Dolphin® 9900 Mobile Computer with Windows Mobile® 6.
Disclaimer Honeywell International Inc. (“Honeywell”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Honeywell.
Table of Contents Chapter 1 - Agency Information Label Locations ................................................................................................................... 1-1 Regulatory and Safety Approvals for all Dolphin Terminals ............................................... 1-2 FCC Compliance ................................................................................................................. 1-3 Chapter 2 - Getting Started Using the Dolphin Terminal for the First Time .........
Keyboard Options................................................................................................................ 5-1 Common Buttons ........................................................................................................... 5-1 Keyboard Combinations ................................................................................................ 5-1 Using the Function Keys......................................................................................................
Installing Additional Software .............................................................................................. 7-8 Adding Programs to the Terminal Using ActiveSync ..................................................... 7-8 Adding Programs Directly from the Internet................................................................... 7-9 COM Port Assignment Table ............................................................................................
Mounting the HomeBase ................................................................................................. 10-10 Chapter 11 - Dolphin Mobile Base Overview............................................................................................................................ 11-1 Mobile Base Parts and Functions...................................................................................... 11-2 Powering the Dolphin Terminal .............................................................
1 Agency Information Label Locations Dolphin 9900 mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your Dolphin mobile computer.
Regulatory and Safety Approvals for all Dolphin Terminals Parameter Specification U.S.A. Canada European Community FCC Part 15, Class B ICES-003 EN 55022 (CISPR 22) Class B EN60950:2000 EN60825-1:1994 + A11 + A2 EN55024:1998 The CE Mark on the product indicates that the system has been tested to and conforms with the provisions noted within the 89/336/EEC Electromagnetic Compatibility Directive and the 73/23/ EEC and 93/68/EEC Low Voltage Directive.
FCC Compliance Dolphin terminals comply with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Dolphin RF Terminal—802.11b/g (WLAN), Bluetooth, and/or GSM This device complies with Part 15 of the FCC Rules.
RF, Regulatory, and Safety Agency Approvals—802.11b/g (WLAN), Bluetooth, and/or GSM ParameterM Specification U.S.A. Canada FCC Part 15.247 RSS 210 R&TTE Compliance Statement—802.11b/g (WLAN), Bluetooth, and/or GSM Dolphin RF terminals are in conformity with all essential requirements of the R&TTE Directive (1999/5/ EC).
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.
1-6 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
2 Getting Started Using the Dolphin Terminal for the First Time 1. Unpack the Carton and Verify its Contents (see page 2-1) 2. Install the Main Battery Pack (see page 2-2) 3. Charge the Main and Backup Batteries (see page 2-2) 4. Initialize the Mobile Computer (see page 2-2) 5. Let Autoinstall Run (see page 2-3) 6. Set the Time and Date (see page 2-3) 7. Verify Imaging and Decoding with Demos (see page 2-4) Step 1.
Step 2. Install the Main Battery Pack ! Use only the Li-ion battery packs provided by Hand Held Products. Use of any battery not sold/manufactured by Hand Held Products may damage the terminal and/or the battery, may pose a personal hazard to the user, and will void the warranty. 1. Unpack the Li-ion battery pack. Hold the terminal with the front panel (keyboard) facing down. 2.
2. The terminal initializes and the splash screen displays for a few seconds. The Build numbers indicate the software version. Bootloader Kernel 3. Keyboard 9.XX/9.XX/9.XX/9.XX Initial Program Loader (IPL) The system performs a hard reset. When the display activates again, follow the instructions that appear. Step 5. Align the Screen You are prompted to align the screen by tapping the target five times. Use the stylus provided by Honeywell.
On the Today screen, tap the line that displays the time and date, The Clock Settings screen appears. The time zone defaults to GMT-5 Eastern US; tap the arrow to the right of GMT-5 Eastern US to select another time zone. Set the correct time and date in the remaining fields and tap OK to save. Step 8. Verify Imaging and Decoding with Demos Dolphin terminals come loaded with Demos you can use to verify imaging and decoding.
Today Screen After the Dolphin terminal initializes the first time, you see the Today screen. You can also display the Today screen anytime by tapping Start and then Today. Navigation Bar and Start Menu The Navigation bar is located at the top of the screen that displays the active program and current time. It also provides access to the Start menu, which allows you to open programs and access the system settings.
Pop-Up Menus With pop-up menus, you can quickly choose an action for a selected item. To access a pop-up menu, tap and hold the stylus on the item name of the action you want to perform the action. When the menu appears, lift the stylus, and tap the action you want to perform. Tap anywhere outside the menu to close the menu without performing an action. Selecting Programs To see additional programs loaded on your terminal, tap Start > Programs.
3 Hardware Overview Standard Terminal Configurations Dolphin 9900 Dolphin 9900 • • • • • • • • • • • • • Microsoft Windows Mobile 6.0 Intel XScale PXA27x 624 MHz 256MB RAM X 1GB Flash One of three in-mold, hard-top keyboard options 2400mAh Extended life main battery One of 5100SR/SF/HD or 5300SR/SF/HD image engines WLAN (802.11b/g) radio radio Dolphin® 9900 Mobile Computer User’s Guide–Preliminary • • • • • Microsoft Windows Mobile 6.
Dolphin 9900 Series Peripherals Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal. Dolphin HomeBase™ The Dolphin HomeBase charging and communication cradle supports both RS-232 and USB communications, which enable it to interface with the majority of PC-based enterprise systems. When a terminal is seated in the HomeBase, its main battery pack charges in less than four hours.
Dolphin 9900 Series Accessories Each of the following items is sold separately to enhance your Dolphin 9900 Series terminal’s capabilities. Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away from the body. Dolphin Mobile Charger The Dolphin Mobile Charger is a charging cable that connects the terminal directly to a 12 Volt DC power source, such as a cigarette lighter port inside a vehicle, eliminating the need for a cradle.
Front Panel Features This section describes features on the front panel on the Dolphin 9900.
