Dolphin® 9500/9550 Mobile Computer Windows® Powered Pocket PC 2002 User’s Guide - GSM Draft ™
Trademarks Dolphin, HomeBase, Mobile Base, and QuadCharger are trademarks or registered trademarks of Hand Held Products, Inc. Microsoft Pocket PC 2002, Windows, Windows NT, Windows 2000, Windows ME, Windows XP, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. Intel is a registered trademark of Intel Corporation. Chapter 7 (pages 7-1–7-11) contains copyrighted information from SyChip, Inc.
Table of Contents Chapter 1 - Introduction Required Safety Labels ....................................................................................................................... 1-2 Location........................................................................................................................................ 1-2 Dolphin 9500/9550 Batch Terminal.............................................................................................
Batteries ............................................................................................................................................ 3-10 Main Battery Pack ...................................................................................................................... 3-10 The Li-ion battery pack requires four hours to charge completely. ........................................... 3-10 Internal Backup Battery............................................................................
Notifications...................................................................................................................................... 4-25 Finding and Organizing Information ................................................................................................ 4-26 Chapter 5 - Settings Overview............................................................................................................................................. 5-1 Personal Tab..................................
Chapter 7 - Wireless LAN Communications with 802.11b Overview............................................................................................................................................. 7-1 Powering Up the 802.11b Radio Driver ....................................................................................... 7-1 Configuring the 802.11b Radio...........................................................................................................
Chapter 9 - Wireless WAN Communications with GSM/GPRS Overview............................................................................................................................................. 9-1 Powering Up the GSM/GPRS Radio Driver ................................................................................ 9-1 Capabilities ................................................................................................................................... 9-1 Tri-Band Antenna................
Chapter 10 - Applications Calendar: Scheduling Appointments and Meetings.......................................................................... 10-1 Using the Summary Screen ........................................................................................................ 10-3 Creating Meeting Requests ........................................................................................................ 10-3 Contacts.................................................................................
Communications ............................................................................................................................... 11-8 Communications Types .............................................................................................................. 11-8 Equipment Requirements ........................................................................................................... 11-8 Setting up the HomeBase for RS-232 Communications .........................................
Chapter 14 - Dolphin 9500/9550 QuadCharger Overview........................................................................................................................................... 14-1 Dolphin QuadCharger Parts and Functions ...................................................................................... 14-1 Front Panel ................................................................................................................................ 14-1 Rear Panel............................
1 Introduction Congratulations on the Purchase of Your New Dolphin 9500 or Dolphin 9550 Mobile Computer! You have made a wise choice in selecting the Dolphin, a device known worldwide for its ergonomic form factor, light-weight, rugged design and single-handed data collection capabilities. Ergonomics The patented shape of the Dolphin 9500 fits into either hand comfortably with major function keys that are easy to access.
Required Safety Labels The Dolphin 9500/9550 mobile computer meets or exceeds the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your Dolphin mobile computer. Location Safety labels appear on the back panel of both terminals.
Regulatory and Safety Approvals for all Dolphin 9500/9550 Terminals Parameter Specification U.S.A Canada European Community FCC Part 15, Class B ICES-003 EN 55022 (CISPR 22) Class B EN60950 EN60825-1 EN55024: 1998 The CE Mark on the product indicates that the system has been tested to and conforms with the provisions noted within the 89/336/EEC Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage Directive. For further information, please contact: Hand Held Products, Inc.
Dolphin 9500/9550 WLAN or WPAN Radio THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY AND CONFIDENTIAL MATERIAL OF HAND HELD PRODUCTS, INC.
Dolphin 9500 WWAN Radio THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY AND CONFIDENTIAL MATERIAL OF HAND HELD PRODUCTS, INC. AND SHALL NOT BE REPRODUCED, OR COPIED, OR USED A BASIS FOR MANUFACTURE OR SALE on safe levels of RF energy The Dolphin 9500 RF terminal is designed to comply withAS the most current applicable standards OF of EQUIPMENT DEVICES WITHOUT WRITTEN PERMISSION.
FCC Compliance Dolphin mobile computers meet or exceed all applicable standards and have been manufactured to the highest level of quality. Dolphin 9500/9550 Batch Terminal Dolphin 9500/9550 Batch terminals comply with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Dolphin 9500/9550 RF Terminal with 802.
RF, Regulatory, and Safety Agency Approvals Parameter Specification RF Approvals U.S.A Canada Europe Mexico FCC Part 15.247 RSS 210 ETS 300 328 Telecom RCPHAD002-485 Dolphin 9500/9550 802.11b, GSM, and/or Bluetooth R&TTE Compliance Statement The HHP Dolphin 9500RF and Dolphin 9550RF are in conformity with all essential requirements of the R&TTE Directive (1999/ 5/EC).
1-8 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
2 Getting Started Overview The Dolphin 9500/9550 mobile computer is designed for easy, single-handed mobile data collection. Each mobile computer is equipped with a PXA255 400MHz RISC processor built to run the Pocket PC platform. Dolphin 9500/9550 computers are available with different types of 2D imagers and wireless radios to meet most any enterprise mobile data collection requirement. There are three keyboard options and a 240 x 320 pixel, backlit 1/4 VGA display available in color or monochrome.
Dolphin 9500/9550 Models and Options HHP’s family of Dolphin 9500/9550 mobile data collection terminals includes these models: The Dolphin 9500 Batch This is a Pocket PC mobile computer with a unique, ergonomic shape designed for single-handed use. The standard Dolphin 9500 is available with 64 MB RAM and 32 MB non-volatile Flash and integrated digital imager. An optional Secure Digital (SD) memory interface offers additional memory.
