configuring the System Table 2-4: Configuration > Doors > Reader Tab Descriptions Setting Description Anti-Passback Configures the anti-passback feature, which prevents an entrant to an area from passing his card back to another potential entrant. Note that anti-passback must first be enabled at the Configuration > System > General screen (see General Tab, page 14). Enabled – Enables the anti-passback feature.
Configuring via the Web Server Configuring the System Figure 2-12: Configuration > Doors > Reader > Card Formats Tab 3. Click to highlight each desired card format listed in the Available box, and click the green right arrow button to move the format(s) into the Selected box. Note: If you select no formats, the reader will function in legacy mode and the reader interprets the panel’s formats.
Configuring via the Web Server Configuring the System Table 2-5: Configuration > Doors > Reader > Card Format Fields (continued) Setting Description Concatenated Site Code Combines the Site Code and Card ID as one unique number. Total Num Bits Lists the total number of bits on the card. Even Parity Lists where on the card that even parity is being observed. Start Bit – first bit in the card where even parity begins.
Configuring via the Web Server Configuring the System Table 2-5: Configuration > Doors > Reader > Card Format Fields (continued) Setting Description Site Code A Lists where on the card the Site Code A is listed. Consult the card manufacturer for detail on the card detail. Start Bit – first bit in the card where the card’s Site Code begins. Num Bits – Number of bits to the right of the start bit, including the start bit, that comprise the Site Code. Most card formats require only Site Code A.
Configuring via the Web Server Configuring the System 2.4.2 Outputs Tab An output, or output relay, is a switch on the panel that either energizes or de-energizes or pulses an output device, such as a door lock or an LED. For example, a successful card read at a reader (input device) causes the output relay switch on the panel board to change the normal state of a door lock (output device), so that the normally locked door strike releases and permits entry.
Configuring via the Web Server Configuring the System the group configuration from this screen. To edit the Group configuration, click Configuration > Other in the side panel.
Configuring via the Web Server Configuring the System The LED Reader dialog box enables you to configure the Reader LED: The Outputs tab enables you to: • Configure the following for each of the door’s output locks and reader LEDs: – Name – Pulse time – Time zones – Latching – Interlock – Time zone card toggle – First card rule 40 www.honeywell.
Configuring via the Web Server Configuring the System Steps: Use the descriptions in the following table to configure each individual lock or Reader LED: Table 2-6: Configuration > Doors > Output Tab Field Descriptions Setting Description Name Enter a unique name to identify the device. Pulse Time Specifies the duration for which the device will assume abnormal status. For example, it specifies how long a horn will sound or a door strike will remain released.
Configuring via the Web Server Configuring the System 2.4.3 Inputs Tab Three inputs are associated with each of the four doors on a NetAXS™ panel: • Status – Provides the following door status information: • Egress – Allows the door to open or close normally without generating an alarm. • Tamper – Reports abnormal handling of the reader device or wiring. Click to display the Inputs tab: Figure 2-15: Configuration > Doors > Inputs Tab Note that there are four possible Mode configurations.
Configuring via the Web Server Configuring the System The Inputs tab enables you to: • Define the Status, Egress, and Tamper inputs’ access modes. • Specify the Status, Egress, and Tamper shunt time, or the period of time the door’s normal state will be ignored. • Specify the Status, Egress, and Tamper debounce time, or the period of time the input must remain in its new state before it is recognized as being in the new state. • Specify the time zones for the Status, Egress, and Tamper inputs.
Configuring via the Web Server Configuring the System Steps: Use the descriptions in the table below to configure the Status, Egress, and Tamper inputs, then click Submit Changes: Table 2-7: Configuration > Doors > Inputs Tab Field Descriptions Setting Mode Description Normally Closed – Specifies that the door’s normal state is closed. Normally Open – Specifies that the door’s normal state is open.
Configuring via the Web Server Configuring the System 2.5 Configuring Access Levels Every card is assigned an access level. The access level specifies the time zone, or time schedule, during which the card holder can be granted access at a specific door. For example, an access level embedded in an employee’s card might allow the employee to enter the facility only through door 2 from 6:00 a.m. to 6:00 p.m., Monday through Friday.