LEDs The two light emitting diodes (LEDs) located at the top of the LCD display flash and illuminate during resets and scanning/imaging. Both can be programmed by various software applications. Scan LED - Located in the upper right corner, this LED lights red when you press the SCAN key. Decode LED - Located in the upper left corner, this LED lights green when a scanned bar code is successfully decoded. Touch Panel Display Dolphin terminals feature a color 3.
Back Panel Features The following graphic describes features on the back panel of the Dolphin 9900.
Image Engine Window Dolphin terminals have an optional image engine that reads and decodes linear, stacked linear (e.g., PDF417), and 2D matrix bar code symbologies. With the latest CMOS-based technology, the engine works like a digital camera and enables digital image capture, signature capture, and reading of OCR characters. Digital images taken with Dolphin terminals have a maximum image size of 640 x 480 pixels and may have up to a 256 grayscale image definition.
Side Panel Features The following graphic shows the left, side panel: IrDA Port Access Door to SD Memory Audio Jack (2.5mm) IrDA Port The IrDA port communicates with IrDA-enabled devices such as PCs, printers, modems, or other Dolphin terminals. The maximum data transfer speed is 115kbps. SD Memory The access door provides user access to the industry-standard SD memory interface. You can open the access door to insert SD memory cards to expand the terminal’s memory capacity.
Bottom Panel Features Hand Strap Clip I/O Connector Note: Signals referenced are for a DTE I/O Connector The I/O connector powers the terminal, charges the main battery, and facilitates communication. All Dolphin peripherals are designed to work exclusively with this connector. The I/O connector supports RS-232 or USB. For RS-232, the maximum communication speed is 115 Kbps with seven baud rate settings. For USB, the communication speed is up to 12 Mbps.
ActiveSync Communication To synchronize, ActiveSync 4.5 or higher must be installed and configured for the appropriate communication type on the host workstation and the Dolphin terminal. Dolphin terminals ship with ActiveSync already installed. Therefore, if ActiveSync is already installed on the host workstation, you just need to connect the Dolphin terminal to the host workstation (via Dolphin peripheral) to initiate communication. If ActiveSync 4.
Software Requirements for Communication To sync successfully, ActiveSync must be configured for same communication type on both the host workstation and the Dolphin terminal. ActiveSync must be setup on your workstation before you initiate synchronization from the terminal for the first time. Setting Up the Host Workstation Verify that ActiveSync is configured to use the appropriate communication type by clicking File > Connection Settings. For RS-232 communication, connect to COM1.
The Mobile Device folder opens in Windows Explorer. The Dolphin terminal is now treated as a mass storage device, and transferring files is as simple as dragging and dropping or copying and pasting as you would for moving files between folders on your hard drive.
Using the Touch Panel Honeywell defines proper use of the terminal touch panel as using a screen protector and proper stylus. Screen protectors maintain the ongoing integrity (i.e., prevent scratching) of the touch panel, which is why their use is recommended for applications that require a high to medium level of interface with the touch panel, such as signature capture for proof of delivery. Honeywell continues to advocate the use of screen protectors on all Dolphin devices.
3. Apply the touch panel protector to your device by sliding the enclosed squeegee across the surface as you peel away the backing. 4. Use the squeegee as necessary to smooth out any air pockets or bumps.
Batteries Dolphin terminals feature intelligent battery technology. There are two types of battery power: the main battery pack installed in the back panel and the backup battery located inside the terminal. They are designed to work together to prevent data loss when the terminal is in use over long periods. Both batteries must be completely charged before using a Dolphin terminal for the first time! Main Battery Pack ! Use only the Li-ion battery packs provided by Hand Held Products.
• Don’t short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury. • Excessive discharge damages a battery. Recharge the battery when your terminal indicates low battery power. • If you observe that the battery is physically damaged in some way, please send it to Hand Held Products or an authorized Hand Held Products service center for inspection. • Although your battery can be recharged many times, it will eventually be depleted.
Internal Backup Battery Located inside the terminal, the backup battery is a 3.6 Volt nickel metal hydride (NiMH) battery. The internal backup battery prevents the terminal from being reset if you need to remove and replace the main battery pack. It retains RAM data and allows the real-time clock to remain operational for up to 30 minutes when the main battery pack is removed.
Managing Battery Power Data and files saved on Dolphin terminals may be stored in RAM memory, which does not persist through a hard reset. Therefore, to help prevent data loss, maintain a continuous power supply to the terminal. Letting the backup battery become fully discharged causes the terminal to lose all data in RAM. Therefore, you should keep a charged battery pack in the Dolphin at all times.
2. Drill-down to HKEY_LOCAL_MACHINE > System > CurrentControlSet > Control > Power. 3. Tap the Value Name to change the Value Data. You can reset the Value Data from 0 (no warning) to 99 (would nearly always warn). 4. Tap OK to save changes. For more information about the RegEdit Power Tool, refer to the Dolphin Power Tools User’s Guide available for download at www.handheld.com. Checking Battery Power Tap Start > Settings > System tab > Power.
Resetting the Terminal There are two types of system resets: a soft and a hard reset. Soft Reset (Warm Boot) A soft reset re-boots the device without losing RAM data. You would perform a soft reset when • the terminal fails to respond. • after installing some software applications. • after making changes to certain system settings, such as network cards. 1. Press and hold the CTRL + SFT keys for approximately five seconds. 2.
4 Using Scan Image Engine Overview The Dolphin terminal houses a compact image engine that instantly reads popular 1D and 2D bar codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The image engine can also capture digital images, such as signatures and pictures of damaged inventory.