Dolphin 9500/9550 Peripherals Each of the following items is sold separately to enhance your Dolphin 9500/9550 terminals capabilities. Dolphin HomeBase™ The Dolphin HomeBase charging and communication cradle supports both RS-232 and USB communications, which enable it to interface with the majority of PC-based enterprise systems. When a terminal is seated in the HomeBase, its main battery pack charges in less that four hours.
Dolphin 9500/9550 Accessories Each of the following items is sold separately to enhance your Dolphin 9500/9550 terminals capabilities. Charging/Communication Cables USB and serial cables connect the Dolphin 9500/9550 directly to both a peripheral device for communication and a power source for charging. Dolphin Mobile Charger This charging cable plugs the terminal directly into a vehicle cigarette lighter/power port to power the terminal and charge the battery pack.
Bar Code Symbologies Supported Symbology type Symbologies supported 1D Symbologies Codabar Code 3 of 9 Code 11 Code 32 Pharmaceutical (PARAF) Code 93 Code 128 EAN with Add-On and EAN with Extended Coupon Code EAN-13 Interleaved 2 or 5 Matrix 2 of 5 Plessey PosiCode RSS Straight 2 of 5 IATA Straight 2 of 5 Industrial Telepen Trioptic Code UCC/EAN-128 UPC and UPC-A 2D Symbologies Aztec Code 16K Composite Data Matrix MaxiCode OCR PDF417 QR RSS Composite Codes Aztec Mesa Codablock F EAN·UCC RSS-14 OCR C
Using the Dolphin 9500/9550 for the First Time Step 1. Unpack the Carton and Verify its Contents Verify that the carton contains the following items: • Dolphin 9500/9550 mobile computer (the terminal) • Main battery pack (7.4v Li-Ion) • Microsoft Companion CD • Dolphin 9500 Quick Start Guide Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service. For details, see Return Information on page 15-2.
! Use only Dolphin 9500 series peripherals, power cables, and power adapters. Use of peripherals, cables, or power adapters not sold/manufactured by HHP will void the warranty and may damage the terminal. Using the Dolphin HomeBase D OL 1. Connect the HomeBase to the power supply provided by HHP. P H IN 950 0 2. Slide the terminal (with installed battery pack) into the terminal well until the Dock LED lights solid green to indicate that the terminal is properly seated. POWER SCA N 3.
Step 4. Initialize the Mobile Computer 1. When power is applied from a newly installed battery, the decode LED lights and the scan LED blinks for approximately three seconds. Do NOT press any keys while the terminal is booting up. 2. The terminal initializes and the HHP splash screen displays for a few seconds. The Build numbers indicate the software version number. Build: 5.XX/5.XX/5.XX Bootloader Keyboard Kernel 3. The system performs a hard reset.
Note: HHP recommends using screen protectors for Dolphin 9500/9550 terminals; especially for those terminals used within applications that require high-volume interfacing with the touch screen. Screen protectors help prevent damage to the touch screen and are easily installed. Screen protectors can be purchased at any major computer retail store or directly from HHP, Inc. Please contact HHP directly for part numbers and pricing. Step 7.
Step 8. Autoinstall For each program that loads, a status bar indicates that the program is loading. Autoinstall occurs after each hard reset. Do NOT touch the keyboard or the screen while programs are loading. All configurations of the Dolphin 9500/9550 install HHP Demos and HHP Utilities. If the terminal is configured with a wireless radio, the appropriate radio drivers (*.cabs) and utilities for each radio install. After Autoinstall is complete, the terminal performs a soft reset automatically.
Verify Decoding The Scan Demo enables you to decode a sample bar code. 1. Go to Start > HHP Demos > Scan Demo. 2. Aim the terminal at a bar code and press the SCAN key. The decode LED flashes red, the scan LED lights red, and a green aimer beam projects out from the scanner. 3. When a good scan is obtained, the decode LED lights solid green and the terminal beeps. The bar code readout appears on the screen. 4. Press the ESC key to close the demo.
Resetting the Terminal Soft Reset (Warm Boot) You would perform a soft reset if the terminal fails to respond. The soft reset re-boots the device without losing RAM data. 1. Press and hold the Control (CTRL) and the Shift (SFT) keys for approximately five seconds. 2. The decode and scan LEDs flash for approximately three seconds as the terminal resets. 3. When the reset is complete, the Today screen displays.
3 Dolphin 9500/9550 Overview System Features Processor The Dolphin 9500/9550 terminal is equipped with an Intel X-Scale 400MHz RISC microprocessor that runs on a 100 MHz RAM BUS, making it one of the most powerful Pocket PC platforms on the market. Operating System The Pocket PC platform is a compact, highly efficient, scalable operating system. Its open architecture facilitates development of applications for energy-efficient data collection devices like the Dolphin 9500/9550 terminal.
Front Panel Features This section describes features on the Dolphin 9500/9550 terminal front panel.
Monochrome - The monochrome LCD is grayscale and 4 bits/pixel. The backlight illuminates when the touch screen or the Backlight key is pressed. Monochrome units contain an addition contrast setting to enhance readability. For more information about the Backlight, see Adjusting the Backlight on page 4-15. SCAN Key The SCAN key is centrally located for easy access with the right or left hand. When pressed, the SCAN key activates the scanner/imager.
Back Panel Features Because the back panel of the Dolphin 9500 and the Dolphin 9550 are different, each is featured in its own section. Dolphin 9500 The following graphic describes features on the back panel of the Dolphin 9500 terminal.
Speaker The Dolphin 9500/9550 terminal has an integrated speaker that sounds audio signals as you scan bar code labels and enter data. The operating frequency range is 500Hz at 71 dB up to 80 dB. The speaker can also be used for playing sounds (e.g., WAV files). Hand Strap The Dolphin 9500 has an integrated elastic hand strap to provide a comfortable, secure grip on the terminal. It is attached to the terminal with a clip on the bottom panel; see Hand strap clip on page 3-9.