Configuring via the Web Server Configuring the System Steps to create an access level: 1. Select the door(s). The access level will allow access only at the door(s) you select here. 2. Enter the name of the access level in the Name field. This should be a unique name that identifies the general user group. 3. Select the time zone you want from the drop down list in the Time Zone field. The access level will allow access to the card holder only during this time zone. 4. Click the Add Level button.
Configuring via the Web Server Configuring the System 2.6 Maintaining Cards A card is encoded with a unique number and the card holder’s rights to access NetAXS™ system resources. For example, in addition to its unique number, a card would allow the card holder to be granted access to certain doors during a certain time of day. 2.6.
Configuring via the Web Server Configuring the System – – – – Use limits Card holder note 1 Card holder note 2 Access levels Steps: Use the field descriptions in the following table to complete the card fields and click Add Card(s): Table 2-8: Cards > Add Cards Field Descriptions 48 Field Description Card Number(s) Specifies the unique number by which the card holder will be identified. A card number is required. Card Holder Name Identifies the card holder.
Configuring via the Web Server Configuring the System 2.6.2 Displaying and Modifying Cards Use this function to display specified cards and modify them. Click Cards > Card Data to display the search screen with which you can find and display specified cards. Figure 2-18: Cards > Card Data The Display or Modify Card(s) screen enables you to: • Display cards by searching on any of the following keys: – Card number – Card holder’s last name • Modify the displayed card(s) Steps: 1.
Configuring via the Web Server Configuring the System 2.6.3 Deleting Cards Click Cards > Delete Card(s) to display the Delete Cards screen: Figure 2-19: Cards > Delete Cards The Delete Card(s) screen enables you to: • Delete cards retrieved by any of the following keys: – Card number – Range of card numbers – Card holder’s last name Steps: 1. Enter a value for any of the search keys (card number, card number range, or cardholder name). 2.
Configuring via the Web Server Configuring the System 2.6.4 Displaying Reports Use this function to display a report of all cards and card data. You can display the cards either by the cardholder’s last name or by the card number. Click Cards > Reports to display the Card Reports screen. The Card Reports screen enables you to: • View card records by the cardholder’s last name. • View card records by the cards’ numbers. Steps: 1.
Configuring via the Web Server Configuring the System Table 2-9: Cards > Reports Field Descriptions (continued) Field Description Activation Date Shows the date the card was activated. Expiration Date Shows the date the card expires. Use Limit Indicates the number of times the card will be granted access. APB State Indicates whether or not anti-passback is enabled on the card. Note 1 Displays informational text that may have been entered in the Note 1 field.
Configuring via the Web Server Configuring the System Click Inputs to display the Inputs screen: Figure 2-20: Configuration > Other I/O & Groups > Inputs Tab The Input tab enables you to: • Configure the mode, debounce time, and time zones for another input (input 13 and input 14). • Configure the mode, shunt time, debounce time, time zones, and auto-relock for the downstream inputs provided by downstream input/output boards (NX4IN or NX4OUT).
Configuring via the Web Server Configuring the System Steps: Use the descriptions in the following table to configure other panel inputs and downstream inputs: Table 2-10: Configuration > Other I/O & Groups > Inputs Tab Field Descriptions Setting Description Name Enter a unique name to identify the device. Mode Normally Closed – Specifies that the door’s normal state is closed. Normally Open – Specifies that the door’s normal state is open.
Configuring via the Web Server Configuring the System 2.7.2 Outputs Tab This tab enables you to configure the four NetAXS™ auxiliary outputs (outputs 5-8) that are physically located on the panel board, and the outputs on downstream NX4OUT boards daisy-chained to Terminal Block 10. A NetAXS™ panel supports a maximum of four NX4OUT boards, and each board provides two inputs and 16 outputs. The downstream outputs are numbered 17-80.
Configuring via the Web Server Configuring the System Steps: Use the descriptions in the following table to configure each output device: Table 2-11: Configuration > Other I/O & Groups > Outputs Tab > Fields 56 Setting Description Name Enter a unique name to identify the device. Pulse Time Specifies the duration for which the device will assume abnormal status. For example, it specifies how long a horn will sound or a door strike will remain released. The maximum number of hours is 1.
