Hyperion 1300g General Purpose Handheld Linear Scanner User’s Guide ™
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Table of Contents Chapter 1 - Getting Started About This Manual ...................................................... 1-1 Unpacking the Scanner ............................................... 1-1 Connecting with USB .................................................. 1-1 Connecting with Keyboard Wedge .............................. 1-2 Connecting with RS-232 Serial Port............................ 1-3 Connecting with RS485............................................... 1-3 Reading Techniques ...............
RS232 Modifiers ........................................................ 2-22 RS-232 Baud Rate............................................... 2-22 RS-232 Word Length: Data Bits, Stop Bits, and Parity 2-23 RS-232 Handshaking................................................. 2-24 RS232 Timeout .................................................... 2-27 XON/XOFF .......................................................... 2-27 ACK/NAK .............................................................
Output Sequence Overview ...................................... 3-10 To Add an Output Sequence............................... 3-10 Other Programming Selections ........................... 3-10 Output Sequence Editor ...................................... 3-11 Output Sequence Editor ...................................... 3-13 Require Output Sequence................................... 3-13 Multiple Symbols ....................................................... 3-13 No Read ...................................
Data Format Editor Commands ................................... 5-4 Send Commands ................................................... 5-4 Move Commands................................................... 5-7 Search Commands ................................................ 5-8 Miscellaneous Commands................................... 5-10 Data Format Editor .............................................. 5-14 Data Formatter.....................................................
All Symbologies........................................................... 6-2 Codabar Start/Stop Characters ............................ 6-3 Codabar Check Character..................................... 6-4 Codabar Concatenation ........................................ 6-5 Codabar Message Length ..................................... 6-6 Code 39 Start/Stop Characters............................. 6-7 Code 39 Check Character..................................... 6-7 Code 39 Message Length ......................
UPC E0 Addenda ................................................ 6-31 EAN/JAN 13 Check Digit ..................................... 6-32 EAN/JAN 13 Addenda ......................................... 6-33 EAN/JAN 13 Addenda Required.......................... 6-33 EAN/JAN 13 Addenda Separator ........................ 6-34 ISBN Translate .................................................... 6-34 EAN/JAN 8 Check Digit ....................................... 6-35 EAN/JAN 8 Addenda ...................................
Trigger Commands ..................................................... 9-4 Resetting the Standard Product Defaults .................... 9-4 Menu Commands ........................................................ 9-5 Chapter 10 - Product Specifications Hyperion 1300g Product Specifications .................... 10-1 Standard Connector Pinouts ..................................... 10-2 Chapter 11 - Maintenance Repairs ...................................................................... 11-1 Maintenance.....
viii
1 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Hyperion 1300g. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. For additional USB programming and technical information, refer to the Honeywell “USB Application Note,” available at www.honeywellaidc.com. Connecting with Keyboard Wedge A scanner can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection: 1.
Connecting with RS-232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. only if power supply is included 3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. 4. Once the scanner has been completely connected, power up the computer. 5. This interface programs 38,400 baud, 8 data bits, no parity, and 1 stop bit.
1. Connect the appropriate interface cable to the device, then to the computer. 2. Turn the terminal/computer power back on. The scanner beeps. 3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. 4. For further RS485 settings, refer to RS485 on page 2-2. Reading Techniques The scanner has a bright red aiming beam that corresponds to its horizontal field of view.
The best focus point for reading most code densities is about 5 inches (12.7 cm) from the unit. To read a single bar code or multiple bar codes (on a page or on an object), hold the scanner at an appropriate distance from the target, pull the trigger, and center the aiming beam on the bar code. Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner.
The Serial Programming Commands starting on page 9-1 lists the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
2 Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below.
RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. Option Setting Baud Rate Data Format 38,400 bps 8 data bits, no parity bit, 1 stop bit RS232 Interface RS485 Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface.
Each bar code above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 EAN 13 UPC A UPC E 0C 16 0D 0A Code 39 Interleaved 2 of 5 Code 128 * Code 128 ** 00 00 00 00 0A 0D 0A 18 0B 0B 0B 0B * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces **Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface OPOS Mode The following bar code configures your scanner for OPOS (OLE for Re
OPOS Mode USB IBM SurePos Scan the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) interface. Note: After scanning the code below, you must power cycle the cash register.
USB PC or Macintosh Keyboard Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF. USB Keyboard (PC) USB Keyboard (Mac) USB HID POS Scan the following code to program the scanner for USB HID POS bar code scanners. USB HID POS Bar Code Scanner USB Serial Commands USB Serial Emulation Scan the following code to program the scanner to emulate a regular RS232based COM Port.
CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Character RTS/CTS with timeout and 232 ACK/NAK are also enabled.
Datalogic™ Magellan® Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Datalogic Magellan bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Datalogic Magellan Bioptic Settings Note: If you are having unexpected results with this programming code, scan the Resetting the Custom Defaults bar code on page 1-5 first, then scan the programming code above.
Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ * United States Albania Arabic Azeri (Cyrillic) Azeri (Latin) Belarus Belgium Bosnia 2-8
Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) China Croatia 2-9
Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland 2 - 10
France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) 2 - 11
Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Ireland Italian (142) Italy 2 - 12
Japan ASCII Kazakh Korea Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) 2 - 13
Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania 2 - 14
Russia Russian (MS) [ Russian (Typewriter) SCS Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) 2 - 15
Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Thailand Turkey F 2 - 16
Turkey Q Ukrainian United Kingdom United Stated (Dvorak right) United States (Dvorak left) United States (Dvorak) United States (International) Uzbek (Cyrillic) Vietnam 2 - 17
Keyboard Mode Options ALT Mode If your bar code contains special characters from the extended ASCII chart for example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII Characters on page A-6.) Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code. If your keystrokes require the ALT key and 4 characters, scan the 4 Characters bar code. The data is then output with the special character(s). Default = Off.
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only). This selection can only be used with systems that have an LED, which notes the Caps Lock status. Automatic Caps Lock Autocaps via NumLock bar code should be scanned in countries (e.g.
mode, and it does not support all keyboard country codes. New users should use the Windows mode. Refer to Keyboard Function Relationships, page 7-1 for CTRL+ X Values. Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F (refer to ASCII Conversion Chart (Code Page 1252) on page A-3 for non-reprintable characters), but it does not translate any prefix or suffix information.
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.
RS232 Modifiers RS-232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 38,400.
* 38400 57,600 115,200 RS-232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications which require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity.
7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity Odd * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Even 8 Data, 1 Stop, Parity Odd RS-232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS is still active.
RTS/CTS Off, RTS Inactive: RTS/CTS is turned off so no data flow control is used and RTS is inactive. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host. Character-Based Flow Control, No Timeout: The scanner asserts RTS when it has a character to send, and will wait indefinitely for CTS to be asserted by the host Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit.
Character-Based Flow Control, No Timeout Two-Direction Flow Control Flow Control with Timeout Character-Based Flow Control with Timeout CTS-Based Flow Control, No Timeout RTS On No RTS if CTS is On 2 - 26
RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 165535 milliseconds) by scanning digits from the inside back cover, then scanning Save. Default = 1000.
for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off. ACK/NAK On * ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
3 Input/Output Settings Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = On. * On Off Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.
Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium Low (1600 Hz) * Medium (2750 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal.
Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = 100 Hz. * Razz (100 Hz) * Medium (2000 Hz) High (4200 Hz) LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On. * On Off Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read.
LED flashes are in sync with one another. To change the number of beeps, scan the bar code below and then scan a digit (1-9) bar code and the Save bar code on the inside the back cover of this manual. Default = One. Number of Pulses Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = No Delay.
Trigger Modes Manual/Serial Trigger You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page 9-4). When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released. When in serial mode, the scanner scans until a bar code has been read or until the deactivate command is sent.
Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LEDs are off for ambient conditions until a change occurs in the scanner’s field of view. Then the LEDS turn on automatically to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly.
Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back cover, and Save. Default = 5,000 ms. Hands Free Time-Out Reread Delay This sets the time period before the scanner can read the same bar code a second time. Setting a reread delay protects against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads at POS (point of sale).
User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save. User-Specified Reread Delay Centering Use Centering to narrow the scanner’s field of view to make sure the scanner reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read.
Centering On * Centering Off Left of Centering Window Right of Centering Window 3-9
Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequence symbol programs the scanner to the Universal values, shown below. These are the defaults. Be certain you want to delete or clear all formats before you read the Default Sequence symbol.
Output Sequence Editor Enter Sequence Default Sequence Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 barcodes, but you want the image scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example.
42 start character match for Code 128, 42h = “B” FF termination string for second code 69 code identifier for Code 93 9999 code length that must match for Code 93, 9999 = all lengths 43 start character match for Code 93, 43h = “C” FF termination string for third code To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length.
Output Sequence Editor Enter Sequence Default Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the image scanner will not transmit the output data to the host device. When it’s On/Not Required, the image scanner will attempt to get the output data to conform to an edited sequence, but if it cannot, the image scanner transmits all output data to the host device as is.
beeping (if turned on) for each read. The scanner attempts to find and decode new symbols as long as the trigger is pulled. When this programming selection is turned Off, the scanner will only read the symbol closest to the aiming beam. On * Off No Read With No Read turned On, the scanner sends an “NR” to the host if you pull and release the trigger without reading a code (e.g., bad bar code). If No Read is turned Off, the “NR” will not be sent to the host.
Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. The “Off” bar code below is an example of this type of bar code. Note: If additional menuing is required, Video Reverse must be disabled to read the menu bar codes and then re-enabled after menuing is completed. On VIDREV0REV.
3 - 16
4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string. Prefix and Suffix characters are data characters that can be sent before and after scanned data.
To Add a Prefix or Suffix Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-3). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in Appendix A) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4.
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in Appendix A) for the symbology from which you want to clear the prefix or suffix. Step 3. Scan the 2 digit hex value from the inside the back cover of this manual or scan 9, 9 for all symbologies. Your change is automatically saved.
Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Transmit Alternate Extended ASCII Characters You may need to emulate special keyboard functions, such as up or down arrows, Alt/Make or Alt/Break commands, that are not supported in the Extended ASCII Character table. Refer to Alternate Extended ASCII Characters (page 4-5) for a range of keyboard function keys and corresponding decimal and hex characters.
Alternate Extended ASCII Characters DEC HEX Keyboard Function DEC HEX Keyboard Function 128 80 up arrow ↑ 152 98 F9 129 81 down arrow ↓ 153 99 F10 130 82 right arrow → 154 9A F11 131 83 left arrow ← 155 9B F12 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 Insert Delete Home End Page Up Page Down Right ALT Right CTRL Reserved Reserved Numeric Keypad Enter Numeric Keypad / F1 F2 F3 F4 F5 F6 F7 F8 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170
Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 7-2. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.
Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of steps in 5 millisecond increments and the Save bar code using the inside the back cover of this manual. Prefix Scanned Data 1 2 3 4 Suffix 5 Intercharacter Delay Intercharacter Delay To remove this delay, scan the Intercharacter Delay bar code, then set the number of steps to 0.
To remove this delay, scan the Delay Length bar code, and set the number of steps to 0. Scan the Save bar code using the inside the back cover of this manual. Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each control character in the message string. Scan the Interfunction Delay bar code below, then scan the number of steps in 5 millisecond increments and the Save bar code using the inside the back cover of this manual.
To remove this delay, scan the Intermessage Delay bar code, then set the number of steps to 0. Scan the Save bar code using the inside the back cover of this manual.
4 - 10
5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
Step 3. Terminal Type Refer to the Supported Terminals Chart (page 5-4) and locate the Terminal ID number for your PC. Scan three numeric bar codes on the inside back cover to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge. Note: The wildcard for all terminal types is 099. Step 4. Code I.D. In Appendix A find the symbology to which you want to apply the data format.
data length for the specific data format that you want to delete. All other formats remain unaffected. • Save from the inside the back cover of this manual This exits, saving any Data Format changes. • Discard from the inside the back cover of this manual This exits without saving any Data Format changes.
Interface / Terminal ID Table Interface USB Serial Keyboard PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) PS2 compatibles AT compatibles Terminal ID 124 125 134 130 131 128 129 000 000 051 003 002 Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your input data string.
F2 Example: Send a number of characters Send the first 10 characters from the bar code above, followed by a carriage return. Command string: F2100D F2 is the “Send a number of characters” command 10 is the number of characters to send 0D is the hex value for a CR The data is output as: 1234567890 F2 and F1 Example: Split characters into 2 lines Send the first 10 characters from the bar code above, followed by a carriage return, followed by the rest of the characters.
44 is the hex value for a 'D” 0D is the hex value for a CR The data is output as: 1234567890ABC Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the numeric value (00-99) for the number of characters that will not be sent at the end of the message.
Insert bar code length B4 Insert the bar code’s length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeroes. B3 and B4 Example: Insert the symbology name and length Send the symbology name and length before the bar code data from the bar code above. Break up these insertions with spaces. End with a carriage return.
03 is the number of characters to move the cursor F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 4567890ABCDEFGHIJ Move the cursor backward a number of characters F6 Move the cursor back “nn” characters from current cursor position. Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back. Move the cursor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7.
Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for the CP1252 character. Refer to the ASCII Conversion Chart (Code Page 1252), page A-3 for decimal, hex and character codes. Search forward for a string B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string.
Search forward for a non-matching character E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for the CP1252 character. Refer to the ASCII Conversion Chart (Code Page 1252), page A-3 for decimal, hex and character codes.
FB Example: Remove spaces in bar code data This example shows a bar code that has spaces in the data. You may want to remove the spaces before sending the data.
F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 1234 5678 ABC Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for the CP1252 character.
If this bar code is read: the data is output as: 1234AB Check for non-numeric character ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the character is numeric. ED Example: Only output the data if the bar code begins with a letter If you want only data from bar codes that begin with a letter, you can use ED to check for the letter.
Data Format Editor Enter Data Format * Default Data Format Clear One Data Format Clear All Data Formats Save Discard Data Formatter When Data Formatter is turned off, the bar code data is output to the host as read (including prefixes and suffixes). Choose one of the following options.
Default = Data Formatter On. * Data Formatter On, but Not Required Data Formatter Off When Data Formatter is required, all input data must conform to an edited format or the scanner does not transmit the input data to the host device.
5 - 16
6 Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults.
All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. All Symbologies On All Symbologies Off Message Length You are able to set the valid reading length of some of the bar code symbologies.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09 Max. length = 20 EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15 Max. length = 15 For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of the symbology, then scan the digit value of the message length and Save bar codes on the inside the back cover of this manual.
Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16 check characters. Default = No Check Character. No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. Character Start Stop Start Stop Codabar A12D D34A Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion.
Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Code 39 < Default All Code 39 Settings > Code 39 *On Off Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-48.
are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 39 bar code that starts with a character other than a space. Default = Off. On *Off Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. Default = Off.
Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.
ASCII Conversion Chart (Code Page 1252), page A-3, and scan the value and the Save bar code from the inside the back cover of this manual. The data characters should then appear properly. Code 39 Code Page Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 * On Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80.
Code 93 < Default All Code 93 Settings > Code 93 * On Off Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Code Page Code pages define the mapping of character codes to characters.
select the code page with which the bar codes were created from the chart, ASCII Conversion Chart (Code Page 1252), page A-3, and scan the value and the Save bar code from the inside the back cover of this manual. The data characters should then appear properly.
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial * On Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA On Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Matrix 2 of 5 Matrix 2 of 5 On * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Code 11 Code 11 On * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 Code 128 * On Off ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner.
space-efficient design, 3) a variation of Code 128 that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off. On * Off Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Code 128 Code Page Code 128 Function Code Transmit By default, Code 128 function codes are not transmitted with Code 128 bar code data. However, if you wish to transmit Code 128 function codes with the bar code data, scan the Function Codes On bar code, below.
Telepen On * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output.
Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60.
UPC A UPC A * On Off UPC A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
UPC A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data. Default = Off for both 2 Digit and 5 Digit Addenda.
UPC A Addenda Required When Addenda Required is set to on, the scanner will only read UPC A bar codes that have addenda. Default = Not Required. Required * Not Required UPC A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On.
UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. Default = On.
UPC E UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number system, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1).
UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. On * Off UPC E0 and UPC E1 Addenda Required When Addenda Required is set to on, the scanner will only read UPC E bar codes that have addenda. Default = Not Required.
UPC E0 and UPC E1 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
UPC E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On Off UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data. Default = Off for both 2 Digit and 5 Digit Addenda.
EAN/JAN 13 EAN/JAN 13 * On Off EAN/JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 Addenda Required When Addenda Required is set to on, the scanner will only read EAN/JAN 13 bar codes that have addenda. Default = Not Required.
EAN/JAN 13 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code on page 6-27. ISBN Translate This selection causes EAN-13 Bookland symbols to be translated into their equivalent ISBN number format. Default = Off.
EAN/JAN 8 * On Off Off EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda * 5 Digit Addenda Off EAN/JAN 8 Addenda Required When Addenda Required is set to on, the scanner will only read EAN/JAN 8 bar codes that have addenda. Default = Not Required.
EAN/JAN 8 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Off MSI MSI On * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate and Transmit, the scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data. When Check Character is set to Validate, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character, but will not transmit the check character with the scanned data.
Plessey Code On * Off Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
GS1 DataBar Omnidirectional * On Off GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited * On Off GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > 6 - 40
GS1 DataBar Expanded * On Off GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
China Post Code On * Off China Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Korea Post Code Korea Post Code On * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Codablock F Codablock F On * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Code 49 Code 49 On * Off Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81.
Trioptic Code Trioptic Code is used for labeling magnetic storage media. On Off GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1Composites. If GS1-128 Emulation is selected, the AIM Symbology Identifier will be reported as “]C1”.
Label Code The standard Label Code is used in library situations. Default = Off.
6 - 48
7 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to Windows Mode Control + X Mode On (page 2-20) to enable Control + ASCII mode.
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM AT/XT and PS/2 Compatibles, WYSE PC/AT Supported Keys Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Tab Reserved Tab Delete CR/Enter Insert Escape F11 Home Print Back Space Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Supported Interface Keys ASCII NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US DEL HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F Apple Mac/iMac Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make TAB APPLE break TAB Del RETURN Ins Help ESC F11 Home Prnt Scrn BACKSPACE LSHIFT TAB F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 BACKSPACE 7-3
7-4
8 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts (page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled. Add Code I.D.
change programmed parameters, and create and print programming bar codes. Using EZConfig-Scanning, you can even save/open the programming parameters for a scanner. This saved file can be e-mailed or, if required, you can create a single bar code that contains all the customized programming parameters and mail or fax that bar code to any location. Users in other locations can scan the bar code to load in the customized programming.
5. Follow the security directions as prompted on the screen and click on Download. 6. When prompted, select Save, and save the file to your desktop. 7. Double click on the EZConfig-Scanning zip file. 8. Double click on the EZConfig-Scanning Setup.exe file. Select Extract All. 9. Go to the EZConfig-Scanning folder that has been created on your desktop and double click on the EZConfig-Scanning Setup.exe file. 10. Follow the screen prompts to install the EZConfig-Scanning program. 11.
8-4
9 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual. The device must be set to an RS-232 interface (see page 2-2). The following commands can be sent via a PC com port using terminal emulation software.
Query Commands Several special characters can be used to query the device about its settings. ^ ? * What is the default value for the setting(s). What is the device’s current value for the setting(s). What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a continuous range of values. A pipe (|) separates items in a list of non-continuous values.
Examples of Query Commands In the following examples, a bracketed notation [ ] depicts a non-displayable response. Example: Enter: Response: Example #1:What is the range of possible values for Codabar Coding Enable? cbrena*. CBRENA0-1[ACK] This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on). Example: Enter: Response: Example #2: What is the default value for Codabar Coding Enable? cbrena^.