Dolphin 9550 This section describes the back panel of the Dolphin 9550. It contains the same features as the Dolphin 9500 described in the previous section with the additions of • a pistol-grip handle to hold and maneuver the terminal with greater ease, • a scanner/imager trigger on the handle that activates the scan, and • rubber bumpers that enable the terminal to rest safely and securely when not in use. The following is a graphic of the 9550 back panel.
Rubber Bumpers The rubber bumpers enable the Dolphin 9550 to rest in a stable, nose-down position when the unit is set on a flat surface. The following graphic shows the Dolphin 9550 in a nose-down position, resting on its rubber bumpers. Rubber Bumpers Stylus - inside the handle Stylus The stylus is used to operate the touch screen display. The Dolphin 9550 stores the stylus inside the pistol-grip handle.
Side Panel Features DOL P H IN 9 500 The following graphic shows the left, side panel. IrDA Port Access Door to the Secure Digital (SD) memory interface Audio Jack (2.5mm) IrDA Port The Infrared Data Association or IrDA port communicates with IrDA-enabled devices such as PC’s, printers, modems, or other Dolphin 9500/9550 terminals. The maximum speed is 115kbps. Secure Digital Memory Interface Dolphin 9500/9550 terminals have an industry standard Secure Digital (SD) memory interface.
Bottom Panel Features This following graphics describe the bottom panel of the Dolphin 9500/9550. Hand strap clip 1 3 2 10 11 4 5 6 12 13 14 7 15 8 9 16 17 Mechanical Connector Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Description +USB PWR N/C N/C N/C N/C GND 5V OUT DTR -USB USB DET RI DSR RXD RTS TXD CTS Note: Signals referenced are for a DTE device. Mechanical Connector The bottom panel of the Dolphin 9500/9550 features a custom, industrial-grade connector with 17 pins.
Batteries The Dolphin 9500/9550 features intelligent battery technology. It is comprised of two types of battery power: the main battery pack installed in the back panel and the backup battery located inside the terminal. They are designed to work together to prevent data loss when the terminal is in use over long periods. Both must be completely charged before using the Dolphin 9500/9550 for the first time. Main Battery Pack ! Use only the Li-ion battery packs provided by HHP.
Managing Battery Power Data and files saved on the Dolphin 9500/9550 terminal may be stored in RAM, so it is important to maintain a continuous power supply to the terminal. When the main battery pack becomes low, the Low Battery Charge icon appears in the notification tray at the top of the screen. The Critical icon appears when the battery is critically low. There is also a Low Battery icon that appears when the backup battery is low. For details about these icons, see Status Icons on page 4-25.
Checking Battery Power 1. Go to Start > Settings > System tab > Power. The power settings screen appears displaying the charge status of both the installed Li-ion battery pack and the NiMH backup battery inside the terminal. This screen also displays the Suspend Mode settings for the terminal. 2. Select your time-out preferences from the drop-down lists. You can have both battery power and external power settings simultaneously. 3. Tap OK to save the changes and exit.
Dolphin 9500/9550 Technical Specifications System Architecture Processor: Intel X-Scale PXA255 400MHz Development Environment: Dolphin SDK for Pocket PC 2002 supports Embedded VB or C++ Dolphin .NET SDK for Pocket PC 2002 supports Visual Studio.NET(VB.NET and C#.
Dolphin 9500/9550 Technical Specifications Weight: 9500 Terminal – Batch: 19.7 oz. (558 gm) WLAN: 20.2 oz. (573 gm) WPAN: 20 oz. (567 gm) WLAN/WPAN: 20.3 oz. (576 gm) 9550 Terminal – Batch: 23.4 oz. (663 gm) WLAN: 23.9 oz. (677.
4 Using the Dolphin 9500/9550 Mobile Computer Entering Data To enter data, you may: • Use the 35-key, 43-key, or 56-key keyboards • Capture images or scan bar code data into data fields • Use the Soft Input Panel (SIP) to enter text • Write directly on the screen • Draw pictures on the screen • Use Microsoft® ActiveSync® to synchronize or copy information from your desktop computer. For more information on ActiveSync, see ActiveSync Help on your desktop computer.
Today Screen When you turn on your device for the first time, you see the Today screen. You can also display it by tapping Start and then Today. On the Today screen, you can see at a glance important information for the day. Tap to switch to a program. Tap to view notification messages. Tap to change volume or mute all sounds. Tap to change date and time. Tap to open an item. Your day at a glance. Tap to create a new item. 4-2 Tap to view connection status.
Navigation Bar The navigation bar is located at the top of the screen. It displays the active program and current time, and allows you to switch to programs and close screens. Tap to change volume or mute the device. Tap to quickly select a program you have recently used. Tap to select a program. Tap to see additional programs. Tap to customize the device. Command Bar Use the command bar at the bottom of the screen to perform tasks in programs.
Pop-Up Menus With pop-up menus, you can quickly choose an action for an item. For example, you can use the pop-up menu in the contact list to quickly delete a contact, make a copy of a contact, or send an e-mail message to a contact. The actions in the pop-up menus vary from program to program. To access a pop-up menu, tap and hold the stylus on the item name of the action you want to perform the action. When the menu appears, lift the stylus, and tap the action you want to perform.
Selecting Programs To select a program, tap Start > Programs, then the program name. Note: Some programs have abbreviated labels for check boxes and drop-down lists. To see the full spelling of an abbreviated label, tap and hold the stylus on the label. Drag the stylus off the label so that the command is not carried out.
Imager The terminal houses a compact image engine that instantly reads all popular 1D and 2D bar codes. It also supports omnidirectional aiming and decoding for greater flexibility in handling the device in real-world settings. The imager can also capture digital images, such as signatures and pictures of damaged inventory. Images are saved in industry-standard file formats.
Scanning Position Options The aiming beam is smaller when the terminal is held closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should be read farther from the unit.