Bar Code Symbologies Supported Symbology type Symbologies Supported 1D Symbologies Codabar Code 3 of 9 Code 11 Code 32 Pharmaceutical (PARAF) Code 93 Code 128 EAN with Add-On and EAN with Extended Coupon Code EAN-13 GS1 DataBar Interleaved 2 or 5 Matrix 2 of 5 Plessey PosiCode Straight 2 of 5 IATA Straight 2 of 5 Industrial Telepen Trioptic Code UCC/EAN-128 UPC and UPC-A 2D Symbologies Aztec Code 16K Composite Data Matrix GS1 DataBar MaxiCode OCR PDF417 QR Code Composite Codes Aztec Mesa Codablock F
Decoding The terminal supports two types of image decoding for use in various bar code reading and imaging applications: full-area imaging and Advanced Linear Decoding (ALD). Full-Area Imaging Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR, signature capture, and picture taking. When reading all bar code types using full-area imaging, a positive read can be obtained from many positions; see Scanning Position Options on page 4-4.
Scanning Position Options The aiming beams are smaller when the terminal is held closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit whereas symbologies with larger bars or elements (mil size) should be read farther from the unit.
Capturing Images The image-capture process is an intuitive, split-second operation for experienced users. By following the basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to adapt it to different application environments. Image Preview When the imaging process is initiated, Dolphin touch screens display a preview of the object. This is a live video image of what the imager is currently viewing.
5300 High-Vis Aiming Pattern If your Dolphin terminal is configured with the 5300 imager, you can enable the aiming pattern for imaging in the Imaging Demo. 1. Tap Start > Demos > Imaging Demo > Setup menu > Aimer. 2. The aiming pattern is now enabled for imaging. Uploading Images Image files can be uploaded to a host PC via Microsoft ActiveSync and a Dolphin communication peripheral or your wireless radio connection.
5 Using Dolphin Keyboards Keyboard Options There are two keyboards available in the Dolphin 9900 Series: 43-key Alpha/Numeric Keyboard 56-key Full Alpha/Numeric Keyboard SCAN SCAN ESC ESC TAB TAB VOL PG NUM SFT ENT SEND A E 4 I 7 M B 2 F 5 J 8 N 0 F1 Q K 9 ‘ O S F6 V START Z , _ H = L END INS 1 2 3 SP 4 5 6 BKSP 7 8 9 # 0 DEL + P + F1 ; A _ F4 T F7 # - D F3 R Y G 6 F2 F5 U C 3 ENT SEND END 1 VOL PG B W X INS DEL SP BKSP _
Using the Function Keys Name Key Backlight Turns the keyboard backlight on and off. Backspac e (BKSP) BKSP Delete (DEL) DEL Enter (ENT) ENT Escape (ESC) ESC Power Key SCAN Key Space (SP) Tab Function Moves the cursor back one space each time the key is pressed. If you are typing text, it deletes the previous character each time it is pressed. Deletes the next character forward each time the key is pressed. This key appears on the 56-key keyboard only. 43-key keyboard= Red + BKSP.
Name Blue and Red Key Function The blue and red keys are used in combination with other keys to type special characters and perform system functions. Each key modifies only the next key pressed. The overlay of each keyboard is color-coded to indicate the character typed or function performed when specific keys are pressed immediately after the blue or red modifier key.
Using the Navigation Keys Located in the center of each keyboard for easy access with either hand, the navigation keys navigate the cursor through application screens. Button VOL PG VOL PG Function & & Moves the cursor up one row or line. OR Moves the cursor down one row or line. Raises the volume. OR Lowers the volume. Moves the cursor one character to the right. Moves the cursor one character to the left. Note: Additional functionality varies according to the application in use.
4. In the bottom half of the window, double-tap the StickyCtrlAlt key and change the Value Data from “0” to “1.” 5. Tap OK, then OK in the upper right corner to save the change to the registry. 6. Press the CTRL key combination with other keys to verify that you do not need to hold them down while you press the next key. For an example of CTRL key combinations, see General Windows Keyboard Shortcuts on page 5-14.
43-Key Alpha/Numeric Keyboard SCAN key Power key Escape key SCAN Backlight key (+ Blue to suspend/resume NUM Lock key Navigation keys ESC Tab key TAB Enter key VOL PG NUM ENT SEND NUM Lock Pad NUM Lock Indicators END A 1 B 2 E 4 I 7 M C 3 F 5 G 6 H J 8 K 9 L N 0 ‘ O F1 Q F2 U S F6 Y = + P F4 T F7 # V START _ F3 R F5 , - D Space key F8 W X INS DEL SP BKSP Z CTRL Backspace key (+ Red to delete) SFT CTRL, Blue, Red, SFT Modifier keys Number
43-Key Blue Key Combinations Key Combination Blue key + NUM Blue key + ENT NUM ENT Function/Special Character Send (a phone call) End (a phone call) Blue key + D - Blue key + H _ Blue key + L = Blue key + P + Blue key + Q ; Blue key + R : Blue key + S “ Blue key + T / Blue key + U @ Blue key + V * Blue key + W # Blue key + X \ Blue key + Y Start menu 43-Key Red Key Combinations Key Combination Function/Special Character Red key + SFT Toggles on Caps Lock Red key + Q F1 R
Key Combination Function/Special Character Red key + SP Insert Red key + BKSP Delete 5-8 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
43-Key Num Lock Key Combinations????????? The 43-key keyboard defaults to alpha mode. To switch to num lock mode, press the NUM key once. In Num Lock mode, when you press a letter key, you type the number indicated by the num lock indicators over the key. Key/Key Combination Function/Special Character NUM Press the NUM key only once to switch to num lock mode.