Configuring via the Web Server Configuring the System 2.7.3 Groups Tab This tab enables you to configure outputs in groups. For example, you might want a group of horns in your facility to sound for the same duration or to be enabled or disabled according to the same schedule, or time zone. You might want a group of doors to be energized or de-energized during the same time zone. A NetAXS™ web server supports up to 64 output groups.
Configuring via the Web Server Configuring the System Steps: Use the descriptions in the following table to configure each group: Table 2-12: Configuration > Other I/O & Groups > Groups Tab Field Descriptions 58 Setting Description Name Enter a unique name to identify the group. Pulse Time Specifies the duration for which the device will assume abnormal status. For example, it specifies how long a horn will blow or a door strike will remain released. The maximum number of hours is 1.
Configuring via the Web Server Configuring the System 2.8 Configuring Interlocks An interlock is a programmed connection between two points. The interlock causes an input point, output point, or group of output points to act in a specified manner when another input point, output point, or group of output points changes its state. An action on one point cause a reaction from a second point on the same panel or attached downstream board.
Configuring via the Web Server Configuring the System Steps to create an interlock: 1. Click the New Interlock button to display the screen. 2. Use the descriptions in the following table to configure the interlock: Table 2-13: Configuration > Interlocks > Field Descriptions Interlock element Description Trigger Specifies the input, output, or output group for which a change of state will cause a reaction from another input, output, or group.
Configuring via the Web Server Configuring the System Steps to enable/disable an interlock: 1. To enable an interlock, click the Enable button. 2. To disable an interlock, click the Disable button. 2.9 Configuring Users A user is one who will be using the NetAXS™ software interface in one or more of the following functional roles: • Operator – Monitors the system’s operation. The Operator user can perform the following tasks: – View (only) panel I/O status, alarms, events, and card database.
Configuring via the Web Server Configuring the System .Click Users to display the User Configuration screen: Figure 2-24: Configuration > Users The User Configuration screen enables you to: • Create a user. • Modify a user. • Delete a user. • Enable and disable a user account. • View the user’s current login status, either logged in or logged out. Steps to create a user: 1. Click the New User button. 2. Enter the user’s name in the Name field (at least five characters). 3.
Configuring via the Web Server Configuring the System 5. Select the Account Status: – Enabled – Activates the user account (the user can log in). – Disabled – De-activates the user account (the user cannot log in). 6. Select the user’s Language Preference from the dropdown list. 7. Click the Add User button. Steps to modify a user: 1. In the User Name field, click the name of the user you want to modify. 2. Change the name, password, account type, or account status. 3. Click the Modify button.
Configuring via the Web Server Configuring the System 64 www.honeywell.
3 Configuring via WIN-PAK In this chapter... Overview 65 Adding a New NetAXS™ Panel 66 3.1 Overview This chapter explains the NetAXS™ configuration functions as accessed via the Quick Start Wizard (QSW) in WIN-PAK 2005, WIN-PAK PRO 2005, WIN-PAK SE, and WIN-PAK PE. The QSW creates the ADV options and adds the panel to the Control Map and the Master Access Level. These functions should be performed only by the NetAXS™ system administrator or service personnel. Notes: • WIN-PAK 2.
Configuring via WIN-PAK Adding a New NetAXS™ Panel The NetAXS™ Gateway panel’s baud rate is set configured via the NetAXS™ web server (see the NetAXS™ Access Control Unit Installation Guide for instructions). When you set the Loop Type in the QSW to 485 ACK-NAK, you define the baud rate to be 19.2 kilobits per second. This baud rate and the panel’s baud rate must match to communicate properly.
Configuring via WIN-PAK Adding a New NetAXS™ Panel 3.2.2 Configuring the Panel Manually Use the WIN-PAK Panel Configuration screen to complete the NetAXS™ panel configuration manually. All of the configuration screen options are supported for NetAXS™ panel configuration, except where they are noted otherwise in this section. You cannot initialize the NetAXS™ panel from the WIN-PAK Control Map until you complete the steps in this section.