Capturing Images The image-capture process is an intuitive, split-second operation for experienced users. By following the basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to adapt it to different application environments. Image Preview When the imaging process is initiated, the Dolphin 9500/9550 touch screen displays a preview of the object. This is a live video image of what the imager is currently viewing.
Using the Keyboards The Dolphin 9500/9550 series features three keyboard options: 35-key numeric/alpha keyboard, 43-key numeric/alpha keyboard, and 56-key alpha/numeric keyboard. Each keyboard is backlit for easy viewing in various lighting conditions and contains centrally located keys for both right- and left-hand operation. The silver background of both the keys and the overlay enhances the readability of each.
Using the Function Keys Name Key Function Backlight By default, the Backlight key turns the keyboard backlight on and off. See Adjusting the Backlight on page 4-15. Backspace (BKSP) This key appears on both the 35- and 56-key keyboards. The BKSP key moves the cursor back one space each time the key is pressed. If you are typing text, it deletes the previous character each time it is pressed. On the 43-key keyboard, the backspace is a shifted function; press SFT + SP to backspace.
The up and down arrows can also be used for volume control when pressed in combination with the blue modifier key. They can also be used for page up and page down commands when pressed in combination with the red modifier key. Other functionality varies according to the application in use. Using the Modifier Keys All three versions of the Dolphin 9500/9550 keyboard feature the standard PC keyboard modifier keys, Shift (SFT), Alt, and Control (CTRL) as well as Blue and Red modifier keys.
35-Key Numeric/Alpha Keyboard The following graphic displays the 35-key numeric/alpha keyboard. SCAN key Power key Shift key Alpha Lock key Escape key Tab key Enter key Navigation keys Alpha Lock Indicators Space key Delete key Function keys Backspace key Backlight key CTRL, Blue, Red, ALT Modifier keys Alpha Lock Key (ALPHA) Because the 35-key keyboard defaults to numeric mode, the Alpha Lock key appears only on the 35-key keyboard.
43-Key Numeric/Alpha Keyboard The following graphic displays the 43-key numeric/alpha keyboard. SCAN key Escape key Power key Shift key Tab key Number Lock key Enter key Navigation keys Number Lock Indicators Backlight key (use with SFT to delete) Space key (use with SFT to backspace) CTRL, Blue, Red, ALT Modifier keys Number Lock (NUM) Because the 43-key keyboard defaults to alpha mode, the Number Lock key appears only on the 43-key keyboard.
56-Key Alpha/Numeric Keyboard The following graphic displays the 56-key numeric/alpha keyboard. SCAN key Power key Backlight key Shift key Insert key Escape key Tab key Enter key Navigation keys Space key Backspace key Delete key CTRL, Blue, Red, ALT Modifier keys Key Combinations There are keyboard combinations for specific functions and special characters on each keyboard. For charts of the key combinations associated with each keyboard layout, see the Appendix A of the Dolphin 9500/9550 User’s Guide.
Adjusting the Backlight Both the keyboard and the display are backlit to enable better viewing in low-light conditions. All keyboards contains a Backlight key that toggles the backlight on and off; see Backlight on page 4-10. Keyboard By default, the Backlight key turns the keyboard backlight on and off for both color display and monochrome terminals. Display Backlight functionality differs for color and monochrome displays. Color Display The backlight for the color display is user-defined.
Using the System Settings Tap Start > Settings > System tab > Contrast. The current settings are displayed. Use the slider to adjust the contrast to the desired setting. Tap OK to save adjustments.
Communication Media Options Via the Mechanical Connector The 17-pin, industrial-grade, mechanical connector on the bottom panel is designed to work only with HHP sold/manufactured communication and charging peripherals. Via these peripherals, the connector supports USB and RS-232 communications, enabling the user to connect the Dolphin 9500/9550 terminal to external devices such as scanners and printers.
Radio Options Dolphin 9500/9550 terminals can be configured with one or a combination of the following radios: • 802.11b • Bluetooth • GSM/GPRS (9500 only) Please note that the 9550 supports all radio options and configurations EXCEPT FOR GSM/GPRS. Available Radio Combinations Dolphin 9500/9550 terminals can be configured with more than one radio. Co-located Radios Some combinations are co-located, which means that you can use only one radio at a time.
Powering Up a Radio Requirements To successfully power up a radio, both the hardware module and the software driver must be installed on the terminal. If the module is present, the radio appears in the Radio Manager. However if the driver is not installed, you cannot successfully power up the radio. Attempting to do so produces an error in the Status field that tells you that the driver is not installed. To Power Up a Radio or Radio Combination 1.
Entering Text Using the Input Panel Use the input panel to enter information in any program on the Dolphin mobile computer. You can either type on the soft keyboard or write on the touch screen using Letter Recognizer or Block Recognizer. In either case, the characters appear as typed text on the screen. To show or hide the input panel, tap the Input Panel button. Tap the arrow next to the Input Panel button to see your choices. Select an input method. Tap to see your choices. Input Panel button.
2. Write a letter in the box. When you write a letter, it is converted to typed text that appears on the screen. For specific instructions on using Letter Recognizer, with Letter Recognizer open, tap the question mark next to the writing area . Using the Block Recognizer With Block Recognizer you can input character strokes using the stylus that are similar to those used on other devices. 1. Tap the arrow next to the Input Panel button and then Block Recognizer. 2. Write a letter in the box.
Input Panel Options You can set input options by going to Start > Settings > Personal tab > Input.
Writing on the Screen In any program that accepts writing, such as the Notes program, and in the Notes tab in Calendar, Contacts, and Tasks, you can use your stylus to write directly on the screen as you would on paper. To write on the screen, tap the Pen button to switch to writing mode. This action displays lines on the screen to help you write. Tap the Pen button and use your stylus like a pen. Note: Some programs that accept writing may not have the Pen button.