Trigger Commands You can activate and deactivate the scanner with serial trigger commands. First, the scanner must be put in Manual/Serial Trigger Mode either by scanning the Manual/Serial Trigger Mode bar code (page 3-5), or by sending the Manual/ Serial Menu Command (page 9-13).
Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Product Default Settings Setting Custom Defaults Set Custom Defaults MNUCDF 1-5 Resetting the Custom Defaults Activate Custom Defaults DEFALT 1-5 Keyboard Wedge: IBM PC AT and Compatibles with CR suffix PAP_AT 2-1 Laptop Direct Connect PAPLTD 2-1 RS232 Serial Port PAP232 2-2 IBM Port 5B Interface PAPP5B 2-2 IBM Port 9B HHBCR-1 Interface PAP9B1 2-2 IBM Port 17 Interface PAPP17 2-2
Selection USB Serial Commands Plug and Play Codes: Program Keyboard Country 9-6 Setting * Indicates default Serial Command # Indicates a numeric entry Page USB Serial Emulation PAP130 2-5 CTS/RTS Emulation On USBCTS1 2-6 *CTS/RTS Emulation Off USBCTS0 2-6 ACK/NAK Mode On USBACK1 2-6 *ACK/NAK Mode Off USBACK0 2-6 Honeywell Bioptic Aux Port PAPBIO 2-6 Datalogic Magellan Bioptic Aux Port PAPMAG 2-7 Wincor Mode A PAPWMA 2-7 *U.S.A.
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Czech (Programmers) KBDCTY40 2-10 Czech (QWERTY) KBDCTY39 2-10 Czech (QWERTZ) KBDCTY38 2-10 Denmark KBDCTY8 2-10 Dutch (Netherlands) KBDCTY11 2-10 Estonia KBDCTY41 2-10 Faroese KBDCTY83 2-10 Finland KBDCTY2 2-10 France KBDCTY3 2-11 Gaelic KBDCTY84 2-11 Germany KBDCTY4 2-11 Greek KBDCTY17 2-11 Greek (220 Latin) KBDCTY64 2-11 Greek (220) KBDCTY61 2-11 Greek (319 Latin) KBDCTY6
Selection 9-8 Setting Serial Command Page * Indicates default # Indicates a numeric entry Latvia KBDCTY42 2-13 Latvia (QWERTY) KBDCTY43 2-13 Lithuania KBDCTY44 2-13 Lithuania (IBM) KBDCTY45 2-13 Macedonia KBDCTY34 2-14 Malta KBDCTY74 2-14 Mongolian (Cyrillic) KBDCTY86 2-14 Norway KBDCTY9 2-14 Poland KBDCTY20 2-14 Polish (214) KBDCTY57 2-14 Polish (Programmers) KBDCTY58 2-14 Portugal KBDCTY13 2-14 Romania KBDCTY25 2-14 Russia KBDCTY26 2-15 Russian (MS) KBDCTY
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Turkey Q KBDCTY24 2-17 Ukrainian KBDCTY76 2-17 United Kingdom KBDCTY7 2-17 United Stated (Dvorak right) KBDCTY89 2-17 United States (Dvorak left) KBDCTY88 2-17 United States (Dvorak) KBDCTY87 2-17 United States (International) KBDCTY30 2-17 Uzbek (Cyrillic) KBDCTY77 2-17 Vietnam KBDCTY95 2-17 ALT Mode *Off KBDSTY0 2-18 4 Characters KBDALT0 2-18 Keyboard Style *Regular KBDALT7 2-18
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page *Numeric Keypad Off KBDNPS0 2-21 Numeric Keypad On KBDNPS1 2-21 *Auto Direct Conn. Off KBDADC0 2-21 Auto Direct Conn.