56-Key Full Alpha/Numeric Keyboard SCAN key Navigation keys Power key SCAN ESC Escape key Tab key Backlight key TAB Shift key Insert key Enter key VOL PG SFT ENT SEND END INS 1 2 3 SP 4 5 6 BKSP 7 8 Space key Backspace key Delete key 9 # 0 DEL + F1 ; A _ B C G L K F8 F16 F21 V F14 F18 F15 O F19 S F23 W F10 J N R F22 U F9 F13 F17 Q P E I M F5 F4 D H F12 F11 @ F3 F7 F6 F _ F2 F20 T F24 X F25 Y START CTRL Z CTRL, Blue, and Red Modi
Key Combination Function/Special Character Blue key + K @ Blue key + L / Blue key + P - Blue key + Q \ Blue key + U Start menu 56-Key Red Key Combinations Key Combination Function/Special Character Red key + SFT Toggles on Caps Lock Red key + A F1 Red key + B F2 Red key + C F3 Red key + D F4 Red key + E F5 Red key + F F6 Red key + G F7 Red key + H F8 Red key + I F9 Red key + J F10 Red key + K F11 Red key + L F12 Red key + M F13 Red key + N F14 Red key + O F15 Re
Key Combination Function/Special Character Red key + V F22 Red key + W F23 Red key + X F24 5 - 12 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
56-Key SFT Key Combinations??????? Key Combination Function/Special Character SFT + 1 ! SFT + 2 @ SFT + 3 # SFT + 4 $ SFT + 5 % SFT + 6 ^ SFT + 7 & SFT + 8 * SFT + 9 ( SFT + 0 ) SFT +.
General Windows Keyboard Shortcuts Press these keys, To… CTRL + C Copy CTRL + X Cut CTRL + V Paste CTRL + Z Undo DELETE Delete CTRL + Right Arrow Move the insertion point to the beginning of the next word. CTRL + Left Arrow Move the insertion point to the beginning of the previous word. CTRL + Down Arrow Move the insertion point to the beginning of the next paragraph. CTRL + Up Arrow Move the insertion point to the beginning of the previous paragraph.
6 Settings Overview Customized settings are available from the Start menu. Tap Start > Settings and settings screen opens. Settings consists of three tabs: Personal Tab System Tab Connections Tab Tab Description See Page Personal Customize buttons, set SIP options, and adjust headset settings. Personal Tab, page 6-2 System Adjust system settings. System Tab, page 6-7 Connections Establish network connections settings.
Personal Tab To access the Personal tab, tap Start > Settings. The screen opens to the Personal tab. Button Name Description See Buttons Customize keyboard buttons to perform functions. Buttons on page 6-3. Input Customize the SIP. Input Panel Options on page 6-4. Lock Password protect the terminal to limit access to your device. Menus Customize the Start and New menus. Owner Information Enter your contact information. Phone Opens the settings window for the GSM phone, if installed.
Buttons Buttons programs keyboard buttons to launch applications or execute commands. The default button assignments that appear on the Buttons window are inactive until you enable the HotKeys Power Tool. To Enable HotKeys 1. Tap Start > Power Tools. 2. Tap the HotKeys icon once . HotKeys activates the button assignments in Buttons. 3. Verify the assignment by tapping the button on the keyboard.
Command Description Nothing happens when the button is pressed. Performs the same function as tapping OK on the screen. Scrolls down in the open application. Scrolls left in the open application. Scrolls right in the open application. Scrolls up in the open application. Opens the Start menu. Opens the Today screen.
Menus–Modifying the Start Menu You can add existing programs you use often, such as File Explorer, to the Start menu. You are not installing or moving the program itself, you are simply creating a shortcut to the program from the Start menu. You can modify the Start menu, • Using Menus (page 6-5), • Using File Explorer (page 6-5), or • Using ActiveSync on the Desktop (page 6-6) Using Menus 1. Tap Start > Settings > Personal tab > Menus. 2. Select the program you want to add and tap OK to save. 3.
Using ActiveSync on the Desktop You can use the Explore feature of ActiveSync on your desktop computer to navigate through the files on your Dolphin terminal. The process is essentially the same, except that you are using Windows Explorer on the PC to create and paste the shortcut. 1. Tap ActiveSync > Explore. 2. Navigate to the program. 3. Right-click on the program and select Create Shortcut. 4. Select the shortcut, right-click, and select Cut. 5.
System Tab The System tab enables you to verify and sometimes alter system parameters. To access the System tab, tap Start > Settings > System tab. Tap the appropriate icon to open that system setting. About The About system setting displays specific information about what is loaded on the terminal. It contains three tabs: Version, Device ID, and Copyrights. Version Tab Displays the information about the software, operating system, and processor of the terminal.
Backlight The Backlight Setting has two tabs: Battery and External; the options on each tab are the same. The Battery tab determines display backlight settings when the terminal is running on battery power. The External tab determines display backlight settings when the terminal is powered by an external source, such as a Honeywell cable. Field Description Turn off backlight Select how many minutes you want to elapse before the backlight automatically turns off.
Memory There are two kinds of memory: Main Board/IPSM 256MB RAM X 1GB Flash Secure Digital (SD) Card Each terminal has an SD memory interface for additional application and data storage. You can order memory cards to increase memory. Each terminal contains an access door on the side panel that makes the SD memory interface user-accessible; see Access Door to SD Memory on page 3-8.
Storage Card Tab This tab displays the current capacity and usage statistics of the selected memory type; IPSM or Storage Card. Select the memory type from the drop-down list. IPSM is selected by default. Total storage card memory The total MB of memory capacity of the selected memory. In use The MB currently being used. Free The MB that is still available for use. IPSM—Short for Internal Persistent Storage Manager, this is the 14MB of on-board Flash memory that is non-volatile.
Power Battery Tab Displays the remaining charge of both the main and backup batteries. For more information about the terminal’s batteries, see Batteries on page 3-15. Advanced Tab Determines power time-outs for battery and external power. When the device is “turned off,” that means that it goes into Suspend Mode (see page 3-20). Regional Settings Regional Settings enables you to customize the appearance and formatting to your geographic region.
Remove Programs The Remove Programs settings enables you to remove programs installed on the terminal. Use this setting to troubleshoot when you receive messages that the device is low on of memory. The programs removed here are removed from RAM memory. Any program (usually *.cab or *.dll files) stored in the Autoinstall folder (My Device > IPSM > AutoInstall) will re-install after the next hard reset; see Hard Reset (Cold Boot) on page 3-20. 1. Tap the Remove Programs icon. 2.