Drawing on the Screen Drawing on the screen is similar to writing on the screen. The difference between writing and drawing on the screen is how you select items and how they can be edited. To create a drawing, cross three ruled lines on your first stroke. A drawing box appears. Subsequent strokes in or touching the drawing box become part of the drawing. Drawings that do not cross three ruled lines will be treated as writing. For example, selected drawings can be resized, while writing cannot.
Status Icons Status Icon Meaning Turns all sounds on and off Backup battery is low Main batteries are charging Main batteries are low Main batteries are very low Main batteries are full Synchronization is beginning or ending Notification that one or more e-mail messages were received Note: The Notification icon displays if more notification icons need to be displayed than there is room to display them. Tap the icon to view all notification icons.
Finding and Organizing Information The Find feature on your Dolphin mobile computer helps you quickly locate information. On the Start menu, tap Find. Enter the text you want to find, select a data type, and then tap Go to start the search. To quickly find information that is taking up storage space on your device, select Larger than 64 KB in Type. You can also use the File Explorer to find files on your device and to organize these files into folders.
5 Settings Overview System settings are available off the Start menu. Go to Start > Settings and the system settings screen opens displaying the Personal tab. System settings are comprised of the following three tabs: Personal tab System tab Connections tab Personal tab Enables you to customize buttons, input methods, menus, etc. - see Personal Tab on page 5-2. System tab Enables you to adjust system settings - see System Tab on page 5-5.
Personal Tab To access the Personal tab, go to Start > Settings. The screen opens displaying the Personal tab. Button Name Tapping this icon enables you to … Buttons Customize buttons to perform functions. To use this setting, the HotKeys HHP Utility must be initialized. Tap Start > HHP Utils > HotKeys (the icon is the same). The HotKeys utility initializes. Return to the Personal tab and tap the Buttons icon. Input Customize the input panel. For details, see Input Panel Options on page 4-22.
Adding a Program to the Start Menu You can add existing programs you use often, such as File Explorer, to the Start menu for faster access. You are not installing the program, just re-routing access to it. Using System Settings 1. Tap Start > Settings > Personal tab > Menus > Start Menu tab. 2. Tap the check box for the program you want to add and tap OK to save. 3. Tap the Start menu. 4. Verify that the program appears.
3. Navigate to the Windows folder and open the Start Menu (My Device > Windows > Start Menu), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu. 4. Tap the Start menu. 5. Verify that the program now appears. Using ActiveSync on the Desktop Computer Here, you are performing the same basic process as on the terminal, except that you are using the Explore (Windows Explorer) utility to cut and paste. 1. Open ActiveSync > Explore. 2. Navigate to the program. 3.
System Tab The System tab enables you to verify and sometimes alter system parameters. To access the System tab, go to Start > Settings > System tab. Tap the appropriate icon to open that system setting. About The About system setting displays specific information about what is loaded on the terminal. It contains three tabs: Version tab Displays the information about the software, operating system, and processor of the terminal.
Device ID Displays the information the device uses to identify itself to other computers. It can be important to know this information if the Dolphin terminal is going to be part of a networked system of devices. The name or description can be changed according to the parameters on the screen. The first time this screen is opened, it displays the system’s default name and description for the device. The Device name is the name used for ActiveSync connection.
To change the default, select Low Speed and tap OK. A message appear confirming the changed and now current CPU speed. Tap OK to save the change. HHP WLAN Settings This option appears on the Settings tab only if an 802.11b radio is installed on the device. For more information, see The Status Icon on page 7-10. IrDA Config This system setting allows you to verify the IrDA port settings. Always displays the current status of the IrDA port. Enabled is the default.
Memory The Memory system setting enables you to review and manage both RAM (volatile) and IPSM/Storage Card (non-volatile) memory. Access this system setting whenever you receive system messages about memory. There are three tabs: Main, Storage Card, and Running Programs. Main tab This tab displays current capacity and usage of the 64MB of on-board, volatile RAM memory. This is the memory used for running and storing programs as well as storing program data.
Storage Card tab IPSM This tab displays the current capacity and usage statistics of the selected memory type; IPSM or Storage Card. Select the memory type from the drop-down list. IPSM is selected automatically. Total storage card memory The total MB of memory capacity of the selected memory. In use The MB currently being used. Free The MB that is still available for use. Short for Intel Persistent Storage Manager, this is14MB of on-board Flash memory that is nonvolatile.
Running Programs tab Displays the software programs currently using Storage memory. Check this tab when you are receiving out of memory errors or when the mobile computer is running slowly. You can • Select a program in the list and tap Stop to stop it from running (and therefore from using memory), or • Tap Stop All to automatically stop all running programs. ! Anytime you stop a running program, it frees up RAM memory.
Power The Power system setting enables you to check the remaining charge of both the main and backup batteries. For more information, see Batteries on page 3-10. You can also set automatic turn-off times for the terminal to conserve power. When the device is “turned off,” that means that it goes into suspend mode. For more information on suspend mode, see Suspend Mode on page 2-12. Radio Manager The Radio Manager enables you to see which radios are powered up on the Dolphin terminal.
The Region tab displays an overview of the region selected in the drop-down list at the top. The terminal is loaded with a number of pre-programmed regional settings. Select one from the list.
The results appear below. To see specific settings or change a specific setting, tap on one of the tabs, make the change and tap OK to save it. Remove Programs The Remove Programs settings enables you to remove programs installed on the terminal. Use this setting to troubleshoot when you receive messages that the device is out of memory. The programs removed are removed from RAM memory. Any program (usually *.cab or *.
To Remove Programs: 1. Tap Remove Programs. In the list, select the program you want to remove. 2. Tap Remove. The following message appears: 3. Tap Yes. Wait while the program is removed. 4. Verify that the program no longer appears in the list. Memory The Remove Programs screen displays the total storage memory available. It adjusts automatically when a program is removed for quick reference. For more detailed memory information, tap memory of “Adjust memory allocation.” along the bottom margin.