Selection RS-232 Handshaking Scanner-Bioptic Packet Mode Setting Serial Command Page * Indicates default # Indicates a numeric entry 8 Data, 1 Stop, Parity Odd 232WRD8 2-24 *RTS/CTS Off 232CTS0 2-25 RTS/CTS Off, RTS Inactive 232CTS10 2-25 Flow Control, No Timeout 232CTS1 2-25 Character-Based Flow Control, No Timeout 232CTS7 2-26 Two-Direction Flow Control 232CTS2 2-26 Flow Control with Timeout 232CTS3 2-26 Character-Based Flow Control with Timeout 232CTS4 2-26 CTS-Based Flow
Selection Beeper Volume - Good Read Beeper Pitch - Good Read (Frequency) Setting * Indicates default Serial Command # Indicates a numeric entry Page Off BEPLVL0 3-1 Low BEPLVL1 3-1 Medium BEPLVL2 3-1 *High BEPLVL3 3-1 Low (1600 Hz) BEPFQ11600 3-2 *Medium (2750 Hz) BEPFQ12750 3-2 High (4200 Hz) BEPFQ14200 3-2 Beeper Duration Good Read *Normal Beep BEPBIP0 3-2 Short Beep BEPBIP1 3-2 Beeper Pitch - Error *Razz (100 Hz) BEPFQ2100 3-3 *Medium (2000 Hz) BEPFQ22000 3-3 High
Selection Trigger Mode Setting * Indicates default Serial Command # Indicates a numeric entry Page *Manual/Serial Trigger TRGMOD0 3-5 Read Time-Out (0 300,000 ms) *30,000 TRGSTO#### 3-5 Automatic Trigger TRGMOD1 3-5 Presentation Mode TRGMOD3 3-6 Continuous Illumination On ILLAON1 3-6 *Continuous Illumination Off ILLAON0 3-6 Hands Free Time-Out (0-300,000 seconds) *5000 TRGPTO#### ## 3-7 Short (500 ms) DLYRRD500 3-7 *Medium (750 ms) DLYRRD750 3-7 Long (1000 ms) DLYRRD1000 3-
Selection No Read Setting * Indicates default Serial Command # Indicates a numeric entry Page On SHWNRD1 3-14 *Off SHWNRD0 3-14 On VIDREV1 3-14 *Off VIDREV0 3-14 Add CR Suffix to All Symbologies VSUFCR 4-3 Prefix Add Prefix PREBK2## 4-3 Clear One Prefix PRECL2 4-3 Video Reverse Prefix/Suffix Selections Clear All Prefixes PRECA2 4-3 Add Suffix SUFBK2## 4-4 Clear One Suffix SUFCL2 4-4 Clear All Suffixes SUFCA2 4-4 Transmit Alternative Extended ASCII Characters Transmi
Selection Data Formatter Setting Serial Command * Indicates default # Indicates a numeric entry Page Off DFM_EN0 5-15 *On, but Not Required DFM_EN1 5-15 On, Required DFM_EN2 5-15 Symbologies All Symbologies All Symbologies Off ALLENA0 6-2 All Symbologies On ALLENA1 6-2 Codabar Default All Codabar Settings CBRDFT 6-3 Codabar Off CBRENA0 6-3 *On CBRENA1 6-3 Codabar Start/Stop Char. *Don’t Transmit CBRSSX0 6-4 Transmit CBRSSX1 6-4 Codabar Check Char. *No Check Char.
Selection Code 39 Message Length Code 39 Append Setting * Indicates default Serial Command # Indicates a numeric entry Page Minimum (0 - 48) *0 C39MIN## 6-8 Maximum (0 - 48) *48 C39MAX## 6-8 *Off C39APP0 6-9 On C39APP1 6-9 Code 32 Pharmaceutical (PARAF) *Off C39B320 6-9 On C39B321 6-9 Code 39 Full ASCII *Off C39ASC0 6-10 On C39ASC1 6-10 Default All Interleaved 2 of 5 Settings I25DFT 6-11 Off I25ENA0 6-11 *On I25ENA1 6-11 *No Check Char.
Selection Straight 2 of 5 IATA Straight 2 of 5 IATA Setting Serial Command Page * Indicates default # Indicates a numeric entry Default All Straight 2 of 5 IATA Settings A25DFT 6-16 *Off A25ENA0 6-16 On A25ENA1 6-16 Straight 2 of 5 IATA Message Length Minimum (1 - 48) *4 A25MIN## 6-16 Maximum (1 - 48) *48 A25MAX## 6-16 Matrix 2 of 5 Default All Matrix 2 of 5 Settings X25DFT 6-17 Matrix 2 of 5 *Off X25ENA0 6-17 On X25ENA1 6-17 Matrix 2 of 5 Message Length Minimum (1 - 80)
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry Code 128 Function Code Transmit *Off 128FNX0 6-21 On 128FNX1 6-21 Telepen Default All Telepen Settings TELDFT 6-22 Telepen Telepen Output *Off TELENA0 6-22 On TELENA1 6-22 *AIM Telepen Output TELOLD0 6-22 Original Telepen Output TELOLD1 6-22 Telepen Message Length Minimum (1 - 60) *1 TELMIN## 6-23 Maximum (1 - 60) *60 TELMAX## 6-23 UPC A Default All UPC A Settings UPADFT 6-24 UPC A
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry UPC E Default All UPC E Settings UPEDFT 6-28 UPC E0 Off UPEEN00 6-28 *On UPEEN01 6-28 *Off UPEEN10 6-28 On UPEEN11 6-28 *Off UPEEXP0 6-29 On UPEEXP1 6-29 UPC E1 UPC E Expand UPC E Check Digit Off UPECKX0 6-30 *On UPECKX1 6-30 UPC E Number System Off UPENSX0 6-31 *On UPENSX1 6-31 UPC E 2 Digit Addenda *Off UPEAD20 6-31 On UPEAD21 6-31 UPC E 5 Digit Addenda *Off UPEAD50 6-
Selection Setting Serial Command Page * Indicates default # Indicates a numeric entry EAN/JAN 13 Addenda Required *Not Required E13ARQ0 6-33 Required E13ARQ1 6-33 EAN/JAN 13 Addenda Separator Off E13ADS0 6-34 *On E13ADS1 6-34 ISBN Translate *Off E13ISB0 6-34 On E13ISB1 6-34 Default All EAN/ JAN 8 Settings EA8DFT 6-35 EAN/JAN 8 EAN/JAN 8 Off EA8ENA0 6-35 *On EA8ENA1 6-35 EAN/JAN 8 Check Digit Off EA8CKX0 6-35 *On EA8CKX1 6-35 EAN/JAN 8 2 Digit Addenda *Off EA8AD2