Screen Note: By default, dynamic screen rotation (i.e., the ability to switch between landscape and portrait orientation) is disabled on Dolphin terminals. Please consult the Dolphin SDK Add-on to find out how to enable dynamic screen rotation. There are three tabs: Alignment, Clear Type, and Text Size. Screen opens to the Alignment tab. Alignment Tab On this tab, you can re-align the screen. You first align the screen at bootup.
Text Size Tab The Text Size tab enables you to perform font scaling within certain views of the Today screen, Contacts, Calendar, Messaging, and Tasks. This means that you can increase or decrease the point size of the font on application windows. This is the default font size setting. To change the font size, move the slider toward Smallest or Largest. The Example text changes to reflect the font change. Tap OK to save the new font size setting.
7 Wireless Communication Connections Tab The Connections system setting provides access to the terminal’s various wireless communication options. Icon Setting Tapping this icon… See Page Beam Enables infrared communication. 7-9 Bluetooth Configures the Bluetooth radio. This icon appears only if a Bluetooth radio and driver is installed on the terminal. 9-1 Connections Opens Microsoft’s connections manager. 7-4 Dolphin Wireless Manager Manages the wireless radios installed in the terminal.
Using Infrared Using the IrDA port, you can send and receive data between the terminal and other devices equipped with infrared. This can include, but is not limited to, Windows Mobile information such as Contacts and Tasks, as well as software upgrades. The maximum data transfer speed is 115 Kbps. IrDA Port Location IrDA Port To send or receive, the IrDA ports of both devices - whether it’s two terminals, or a terminal and a host device - must be aligned with each other and within a close range.
5. When the IrDA port finds the aligned IrDA port, it immediately starts sending the selected file. The selected device reads “Sending.” 6. When the file transfer is complete, the selected device reads “Done.” Receiving Data The Beam Setting must be set to receive for the terminal to receive data from other infrared devices. 1. Verify that beam settings are set to receive. Tap Start > Settings > Connections tab > Beam. The Beam Settings window should appear as follows: 1. Align the IrDA ports. 2.
Connections Manager Microsoft’s connection manager sets up multiple network connections to Internet Service Providers (ISPs) via external modem. Do NOT enter connection parameters in the connections manager if: • You are using one of the on-board wireless radios to connect to a network. The Dolphin terminal uses the settings from each radio’s configuration utility to connect. • You are using Wireless Zero Config (WZC). By default, WZC is disabled on Dolphin terminals.
To complete the setup screens, obtain the network parameters from your system administrator. *Proxy Server Connections If you are connected to your ISP or private network during synchronization, the terminal should download the proper proxy settings during synchronization with the PC. If these settings are not on your PC or need to be changed, ask your ISP or network administrator for the proxy sever name, server type, port, type of Socks protocol used, and your user name and password.
Dolphin Wireless Manager The Dolphin Wireless Manager provides a centralized interface that enables and disables all the on-board radios. Each radio has its own configuration program and the Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio. Dolphin Wireless Manager Window Tap Start > Settings > Connections tab > Dolphin Wireless Manager . If a rectangle is grayed-out, then the radio is not installed on the terminal.
3. Tap OK and the radio begins activating. 4. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON. Note: If applicable, information about the radio appears in the rectangle. Accessing Radio Configuration Utilities Each of the three radios have their own configuration utilities that you can access through the Menu. There are three radio configuration utilities: For 802.11b/g Tap WLAN Settings and the Honeywell WLAN Security Supplicant opens.
Installing Additional Software In addition to the default programs installed on your terminal when it is first booted up, you can install any program (created for a Windows Mobile-based device), as long as the terminal has enough memory to store the program and the program has an EXE, CAB, or DLL extension. The most popular place to find software on the Windows Mobile website: www.microsoft.
3. Depending on the program, you may need to open File Explorer on the terminal, navigate to the folder where the program is located, and tap on the program file to install it. • If you copied the file to the Autoinstall folder, you can either tap on the program inside the Autoinstall folder or perform a hard reset and the program will install as part of the regular Autoinstall; see Let Autoinstall Run on page 2-3.
COM Port Assignment Table COM Port Assignment COM Port 1 Serial port. This is the 17-pin connector on the bottom panel of Dolphin terminals. COM Port 2 Bluetooth Module If there is no Bluetooth hardware installed on the terminal, this com port is unassigned. COM Port 3 Raw Infrared COM Port 4 COM Port 5 USB virtual serial port COM Port 6 IrDA, if IrDA is enabled. COM Ports 7-9 Unassigned.
8 Working with GSM (Only for HD5990LUP) Overview The Dolphin 9900 can be configured with an integrated Siemens® GSM/GPRS quad-band radio module for WWAN communications. GSM Short for Global System for Mobile communications, GSM is an open, non-proprietary wireless WAN system that is constantly evolving and growing. GPRS Short for General Packet Radio Service, GPRS is a non-voice value added service that allows packet-switched data to be instantly sent and received across mobile telephone networks.
SIM Card Installation Short for Subscriber Information Module, a SIM card stores the subscriber's personal information, GSM/ GPRS radio settings, security keys, contacts, etc. SIM cards are installed in compatible mobile devices, enabling you to switch devices without losing personal and setup information. SIM Card Requirements Before installing the SIM card: • The SIM card must be activated by the service provider. • The terminal must be powered down.
5. Place the SIM card door over the secured SIM card and fasten the screws. Screws SIM Card Door SIM Card SIM Card Interface 6. Install the battery pack and turn on the terminal. Enabling the GSM Radio Be default, the GSM radio should be enabled after each hard reset. Verify the status of the radio in the Dolphin Wireless Manager. Tap Start > Settings > Connections tab > Dolphin Wireless Manager . If the Phone is set to OFF, tap the Phone rectangle and the GSM radio enables.