Screen The Screen setting enables you to re-align the screen at any time. You would need to re-align the screen if tapping buttons or icons with the stylus no longer seems to work appropriately. To align the screen, tap Align Screen, and follow the instructions. See Align the Screen on page 2-8. ClearType Dolphin 9500/9550 displays support ClearType font rendering. ClearType is a Microsoft technology that dramatically increases the readability of text on LCD displays.
Connection Settings The Connections tab serves as a connections manager for the terminal that enables you to manage your network connections. There are three main components: Beam Enables you to verify and adjust the infrared settings of the IrDA port. For details, see Using Infrared on page 6-5. Connections Enables you to configure your network connections for internet and work, create new connections, and set default connections. Network Adapters Enables you to configure your network adapters.
Connections Tab The Connections screen enables you to manage internet, work, and network card connections that the terminal defaults to when connecting to the network. When connecting to the internet, the system defaults to the setting selected here. The terminal is initially set to Internet Settings. When connecting to the internet, the system defaults to the setting selected here. The terminal is initially set to Work Settings. The network card connects to the setting selected here.
To Configure Internet Settings 1. On the Connections tab, select Internet Settings in the first drop-down list, and tap Modify. The Internet Settings screen appears displaying the Modem tab. The list in the middle of the screen displays existing internet connections. If you have not yet established an internet connection, “New…” appears in the list. 2. Tap New. The Make a New Connection screen appears. 3. Complete the fields. • • • • 5 - 18 Enter a name for the connection in the first field.
4. Tap Next to enter the phone number for the modem to dial. 5. Enter the phone number and tap Next. 6. Enter the parameters, including any extra dial-string modem commands, and tap Finish. You are returned to the Internet Settings screen where the new connection name and number appear in the list. You can tap on it any time to edit the settings.
Port Settings Advanced settings opens to this tab window. On it, enter the parameters for the port the terminal is using. Connection preferences Data Bits • Can be set between 4 and 8 Parity • Can be set to None, Odd, Even, Mark, or Space Stop Bits • Can be set to 1, 1.5, or 2 Flow Control • Can be set to Software, Hardware, or None Terminal settings Use terminal before connecting Use terminal after connecting Enter dialing commands manually Tap OK to save settings.
Name Servers settings Tap on this tab to determine how the terminal connects to servers. Server-assigned IP addresses use DHCP. You can • Use the server-assigned IP address (recommended) OR • Enter a specific server address in the fields provided: • DNS and Alt DNS - enter the domain name server address to locate the appropriate domain. If the domain can’t be found, the Alt DNS is tried automatically.
VPN Tab 1. After the Modem settings have been established, tap on the VPN tab. The Work Settings screen displays with a list of connections in the middle of the window. If no connections have been established, only New... appears. 2. Tap New to make a new connection. 3. Enter a name for the connection and type the desired IP address. Tap Advanced. The system processes the information and the TCP/IP and Name Servers tabs appear. • • See TCP/IP tab on page 5-20 for information about completing this tab.
5. Tap OK again and you are returned to the Work Settings screen, which now lists the new VPN connection. Proxy Settings Proxy setting are most often used when your terminal is connected to a network with a firewall. In this case, you would connect to the internet via a proxy server. To Connect Via Proxy Server 1. Open Work Settings and tap the Proxy Server tab. 2. Check the first box, then check This network uses a proxy server to connect to the Internet. 3.
• Socks and Port - if your network uses the circuit-level proxy server. If you enter an address here, the Type field activates and you need to select Socks 4 or Socks. • The User ID and Password fields activate after you have entered the appropriate information. If the fields activate, you need to complete both. 5. Tap OK to save and you are returned to the Proxy Server tab. 6. Tap OK again and you are returned to the Work Settings screen, which now lists the new Proxy Server connection.
Internet Settings On the Connections tab, in the first field (for Internet Settings), select New in the drop-down list. The General tab opens so that you can name the connection. Tap the Modem tab. The Modem tab opens. From there, complete the rest of the process for internet settings. For more information, see Internet Settings on page 5-17. You also have the option of tapping the Proxy Settings tab to have this connection go through a proxy server. For more information, see Proxy Settings on page 5-23.
Connecting You can test your connection settings on the Connections tab (see page 5-17) any time. In either of the first two drop-down lists (Internet and Work), select the desired setting. Tap Connect and the terminal begins connecting to the network. Note: The Connect button is active only when the selected connection setting is valid.
Network Card Connections The third field on the Connections tab (see page 5-17) enables you to select the connection setting of your network card. You can have your network card use your internet or work settings. Tap OK to save settings.
Network Adapters On the Connections tab (see page 5-17), tapping Network Adapters enables you to review the adapters installed on the terminal and the properties associated with each. To see the IP addresses and Name Servers of a network adapter, select one in the list, and tap Properties. Server-assigned IP addresses use DHCP.
Editing Properties Any time you open properties and tap OK, the system saves the settings. The following message appears after you tap OK: Tap OK again to save any changes.
5 - 30 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
6 Communications Overview You can exchange information between your Dolphin 9500/9550 and other mobile devices, a desktop computer, a network, or the Internet. You have the following connection options: • Connect to your desktop computer and synchronize via Microsoft ActiveSync v3.7 or higher. • Use the infrared (IrDA) port to send and receive files between two devices. • Connect to your Internet Service Provider (ISP).
Using ActiveSync Using Microsoft ActiveSync version 3.7 or higher, you can synchronize information on your desktop computer with your device and vice versa. Synchronization compares the data on the Dolphin mobile computer with your desktop computer and updates both with the most recent data. For example, you can: • Update the information in Microsoft Pocket Outlook® on your device by synchronizing it with Microsoft Outlook on your desktop computer.