Selection Plessey Code Setting Serial Command Page * Indicates default # Indicates a numeric entry *Off PLSENA0 6-39 On PLSENA1 6-39 Plessey Message Length Minimum (4 - 48) *4 PLSMIN## 6-39 Maximum (4 - 48) *48 PLSMAX## 6-39 GS1 DataBar Omnidirectional Default All GS1 DataBar Omnidirectional Settings RSSDFT 6-40 GS1 DataBar Omnidirectional Off RSSENA0 6-40 *On RSSENA1 6-40 GS1 DataBar Limited Default All GS1 DataBar Limited Settings RSLDFT 6-40 GS1 DataBar Limited Off RS
Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Korea Post Code Msg. Length Minimum (2 - 80) *4 CPCMIN## 6-43 Maximum (2 - 80) *80 CPCMAX## 6-43 Codablock F Default All Codablock F Settings CBFDFT 6-44 Codablock F *Off CBFENA0 6-44 On CBFENA1 6-44 Codablock F Msg.
10 Product Specifications Hyperion 1300g Product Specifications Parameter Specification Mechanical Height 5.9 inches (15 cm) Length 4.4 inches (11.2 cm) Width 3.1 inches (7.9 cm) Weight 5.6 ounces (160 g) Electrical LED source 630 nm visible red LED Input Voltage 4.5-5.
Standard Connector Pinouts Keyboard Wedge 10 Pin RJ41 Modular Plug - connects to the scanner handle 1 2 3 4 5 6 7 8 9 10 Cable shield Cable select Supply ground Terminal data Terminal clock Keyboard clock +5V power Keyboard data Serial Output 10 Pin RJ41 Modular Plug - connects to the scanner handle 1 2 3 4 5 6 7 8 9 10 Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner CTS +5V power RTS USB 10 Pin Modular Plug - connects to the scanner handle 1 2 3 4 5 6 7 8 9 1
Required Safety Label Locations Light Source Item Number, Serial Number and Revision Compliance Label location 10 - 3
10 - 4
11 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center. See Customer Support on page 12-1 for further information. Maintenance Your device provides reliable and efficient operation with a minimum of care.
Replacing the Interface Cable The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in the scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable. Replacing the Interface Cable: 1.
Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the symbols: • Aren’t smeared, rough, scratched, or exhibiting voids. • Aren’t coated with frost or water droplets on the surface. • Are enabled in the scanner or in the decoder to which the scanner connects. Is the bar code displayed but not entered? The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example).
11 - 4
12 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below: Knowledge Base: www.hsmknowledgebase.com Our Knowledge Base provides thousands of immediate solutions. If the Knowledge Base cannot help, our Technical Support Portal (see below) provides an easy way to report your problem or ask your question. Technical Support Portal: www.hsmsupportportal.
ship, HII, at its sole option, will either repair or replace the product without charge, except for return shipping to HII. EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT.
A Appendix A Symbology Charts Note: “ m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. Refer toData Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID and AIM ID.
AIM Symbology EAN-8 with Add-On ID Possible modifiers (m) ]E3 Honeywell ID Hex D 44 y 79 { 7B GS1 GS1 DataBar ]em 0 GS1 DataBar Limited ]em GS1 DataBar Expanded ]em } 7D GS1-128 ]C1 I 49 China Post (Hong Kong 2 of 5) ]X0 Q 51 Interleaved 2 of 5 ]Im e 65 Matrix 2 of 5 ]X0 m 6D NEC 2 of 5 ]X0 Y 59 Straight 2 of 5 IATA ]Rm f 66 Straight 2 of 5 Industrial ]S0 f 66 g 67 2 of 5 MSI ]Mm UPC A-2 0, 1, 3 0, 1, 3 0, 1 0, 1, 2, 3, 8, 9, A, B, C UPC-A ]E0 c 6
Postal Symbologies AIM Symbology ID Possible modifiers (m) Honeywell ID Hex All Symbologies 99 Australian Post ]X0 A 41 British Post ]X0 B 42 Canadian Post ]X0 C 43 China Post ]X0 Q 51 InfoMail ]X0 , 2c Intelligent Mail Bar Code ]X0 M 4D Japanese Post ]X0 J 4A KIX (Netherlands) Post ]X0 K 4B Korea Post ]X0 ? 3F Planet Code ]X0 L 4C Postal-4i ]X0 N 4E Postnet ]X0 P 50 ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Charact
2 02 STX CTRL+ B Bold Caps Lock Txt: [STX] 3 03 ETX CTRL+ C Copy ALT Make Txt: [EXT] 4 04 EOT CTRL+ D Bookmark ALT Break Txt: [EOT] 5 05 ENQ CTRL+ E Center CTRL Make Txt: [ENQ] 6 06 ACK CTRL+ F Find 7 07 BEL CTRL+ G 8 08 BS CTRL+ H History (Apple Make) Txt: [BS] 9 09 HT CTRL+ I Italic Tab Txt: [HT] 10 0A LF CTRL+ J Justify (Apple Break) Txt: [LF] 11 0B VT CTRL+ K hyperlink Tab Txt: [VT] 12 0C FF CTRL+ L list, left align Delete Txt: [FF]
Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters DEC HEX 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F Character ! " # $ % & ' ( ) * + , .