Configuring via WIN-PAK Adding a New NetAXS™ Panel 3. Add the ADV. 4. Click OK. 5. Display and complete the Card Format tab: Figure 3-3: WIN-PAK Panel Configuration Screen - Card Format Tab 68 www.honeywell.
Configuring via WIN-PAK Adding a New NetAXS™ Panel 6. Display and complete the Time Zones tab: Figure 3-4: WIN-PAK Panel Configuration Screen - Time Zones Tab Note: All Time Zones and Holidays are supported for a NetAXS™ panel.
Configuring via WIN-PAK Adding a New NetAXS™ Panel 7. Display and complete the Options tab: Figure 3-5: WIN-PAK Panel Configuration Screen - Options Tab Notes: • All options are supported for a NetAXS™ panel except the Advanced U option. When using Groups, you must select both AEP boards in the Hardware Options box. The NX4OUT board functions as two AEP-3 boards, and it provides outputs 17-32.
Configuring via WIN-PAK Adding a New NetAXS™ Panel 8. Click the Advanced button to display the Advanced Options screen, and select the desired advanced options. Note that the Advanced U option is not supported for the NetAXS™ panel. 9. Display and complete the Inputs tab. If you are using the NetAXS™ inputs to monitor the door status or activate a request to exit, then you must reassign the interlocks as indicated below.
Configuring via WIN-PAK Adding a New NetAXS™ Panel 10.Use the following procedure to reassign the interlocks: a. Display the Readers tab, and then display the first input’s configuration window. Select None, and click OK. This dissolves all input interlocks and changes the Shunt Time to 0. This allows the input to be properly redefined for use with NetAXS. b. Repeat the preceding step for each input for each reader on this tab. c.
Configuring via WIN-PAK Adding a New NetAXS™ Panel Table 3-1: Interlock Reassignments for NetAXS™ (continued) Interlock Function 12 Reader 4 tamper/auxiliary. 13 Primary power status - external (or General input). There is also a system primary power alarm 17 that reports through the ADV and is not a wired port. 14 Tamper (or General input).
Configuring via WIN-PAK Adding a New NetAXS™ Panel 11.The configuration of a NetAXS™ panel via WIN-PAK is now complete. Configuration is optional on the Outputs and Groups tabs. 74 www.honeywell.
4 Monitoring NetAXS™ Status In this chapter... Overview 75 Monitoring Alarms 76 Monitoring Events 79 Monitoring Inputs 82 Monitoring Outputs 85 Monitoring System Status 87 4.1 Overview This chapter is written for the NetAXS™ operator who will monitor the following NetAXS™ status: • Alarms – Alarms are events, or system transactions, that have been assigned alarm status. These often include events such as an invalid card read or a forced door.
Monitoring NetAXS™ Status Monitoring Alarms 4.2 Monitoring Alarms Alarms are viewed as system-generated messages that may indicate the need for user attention. From the drop down menu at the upper-right corner of each Alarms tab, you can configure the tab to display alarms in groups of 10, 25, 50, or 75.
Monitoring NetAXS™ Status Monitoring Alarms Click the Acknowledged tab to display the acknowledged alarms: Figure 4-2: Status > Alarms > Acknowledged Tab The following table describes the information displayed on both the Unacknowledged alarms tab and Acknowledged alarms tab: Table 4-1: Status > Alarms Field Descriptions Column Head Description Ack (Unacknowledged tab only) Enables you to select any or all of the alarms that you want to acknowledge.
Monitoring NetAXS™ Status Monitoring Alarms Table 4-1: Status > Alarms Field Descriptions (continued) Column Head Description Date/Time (ID) Identifies the date and time the alarm was generated. Device Name [ID] Identifies the device that generated the alarm. LN Logical device number – the unique name or number given to the alarm-generating device when the device was configured in Configuration > Doors. PN Physical device number – the unique number assigned to the device on the NetAXS™ board.