Synchronizing from Your Device ActiveSync must be setup on your desktop computer and the first synchronization process completed before you initiate synchronization from your device. To initiate synchronization from your device, tap Start, then ActiveSync to begin the process. View connection status. Tap to connect and synchronize. Tap to stop synchronization. View synchronization status. Tap to synchronize via IR or change synchronization settings.
If the File is Not an Installer: 5. An error message appears stating that the program is valid but designed for a different type of computer. You need to manually transfer this file to the terminal. 6. If you cannot find any installation instructions for the program in the Read Me file or documentation, open ActiveSync and click Explore.* 7. Navigate to the My Pocket PC folder and copy the program file or files to the Program Files folder on the terminal.
Using Infrared Dolphin 9500/9550 terminals contains infrared or IrDA ports on the left side panel (see IrDA Port on page 3-8). Using these ports, you can send and receive data between the terminal and other devices equipped with infrared. This can include, but is not limited to, Pocket PC information such as Contacts and Tasks, as well as software upgrades. Verify That the IrDA Port is Enabled The IrDA port must be enabled to transmit data.
Verify That Beam Settings Are Set to Receive The Beam Settings must be set to receive for the terminal to receive data from other infrared devices. To verify, tap Start > Settings > Connections tab > Beam. The Beam Settings window should appear as follows: Sending and Receiving Information Sending: 1. Align the IR ports so that they are unobstructed and within a close range. 2. Open the program where you created the item you want to send and locate the item in the list.
Troubleshooting If the Beam Settings are not set to receive or you’ve aligned two IrDA ports and the terminal is still not receiving, go to Start > Programs > Infrared Receive. The terminal searches for the sending device.
Using an ISP The communication software for creating an ISP connection is already installed on your device. Your service provider should provide the software needed to install other services, such as paging and fax services. After you are connected, you can send and receive e-mail messages by using Inbox and view Web or WAP pages by using Pocket Internet Explorer. For more information, see Inbox on page 10-12. You can also download software applications from the web.
7 Wireless LAN Communications with 802.11b Overview Dolphin 9500/9550 terminals are available with an on-board 2.4 GHz 802.11b (Wireless Local Area Network) WLAN radio that uses Direct Sequence Spread Spectrum (DSSS) technology to spread the signal continuously over a wide frequency band. It provides a data rate of up to 11 Mbps. In addition, the open software architecture makes the Dolphin 9500/9550 a complete solution for a variety of wireless mobile data collection applications.
Configuring the 802.11b Radio Dolphin 9500/9550 terminal loaded with an 802.11b radio contain a configuration utility that enables you to enter and save the optimal transmission settings. Accessing the Configuration Utility You can access the configuration utility two ways: 1. Tap Start > Settings > System tab > HHP WLAN Settings . This icon appears on the System tab only if there is an 802.11b radio installed on the terminal. 2. Tap the Status icon - see The Status Icon on page 7-10.
Disable/Enable Radio Rescan Renew IP More Info Tap this button to toggle to disable/enable the radio link from the card. Tap this button to start a rescan process to search for an AP with a stronger signal in the network. Tap this button to reapply IP the address from the DHCP server when automatic DHCP is enabled. Tap this button to display detailed TCP/IP info; as shown in the following screen: Ping Tap this button to open the Ping utility for WLAN.
Field Description Timeout (ms) Displays the current timeout; 500 is the default. Increase or decrease it by tapping the up and down arrow buttons. Clear Tap this button to clear IP Address input and the ping statistics field. Ping Tap this button to ping the IP address entered in the input field. Ping Statistics field: Shows the pinging IP address and the pinging results. Config Tab The Config tab provides a list of all access points and peer stations in range.
Column This column displays… SSID The Network Name of the access point or peer station. An icon with signal strength Channel is also shown. The channel it uses and the WEP method it applies, if any. The icon stands for WEP Key-On, and SupRate for WEP Key-Off. Supported data rate of the access point or the peer station. BSSID (MAC Addr) BSSID or MAC Address of the access point or the peer station. Apply Refresh Tap Apply to associate your station with the SSID you selected.
Preferred Profile Icons You can complete a number of tasks to manage your Preferred Profiles using the five icons at the top of the window: Icon Name Tap this icon to… New Create a profile. Edit Modify a profile. Delete Delete a selected profile. Up Move the highlighted profile up to increase the automatic association priority. Down Move the highlighted profile down to decrease the automatic association priority. To Create a New Profile 1.
To Modify a Profile Select one and tap the Edit icon. The following screen displays: SSID Type TX Rate Chan WEP Parameters Use Manual Key WEP Method To enter an SSID, which is the Network Name. Check with your network administrator for Network Name (SSID). Choose Peer-to-Peer or Access Point from the drop-down list. Peer-to-Peer mode is used for communication between two (or more) radio stations (cards) without an access point. Access Point mode is also called “Infrastructure” mode.
To Delete a Profile Profiles may be deleted either from the Preferred List or from the Preferred List and Registry. To delete a profile, select (highlight) a profile and tap the Delete button and the following screen displays: From the pop-up window select the option of your choice and tap Yes to confirm or No to cancel.
Advanced Tab On the Settings window, tap the Advanced tab. The following screen displays: Power Save Mode Disable Always Enable Auto Enable Choosing this option disables the Power Save mode. Choosing this option makes the Power Save mode always enabled. This is the default setting. Choosing this option means that the Power Save mode is automatically enabled when the internal battery powers the terminal and automatically disabled when an external power supply powers the terminal.
About Tab This window provides Version Number and time of build for Network Driver, Configuration Utility, and NIC Firmware. On the Settings window, tap the About tab. The Status Icon You access the 801.11b configuration utility by tapping and holding on the Status icon screen. However, you must activate this icon before it appears. in the task tray at the bottom of the To Activate the Status Icon 1. Tap Start > Programs. 2. Tap the HHP WLAN Settings icon .