Voice Communication You can use the Dolphin terminal as a phone over the GSM radio. Audio Modes The back panel of the Dolphin 9900 contains both a speaker and a microphone that you can use to send and receive audio signals over the GSM network; see Back Panel Features on page 3-6. There are two audio modes: Headset Headset mode is when you plug a headset into the audio jack and speak into the microphone. You must use a 2.5mm plug; no other audio plug will fit.
Sending Calls After the number is dialed, tap Talk Note: The or use the keyboard. icon indicated that the phone is in use. Ending Calls While the phone call is live, tap End or use the physical keyboard. Keyboard Combinations for Calls Keyboard To Send a Call, Press… To End a Call, Press… 43-key keyboard Blue + NUM Blue + ENT 56-key keyboard Blue + SFT Blue + ENT Dolphin® 9900 Mobile Computer User’s Guide–Preliminary Rev (a) 02 3/5/08 View Options Tap Menu > View.
Setup Options Tap Menu > Options. The Phone Settings tab windows appear. Phone Tab Services Tab Establish or change a PIN on the Phone tab. For each service, the phone will read You can set networks on the Network settings from the network on the SIM tab. and display the available options from the carrier.
Data Communication You set up data communication via the connections manager. The carrier on the SIM card is the ISP. System Requirements • The GSM radio must be enabled; see Enabling the GSM Radio on page 8-3. • You must have an active SIM card installed; see SIM Card Installation on page 8-2. • The Phone must not be in use. The the phone is not in use.
4. Enter the APN and tap Next. 5. Enter the username and password from the account and tap Finish. 6. On the Connections window, tap Manage existing connections. The connection you just created should appear in the list on the modem tab.
7. Tap and hold on the connection and select Connect on the popup menu. 8. The network icon in the navigation bar indicates the GSM radio is attempting to connect 9. When the connection is complete, the network icon changes to: . . 10. You can now send data over GSM. Ending the Data Connection You need to end the data connection to use the phone. By default, the data connection will disconnect after a certain amount of time passes without use. This period of time is determined by ISP.
8 - 10 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
9 Working with Bluetooth Enabling the Bluetooth Radio You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 7-6). 1. Tap Start > Settings > Connections tab > Dolphin Wireless Manager 2. Tap anywhere inside the Bluetooth rectangle. 3. Tap OK and Bluetooth begins activating. . 4. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON. Now, the Bluetooth radio is transmitting a signal.
Connecting to Other Bluetooth Devices 1. In the Dolphin Wireless Manager, tap Menu > Bluetooth Settings. OR Start > Settings > Connections tab > Bluetooth . 2. Tap Add new device. The terminal begins searching for discoverable Bluetooth devices. 3. 9-2 Select a device in the list and tap Next.
4. You are prompted to enter a passcode. If the device you are attempting to connect to has a specific passcode, enter it in the Passcode field and tap Next. If the device you are attempting to connect to does not have a specific passcode, enter one in the Passcode field and tap Next. The Bluetooth radio tries to connect with the device. 5. If you created a passcode, you will be prompted by the other device to enter the same passcode. Enter the created passcode to establish a connection.
7. 9-4 Select the services you want to use and tap Finish. The device appears in the list on the main window.
Types of Devices and Services When you tap Add new device on the Devices tab, the Bluetooth radio scans for discoverable Bluetooth devices, which appear in a list. Device Types The different types of devices each have an icon.
Transferring Files Via Bluetooth 1. Tap Start > Programs > File Explorer. 2. Navigate to the file you want to transfer. 3. Tap and hold on the file and select Beam File on the popup menu. 4. Bluetooth begins searching for devices. When a Bluetooth device is first found, it appears as an Unknown device; the icon indicates that the device is a Bluetooth device. As data is retrieved, the device IDs appear in the list. 5. Tap the device to begin sending the selected file. 6.
Making the Terminal Discoverable By default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by other Bluetooth devices. To make the terminal discoverable, tap the Mode tab. Select Make this device visible to other devices.
9-8 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
10 Dolphin HomeBase Overview As the hub of your Dolphin system, the Dolphin HomeBase charging and communication cradle supports both RS-232 and USB communications, which make it able to interface with the majority of PC-based enterprise systems. When a terminal is seated in the HomeBase, its main battery pack charges in less than four hours. Power The HomeBase completes a full charge of the main battery pack in less than four hours.
Dolphin HomeBase Parts and Functions Front Panel Terminal Well Auxiliary Battery Well DOCK LED AUX Battery LED COMM LED Terminal Well Place the Dolphin terminal in this well to communicate with a host device, power the terminal, and charge its battery pack. If the host device is a desktop computer that uses ActiveSync, synchronization begins immediately. While seated in the terminal well, the main battery installed in the terminal charges.
COMM LED This is the communication LED. It indicates the status of data transfer between the Dolphin terminal and the host device. The color of this LED differs if the HomeBase is using the serial or USB port connection. If using the serial port This color means… Red Serial data is being sent from the host device to the Dolphin HomeBase. Green Serial data is being sent from the HomeBase device to the Host Device. Orange Serial data is being sent at high data rates.
USB Port This USB Port is full-speed and 2.0 compliant. Using a USB cable, you can connect the HomeBase to a peripheral device, such as a desktop computer or printer. When the Dolphin terminal is seated in the terminal well, it is connected to the peripheral device via the HomeBase. The USB port on the HomeBase requires that you use ActiveSync 4.1 or higher. RS-232 Port Use a 9-pin, RS-232 cable from Honeywell to connect this port to a peripheral device for RS232 data communication.
HomeBase Serial Connector The following diagram displays the pin diagram of the serial connector of the HomeBase. Note: Signals referenced are for a DTE device. The HomeBase is at a right-angle to the printed circuit board (PCB). The ninth pin has a ring indicator (RI).
Charging the Main Battery The Dolphin HomeBase powers the terminal and fully charges its main battery pack in less than four hours. The HomeBase contains an intelligent battery charging system that protects the battery from being damaged by overcharging. The unit senses when a battery pack is fully charged and automatically switches to a trickle charge that maintains the battery at full capacity.