Monitoring NetAXS™ Status Monitoring Events 4.3 Monitoring Events The Events page monitors both panel- and web-generated events. For example, a panel event is the reading of a card by a reader. A web event example is a user logon. Click Status > Events to display the Panel event tab: Figure 4-3: Status > Events > Panel Tab Notes: • You can display the oldest events first by clicking Oldest at the bottom of the tab, or display the newest events first by clicking Newest.
Monitoring NetAXS™ Status Monitoring Events The following table describes the information displayed on the Panel events tab: Table 4-2: Status > Events > Panel Tab Field Descriptions Column Head Description Date/Time [ID] Provides the date and exact time the event was generated, according to the panel’s name. Device Name [ID] Identifies the device that generated the event.
Monitoring NetAXS™ Status Monitoring Events Click Status > Events > Web to display the Web events tab: Figure 4-4: Status > Events > Web Tab Note: The number of active users is indicated in the upper left corner of the tab.
Monitoring NetAXS™ Status Monitoring Inputs 4.4 Monitoring Inputs A NetAXS™ panel supports door, panel, and auxiliary inputs. The door inputs provide egress and tamper status, the panel inputs provide power fail and tamper status, and the auxiliary inputs support any downstream status. Click Status > Inputs to display the Input Status screen: Figure 4-5: Status > Inputs The Input Status screen enables you to: • View the current status of each input (Normal, Alarm, Cut, Short, Shunted).
Monitoring NetAXS™ Status Monitoring Inputs Steps: 1. To shunt or un-shunt an input, click the input name to display a prompt. Click OK to complete the shunt or un-shunt.
Monitoring NetAXS™ Status Monitoring Inputs 2. To restore the input to its shunt state based on its configured time zone, click the input’s Restore to Time Zone button to display a prompt. Click OK to complete the restoration to the configured time zone. Note: 84 The Input Status screen dynamically refreshes when input status changes. www.honeywell.
Monitoring NetAXS™ Status Monitoring Outputs 4.5 Monitoring Outputs An output is an output device that changes its normal state when it is energized, pulsed, or time-zone controlled. For example, a successful card read at a reader pulses a door lock. The lock changes its normally locked state to an unlocked state and the cardholder opens the door. A NetAXS™ panel supports one output for each of its four doors. The panel also supports four additional outputs for auxiliary devices and 64 downstream outputs.
Monitoring NetAXS™ Status Monitoring Outputs Click Status > Outputs > Groups to display the Groups tab of the Output Status screen: Figure 4-7: Status > Outputs > Groups Tab The Output Status tab enables you to: • View the current status of each output in the Discrete tab (Energized or De-energized). • View the current status of each output group in the Groups tab. • Energize or de-energize any output or group indefinitely. • Pulse any output.
Monitoring NetAXS™ Status Monitoring System Status 4.6 Monitoring System Status This feature provides basic monitoring of objects in the NetAXS™ system other than alarms, events, inputs, and outputs. Click Status > System to display the System Status screen: Figure 4-8: Status > System The System Status screen enables you to: View the following status of system objects other than alarms, events, inputs, and outputs: • Number of currently configured instances of the object.
Monitoring NetAXS™ Status Monitoring System Status 88 www.honeywell.
Upgrading NetAXS™ Firmware A A.1 Overview This appendix provides instructions for upgrading NetAXS™ firmware to release 3.1.8. This version is a new release; it replaces all builds of releases 1 and 2, and it includes all functionality provided in NetAXS™ releases 1 and 2. See “What’s New in Release 3.1.8“ on page ix for a description of the new features included in release 3.1.8. This release package includes three components: • 1-NetAXSupdaterApp.bin—updater file. • 2-NetAXSOSimage363.
Upgrading NetAXS™ Firmware NetAXS™ Release 3.1.8 Upgrade Procedure Release 3 has a new access-level database; therefore, any release 3 access-level database changes will not take effect until the entire loop is upgraded to release 3. A.2.3 Uploading Data from the Panel Note: Before you upgrade a web-based panel, we recommend that you back up your databases. The upgrade scripts bring all your panel data forward into the new version without the need for user intervention.
