Voyager™ XP 1472g Series Cordless Area-Imaging Scanner Quick Start Guide VG1472-EN-QS-01 Rev (a) 6/10
Note: Refer to your user’s guide for information about cleaning your device. For localized language versions of this document, go to www.honeywellaidc.com. Getting Started Turn off the computer’s power before connecting the base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the scanner in the base to establish a link. The green LED on the base flashes to indicate the scanner’s battery is charging.
USB Connection: Keyboard Wedge Connection:
RS232 Serial Port Connection: RS485 Connection:
Reading Techniques The view finder projects an aiming dot that should be centered over the bar code, but it can be positioned in any direction for a good read. Hold the scanner over the bar code, pull the trigger, and center the aiming dot on the bar code. The aiming dot is smaller when the scanner is closer to the code and larger when it is farther from the code. Hold the scanner close to smaller bar codes, and farther away from large bar codes to get a proper read. If the bar code is highly reflective (e.
RS485 Interface The RS485 interface defaults to port 5B. If you have an IBM POS terminal using port 9B, scan the appropriate code below to program the terminal, then power cycle the cash register. IBM Port 9B HHBCR-1 Interface IBM Port 9B HHBCR-2 Interface Note: For additional RS485 interface selections, see the User’s Guide for your product. USB Serial Scan the following code to program the scanner to emulate a regular RS232-based COM Port.
USB PC Keyboard Scan the following code to program the scanner for a USB PC Keyboard. USB PC Keyboard Keyboard Country Scan the appropriate country code that follows to program the keyboard layout for your country or language. By default, national character replacements are used for the following characters: #$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart in your User Guide to view the character replacements for each country.
France
Germany/Austria Great Britain Italy Norway Spain Switzerland Note: For a complete list of country codes, see the User’s Guide for your product.
Locked Link If you link a scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into the base, it will charge the scanner, but the scanner will not be linked. Locked Link Mode (Single Scanner) To use a different scanner, you need to unlink the original scanner by scanning the Unlink Scanner bar code.
Trigger The following bar codes will allow you to use the scanner in Manual Trigger - Normal Mode (need to press the trigger to read) or Presentation mode (the scanner is activated when it “sees” a bar code). Manual Trigger - Normal (Default) Presentation Mode Suffix If you want a carriage return after the bar code, scan the Add CR Suffix bar code. To add a tab after the bar code, scan the Add Tab Suffix bar code. Otherwise, scan the Remove Suffix bar code to remove the suffixes.
Add Code ID Prefix to all Symbologies Scan the following bar code if you wish to add a Code ID prefix to all symbologies at once. Add Code ID Prefix To All Symbologies (Temporary) Note: For a complete list of Code IDs, see the User’s Guide for your product. Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in your User’s Guide.
Step 1. Scan the Enter Data Format symbol. Primary/Alternate Format: scan 0 for Primary Format Terminal Type: scan 099 for any terminal type Code I.D.: scan 99 for any bar code type Length: scan 9999 for any length bar code. Editor commands: use the Programming Chart that follows. Step 7. Scan Save to save your entries. Step 2. Step 3. Step 4. Step 5. Step 6.
Programming Chart 0 1 2 3 4 5 6 7 8 9
A B C D E F Save EZConfig-Scanning To access additional features for the scanner, use EZConfigScanning, an online configuration software tool, available from ourwebsite.
Support To search our knowledge base for a solution or to log into the Technical Support portal and report a problem, go to www.hsmcontactsupport.com. Documentation Product documentation is available at www.honeywellaidc.com. Limited Warranty For warranty information, go to www.honeywellaidc.com and click Get Resources > Product Warranty. Patents For patent information, see www.hsmpats.com. Disclaimer Honeywell International Inc.
1472-ML-RS-01 Rev (a) Voyager™ XP 1472g Area-Imaging Scanner Agency Model: 1472g La documentación del producto está disponible en www.honeywellaidc.com. Product documentation is available at www.honeywellaidc.com. La documentation sur le produit est disponible à www.honeywellaidc.com. La documentation du produit est disponible sur le site www.honeywellaidc.com. La documentazione sul prodotto è disponibile sul sito www.honeywellaidc.com. Die Produktdokumentation ist unter www.honeywellaidc.
Originalmente, este documento se creó y redactó en inglés. En caso de que se traduzca a otro idioma y surja un conflicto entre la versión en inglés y la versión en otro idioma, prevalecerá la versión en inglés. Se reconoce y admite que, en la versión en inglés, expresa la intención de las partes con más claridad. Cualquier aviso o comunicación proporcionada en relación con este documento debe incluir una versión en inglés. Este documento se preparó y redactó en inglés.