Communications USB Dolphin terminals support USB communications out of the box. The HomeBase also supports USB communications via the USB port located on the back. The HomeBase acts as a USB device by interfacing the USB signals of the Dolphin terminal to the USB of the host workstation. Using a standard USB cable, the HomeBase’s USB interface allows the Dolphin terminal to communicate with a personal computer or to be networked through a USB hub.
Communicating with the Dolphin Terminal To initiate communications between the Dolphin terminal and peripheral, complete these steps: 1. Insert the Dolphin terminal into the terminal well of the HomeBase. • The DOCK LED illuminates green. If the DOCK LED does not illuminate, make sure that the terminal is properly seated. You may need to remove and re-insert the terminal. • The Dolphin terminal activates; if the power is off, the terminal automatically powers on.
RS-232 Communications Cables Connect the HomeBase to the host computer or other device by plugging an RS-232 serial cable into the RS-232 Communications Port on the rear of the HomeBase. The wiring of your cable depends on whether the other device is set up as a Data Communications Equipment (DCE) or Data Terminal Equipment (DTE) device. The HomeBase Communication Port is configured as a DCE device.
Mounting the HomeBase Set the Dolphin HomeBase on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal while it is in the HomeBase.
Wall Mounting You can purchase a wall mount kit that contains • a mounting bracket, • three screws, and • six washer/nut sets. 1. Insert a screw into the round end of each screw slot on the bottom panel. Slide each screw towards the narrow end of the slot. Then, use a washer/nut set on each screw to secure the screw in the slot. 2. Attach the bottom panel to the mounting bracket; match the holes to the secured screws. 3.
10 - 12 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
11 Dolphin Mobile Base Overview The Dolphin Mobile Base charging and communication cradle is designed specifically for in-premise and in-transit data collection applications. It features a flexible mounting bracket, a cigarette lighter adapter, and a power cable to adapt it to your environment. When a terminal is seated in the Mobile Base, its main battery pack charges in less than four hours. The serial connector supports RS-232 communication and power out to peripheral devices, such as hand held scanners.
Mobile Base Parts and Functions Front Panel The front panel of the Mobile Base has one slot. The following graphic features the Mobile Base with the terminal inserted into the terminal well. Terminal Well Mounting Brackets DOCK LED COMM LED Terminal Well Place the terminal in this well to communicate with a host device and charge the main battery pack. Mounting Brackets Use these to mount the Mobile Base to a fixed location.
Bottom Panel The power supply and RS-232 connectors are located on the bottom of the unit. Power Supply Connector RS-232 Communications Port Power Supply Connector Use this connector to attach a Honeywell power cable to the Dolphin Mobile Base. The Mobile Base can be powered by an external DC power source of between 11 VDC to 48 VDC. To run on vehicle power, you can use the 12 VDC cable or 24 VDC cable option. The appropriate cable comes with the kit you ordered.
Powering the Dolphin Terminal When seated in a Mobile Base that is connected to the appropriate power source, the Dolphin terminal receives the power to charge its main battery and run its internal circuitry. Keep the Mobile Base plugged into the power source so that the Dolphin terminal battery pack stays fully charged. For more information about powering the Mobile Base, see Powering the Dolphin Mobile Base on page 11-6.
Installing the Dolphin Mobile Base To install the Dolphin Mobile Base, you need to mount it securely to an appropriate location and supply it with power. Mounting the Mobile Base The adjustable mounting bracket holds the terminal securely in place and gives the user a variety of options for mounting the Mobile Base. When selecting a location, keep in mind that the power supply and serial connectors point straight out the bottom panel. 1. Loosen the turnscrew. 2.
Locking Tabs When positioned as shown in the above graphic, the locking tabs secure the spring arm assembly, latch, and terminal in place. When seating a terminal, turn both arms up to allow the spring arm to move as necessary while the terminal is being inserted. After the terminal is seated, turn both arms toward the center to lock them. Both locking tabs must be pointing up to insert or remove a terminal in the Mobile Base.
Establishing Communication with the Mobile Base The Mobile Base RS-232 interface allows the Dolphin terminal to communicate to a personal computer, modem, or any standard RS-232 device using a standard serial cable and communications software. Requirements To use the HomeBase for communications, you need the following equipment: • A Mobile Base powered by a power cable and power adapter cable from Honeywell • The RS-232 communications cable • ActiveSync v4.
RS-232 Pin Configuration Mobile Base /Host Port (DCE) IBM AT DB9 (DTE) IBM XT DB25 (DTE) Modem DB25 (DCE) Pin / Input Signal 2 / (RD) 2 3 2 3 / (TD) 3 2 3 5 / (SG) 5 7 7 4 / (DTR) 4 20 6 6 / (DSR) 6 6 20 7 / (RTS) 7 4 5 8 / (CTS) 8 5 4 Refer to this table if you want to make your own cables. To do so, you must determine if your host RS232 device is • 9-pin or 25-pin and • configured as a DCE or DTE device.
The following diagram displays the pin diagram of the serial connector of the bottom panel of the Mobile Base. Pin # Description 1 2 3 4 5 6 7 8 9 Internal Jumper to Pin 6 TXD RXD DSR GND DTR CTS RTS 5 VOLT OUT Note: Signals referenced are for a DTE device.
11 - 10 Rev (a) 02 3/5/08 Dolphin® 9900 Mobile Computer User’s Guide–Preliminary
12 Dolphin ChargeBase Overview The Dolphin ChargeBase is a four-slot charging cradle that can power four Dolphin terminals, and charge their main batteries in less than four hours. Charging The Dolphin ChargeBase completes a full charge of the main battery pack in less than four hours. The ChargeBase also provides power to the intelligent battery charging system in all Dolphin terminals that senses when a full charge has been achieved and switches to a trickle charge to maintain the full charge.