Upgrading NetAXS™ Firmware NetAXS™ Release 3.1.8 Upgrade Procedure Note: For WIN-PAK systems, we recommend that you stop the “communications server service” while upgrading, and then restart the service after your panels are upgraded. 2. Connect to your gateway panel using the instructions from the NetAXS™ Access Control Unit User’s Guide, section 1-2, “Connecting to the NetAXS™ Web Server.
Upgrading NetAXS™ Firmware NetAXS™ Release 3.1.8 Upgrade Procedure 8. Install the new application file, 3-NetAXSimage03.01.08.bin. To do this: a. Select the Configuration > System > File Management tab. b. In the Download box, click Browse to locate the file, 3-NetAXSimage03.01.08.bin. c. Select the file and click Download. Click OK to continue. After the “Download complete” message appears, click OK again. The “Download image” message appears and tells you to wait five minutes while NetAXS™ reboots. d.
Upgrading NetAXS™ Firmware NetAXS™ Release 3.1.8 Upgrade Procedure i. Click OK. j. Close the web browser and re-open it. k. Enter the IP Address again into the URL box. The login screen appears without the certificate error A.2.6 Clearing the Cache in the Internet Browsers Used by the NetAXS™ Web Server The NetAXS™ panel supports Internet Explorer 7 (IE7), Internet Explorer 6 (IE6), Firefox 2, and Firefox 3. For all browsers, we recommend that you clear the cache after a successful upgrade.
Upgrading NetAXS™ Firmware NetAXS™ Release 3.1.8 Upgrade Procedure 94 www.honeywell.
Index A Access level 2-45 Access mode 2-33 Acknowledged alarms 4-77 Administrator 2-61 Alarms 4-75, 4-76 acknowledged 4-77 monitoring 4-76 Anti-passback 2-15, 2-34 Auto-relock 2-44, 2-54 Auxiliary outputs 2-55 B Baud rate host 2-13 loop 2-13 C Card and PIN duress detect 2-16 Card formats 2-34 for WIN-PAK configuration 3-68 Cardholder notes 2-16 Cards access levels 2-45 adding 2-47 card formats 2-34 card type 2-48 cardholder notes 2-16 deleting 2-50 displaying 2-49 modifying 2-49 PIN 2-48 reports 2-51 sit
Index Downstream baud rate 2-13 force baud reset 2-13 inputs 2-52 outputs 2-55 Downstream devices 2-23 Duress detect 2-16 E Egress 2-42 Energizing 2-26 Events 4-75, 4-79 F File management 2-17 Firmware downloading 2-17 for WIN-PAK configuration 3-67 reverting to previous 2-17 First card rule 2-41 Force baud reset 2-13 G Gateway panel 1-2, 2-15 Groups 2-57 H Holidays (see also Time Zones) 2-29 Host 2-11 Host baud rate 2-13 Host connection 2-12 Host mode monitoring 2-11 I Inputs 2-42, 4-75 AC Power Fail
Index NX4IN/NX4OUT boards 2-55 NX4IN/NX4OUTboards 2-52 O Operator 2-61 Output relay 2-38 Outputs 2-38, 4-75 auxiliary 2-55 de-energizing 4-86 downstream 2-23 energizing 4-86 groups 2-57 interlock 2-56 interlocks 2-59 latching 2-56 monitoring 4-85 pulsing 4-86 re-setting 4-86 P Panel status 1-7 Panels addresses 2-15 configuring via WIN-PAK 3-66 downstream baud rate 2-13 gateway 2-15 reboot 2-15 reset 2-15 setting current time 2-24 PIN 2-48 Port number 2-13 Pulse time 2-41, 2-56 Q Quick Start Wizard 3-66
Index U Unsupervised 2-43, 2-44 Uploading card and configuration data 2-17 Use limits 2-48 Users 2-61 W Web mode monitoring and configuring 2-11 Web server 1-1 Web server connection 1-2 direct 1-3 hub 1-2 Web session timeout 2-15 Index-4 www.honeywell.
Honeywell Access Systems 135 W. Forest Hill Avenue Oak Creek, WI 53154 United States 800-323-4576 414-766-1798 Fax www.honeywellaccess.com Specifications subject to change without notice. © Honeywell. All rights reserved.