Extended ASCII Characters DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 128 80 € Ç up arrow ↑ 0x48 129 81 ü down arrow ↓ 0x50 130 82 ‚ é right arrow → 0x4B 131 83 ƒ â left arrow ← 0x4D 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 „ … † ‡ ˆ ‰ Š ‹ Œ ä à å ç ê ë è ï î ì Ä Å É æ Æ ô ö ò û
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 ¥ ¦ § ¨ © ª « ¬ Ñ ª º ¿ ⌐ ¬ ½ ¼ ¡ « » ░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛ ┐ └ ┴ ┬ ├ ─ í ╞ ╟ ╚ ╔ ╩ ╦ Print Screen Tab Shift Tab Enter Esc Alt Make Alt Break Control Make Control Break Alt Sequence with 1 Character Ctrl Sequence with 1 Character n/a 0x0F 0x8F 0x
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 Ì Í Î Ï Ð Ñ Ò Ó Ô Õ Ö × Ø Ù Ú Û Ü Ý Þ ß à á â ã ä å æ ç è é ê ë ì í î ï ð ñ ò ╠ ═ ╬ ╧ ╨ ╤ ╥ ╙ ╘ ╒ ╓ ╫ ╪ ┘ ┌ █ ▄ ▌ ▐ ▀ α ß Γ π Σ σ µ τ Φ Θ Ω δ ∞ φ ε ∩ ≡ ± ≥ A-8 CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 Alternate E
Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII 243 244 245 246 247 248 249 250 251 252 253 254 255 ó ô õ ö ÷ ø ù ú û ü ý þ ÿ ≤ ⌠ ⌡ ÷ ≈ ° · · √ ⁿ ² ■ F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF PS2 Scan Code Alternate Extended ISO 2022/ISO 646 Character Replacements Code pages define the mapping of character codes to characters.
United States ISO/IEC 646‐06 0 1 Canada ISO /IEC 646‐121 54 95 Canada ISO /IEC 646‐122 18 96 Japan ISO/IEC 646‐14 28 98 China ISO/IEC 646‐57 92 99 Great Britain (UK) ISO /IEC 646‐04 7 87 France ISO /IEC 646‐69 3 83 Germany ISO/IEC646‐21 4 84 Switzerland ISO /IEC 646‐CH 6 86 Sweden / Finland (extended Annex C) ISO/IEC 646‐11 2 82 Ireland ISO /IEC 646‐207 73 97 Danmark ISO/IEC 646‐08 8 88 Norway ISO/IEC 646‐60 9 94 Italy ISO/IEC 646‐15 5 85 Portugal ISO
64 91 92 93 94 96 123 124 125 126 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E US 0 1 # $ @ [ \ ] ^ ` { | } ~ CA 54 95 # $ à â ç ê î ô é ù è û CA 18 96 # $ à â ç ê É ô é ù è û JP 28 98 # $ @ [ ¥ ] ^ ` { | } ⎯ CN 92 99 # ¥ @ [ \ ] ^ ` { | } ⎯ GB 7 87 £ $ @ [ \ ] ^ ` { | } ˜ FR 3 83 £ $ à ° ç § ^ µ é ù è ¨ DE 4 84 # $ § Ä Ö Ü ^ ` ä ö ü ß CH 6 86 ù $ à é ç ê î ô ä ö ü û
Unicode Key Maps 6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2B 4B 50 55 4C 51 56 2C 2E 2F 30 31 32 33 34 35 36 37 39 3D 3A 3B 3C 3E 3F 38 40 53 4F 54 59 5A 5F 5B 60 5C 61 5D 62 63 64 69 65 6A 66 67 6C 68 5A 5F 5B 60 5C 61 5D 62 63 64 69 65 6A 66 67 6C 68 104 Key U.S.
Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN 13 EAN 8 9 780330 290951 654 3210 5 UPC-E 0 456123 8
Sample Symbols Code 39 BC321 Code 93 123456-9$ Matrix 2 of 5 6543210 Codabar A13579B Straight 2 of 5 Industrial 123456 GS1 DataBar (01)00123456789012
Programming Chart 0 1 2 3 4 5 6 7 8 9
Programming Chart A B C D E F Save Discard Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.