Dolphin ChargeBase Parts and Functions Front Panel Terminal Wells Dock LED Charge LED Terminal Wells The ChargeBase contains four terminals wells. Each well • Holds and charges the main battery pack of one Dolphin terminal. • Contains the companion to the I/O connector on the bottom panel of Dolphin terminals. • Has two LEDs on the front: the Dock LED and the Charge LED.
Power Supply The ChargeBase includes a power supply that contains a power adapter to ensure the proper voltage. The power adapter is plugged into standard AC/DC outlets.
Supplying Power to the ChargeBase Using a non-Hand Held Products power adapter voids your warranty and could result in serious damage to the circuitry of the Dolphin ChargeBase. ! 1. Be sure the power switch on the power adapter is in the OFF position. 2. Plug the power cord into the power adapter. 3. Plug the power connector cable into the power connector on the back panel of the ChargeBase. 4. Plug the power cord into a standard wall outlet. 5.
Charging Terminals in the ChargeBase The Dolphin ChargeBase charges the main battery of each terminal in less than four hours. The ChargeBase uses the intelligent battery charging system incorporated into all Dolphin terminals that prevents overcharging. This means that Dolphin terminals may be stored in the ChargeBase indefinitely without damage to the terminals, battery packs, or the ChargeBase. 1. Power the ChargeBase; see Supplying Power to the ChargeBase on page 12-4. 2.
Using the DIN Rail All Dolphin charging/communication cradles have a DIN rail (7.5 X 35 mm) slot on the bottom panel to enable secure mounting. 1. Slide the DIN Rail into the DIN Rail slot on the bottom panel. 2. Turn the ChargeBase and DIN Rail right side up. 3. Secure the DIN Rail to a stable, flat horizontal surface.
Using the Wall Mount Kit Wall mount kits can be purchased separately to secure the ChargeBase to a wall or other vertical surface. For the ChargeBase, you need to purchase two kits so that you have two mounting brackets, one for each end of the ChargeBase. Each mounting bracket contains an open slot in the back to accommodate the connector cables. 1. Insert the head of each screw into the round end of each of the four screw slots on the bottom panel.
4. Using the remaining washer and nut sets, secure the mounting brackets to the bottom panel. 5. Secure the mounting brackets to an appropriate vertical surface.
13 Dolphin QuadCharger Overview The Dolphin QuadCharger is a four-slot charging station that provides intelligent battery management for the Li-ion battery packs used in Dolphin terminals. Batteries charge in less than four hours. The fourth slot features a battery analyzer that completely resets a battery, then displays its remaining capacity. Compatibility The QuadCharger is compatible with the Li-ion batteries that power the Dolphin terminals.
Dolphin QuadCharger Parts and Functions Top Panel Status LED 1 2 3 4 SLOT 4 BATT ER CAPAC Y ITY Battery Capacity LEDs 100% 0% ANALYZ E O CHAR GE/AN Analyze Button ALYZE Charging Slots Charge/Analyze Slot Charging Slots The QuadCharger contains four charging slots. Each slot holds one Li-ion battery and charges it independently of the other slots. When a battery is placed in each slot, it immediately begins charging.
Back Panel O CHARGE/ANALYZE ALYZE 0% 0% PACITY TTERY LOT 4 1 3 2 4 Swc Power Switch Status LED Power Supply Connector Power Switch Toggle the power switch to turn the QuadCharger on and off. Power Supply Connector Use this connector to attach the power supply to the QuadCharger. The universal power supply accepts input voltages between 90-265 volts.
4. Press the power switch to the ON position. The power LED illuminates green, and the charger performs a self-diagnostic test that lasts approximately five seconds. Inserting and Removing Battery Packs To insert a battery pack, place the end of the battery without the locking tab into the bottom of the charging pocket and snap the battery into place with a hinging motion. The Status LED for that particular slot illuminates orange when the battery has been properly inserted.
Using the Battery Analyzer Purpose Using the Charge/Analyze slot helps you monitor the charge capacity of Li-ion batteries over time. Location The battery analyzer is located in the fourth slot - named the Charge/Analyze slot - of the ChargeBase. Only a battery placed in this slot can be run through an Analyze cycle. This slot contains Battery Capacity LEDs along the right side.
Mounting the QuadCharger The Dolphin QuadCharger should be on a dry, stable surface. To easily adapt the QuadCharger to your environment, it can be mounted on a flat, horizontal surface such as a desktop or workbench, or a flat, vertical surface such as a wall. When choosing a location, always bear in mind that • the mounting location must allow users easy access to power switch and power connector.
Wall Mounting The following graphic displays how to mount a QuadCharger to a wall: Dolphin® 9900 Mobile Computer User’s Guide–Preliminary Rev (a) 02 3/5/08 13 - 7
Troubleshooting If you encounter problems with your Dolphin QuadCharger, refer to chart below for possible solutions. If problems persist, please contact Honeywell Technical Support. Problem Issue The Status LED does not come on when I insert a battery pack into the Dolphin QuadCharger. Check the power connections on the Dolphin QuadCharger; make sure the POWER switch is ON and the battery pack is properly seated. The Status LED lights red during charging.
14 Customer Support Product Service and Repair Honeywell provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product. North America Telephone: (800) 782-4263 Fax: (803) 835-8012 E-mail: naservice@handheld.
Technical Assistance If you need assistance installing or troubleshooting, please call your Distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 Fax number: (315) 554-6705 E-mail: natechsupport@handheld.com Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 E-mail: latechsupport@handheld.com Brazil Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105 E-mail: brsuporte@handheld.
Limited Warranty Honeywell International Inc. ("Honeywell") warrants its products to be free from defects in materials and workmanship and to conform to Honeywell’s published specifications applicable to the products purchased at the time of shipment.
Use only power adapters approved for use by Hand Held Products. Failure to do so may result in improper operation or damage to the unit and will void the warranty. How to Extend Your Warranty Honeywell offers a variety of service plans on our hardware products. These agreements offer continued coverage for your equipment after the initial warranty expires.
Honeywell 700 Visions Drive P.O.