The Status Icon Menu When you tap the Status icon in the bottom tray, the following menu displays: Menu Option Selecting This Option… Wireless Radio On Turns on the radio. LED is on and the Link Icon displays with signal strength. Wireless Radio Off Turns off the radio. A pop-up window will ask for your confirmation. If confirmed, the LED will be off and the Status icon will change color from green to red on the top without signal strength displayed. The WLAN card/module will stop functioning.
Wireless Security Supplement AEGIS Client® offers the most comprehensive IEEE 802.1X supplicant for securing wired and wireless networks. The Client is a standards-based implementation of IEEE 802.1X and can be configured to work with almost any network equipment - wired or wireless - that supports the 802.1X authentication standard. The Client is interoperable with 802.1X-capable wireless access points and authentication servers including Microsoft's IAS and Cisco's ACS.
MD5 Worksheet To configure AEGIS Client to use MD5 authentication, you need to know: 1. Will you use your Windows user name and password for network authentication? (Applies only to Windows clients.) 2. If not, what is your unique user name/password combination? If a second set of credentials is required, you need to know the exact user name and password. These are typically casesensitive.
TTLS Worksheet To configure with TTLS authentication, you need to know: 1. Use Windows user name and password for authentication? (Applies only to Windows clients.) 2. If not, what is your unique user name? If a second set of credentials is required, you need to know the exact user name. This is usually case-sensitive. User name:_______________________________________ 3. Is a client certificate required? ____ No. ____ Yes. This file needs to be installed on your machine by your network administrator. 4.
PEAP Worksheet To configure AEGIS Client with PEAP Authentication, you need to know: 1. Use Windows user name and password for authentication? (Applies only to Windows clients.) 2. If not, what is your unique user name? If a second set of credentials is required, you need to know the exact user name. This is usually case-sensitive. User name:_______________________________________ 3. Is a client certificate required? ____ No. ____ Yes.
Configuring the Pocket PC Client Because AEGIS Client enables your terminal to access a network that is protected by the IEEE 802.1X protocol, you must configure EAP data communication to match your network server parameters. If the EAP configuration doesn’t match your network configuration, you can’t access the network. 1. On the terminal, open the client by going to Start > Programs > Meetinghouse AEGIS Client.
• • • In the Identity field, enter your network login or user name. In the Password field, enter your network password. If your network requires client certificates, select the Use certificate option and complete the information. • If the Authentication Type is PEAP or TTLS, select the Tunneled authentication option and enter the appropriate Identity, Password, and Protocol. 4. For most installations, you would skip the System tab, which controls system logging of network problems.
Port Status Icon Table Icon Color This color icon indicates that … Orange The port is associated, but there is no response to 802.11b packets. Blue There is no 802.11b activity. Green Authentication succeeded. Yellow Authentication is in process. Red Authentication failed. Configuring the AEGIS Client Software Configuration takes place at several levels: • First, each interface that interacts with the AEGIS Client may need to be configured.
User Settings Tab The User settings tab defines the protocol and the credentials used to authenticate a user. Identity The 802.1X identity supplied to the authenticator. The identity value can be up to 63 ASCII characters and is case-sensitive. In TTLS and PEAP, it is recommended that this field not contain a true identity, but instead the identity “anonymous”, and any desired realm (e.g. anonymous@myrealm.com). Password The password used for MD5-Challenge or LEAP authentication.
System Settings Tab The System Settings tab controls logging and the port manger timeout period. Log Level Port Manager Timeout 7 - 20 These settings control the detail of the log messages generated by the AEGIS Client. By default, all errors, warnings, and information events are logged. Each entry records a severity code (of one [debug message] to four [error] asterisks), a time stamp, and a message. Logs fill memory quickly, especially if the Debugging level is chosen.
Server Identity Tab The Server identity tab defines the credentials the client uses to authenticate the server during TLS/TTLS/PEAP authentication message exchange. AEGIS Client uses the information entered on this screen to verify that the Client is communicating with a trusted server. Do not validate server certificate chain When the server certificate is received during the TLS/TTLS/PEAP message exchange, it is not validated.
Port Setting Menus To see or manage the wireless cards or Ethernet NICs controlled by the Client, go to Start > Programs > Meetinghouse AEGIS Client. The Main menu contains a list of wireless and NIC adapters (ports). Tapping a port brings up a menu that allows the port to be enabled or disabled, configured, or deleted. Two menus are available from this screen: the Port menu and the Client menu. Port Menu To open the Port menu, tap and hold on a port on the main screen.
Client Menu To open the client menu, tap Client in the command bar along the bottom of the window. Close Start/Stop Restart Configure Install Protocol Exit Closes the Client's interface, while leaving the client running. Starts or stops 802.1X authentication. Same as a Stop followed by Start. Opens the Configuration screen displaying the User tab. Selecting this option binds the 802.1X protocol to the WLAN adapter currently installed on the device. The WLAN adapter then appears in the port list.
Port Setting Parameters Port settings parameters rarely need to be modified from their defaults. In most cases, you should modify these settings only if advised to by technical support. Port Settings are global to all ports. To open the Port Settings screen, select any adapter in the port list, tap and hold, then select Configure on the Port menu. The Port Settings screen is displayed. Protocol Settings These are the timer intervals and retry settings defined in the 802.
Certificate Management During configuration, you may have specified one or two certificates to use during the authentication process. The specified identity should match the Issued to field in the certificate and should be registered on the authentication server (i.e., RADIUS server) that is used by the authenticator. In addition, your certificate must be valid on the authentication server.
7 - 26 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
8 Wireless PAN Communications with Bluetooth Overview Dolphin 9500/9550 terminals are available with a Bluetooth radio for (Wireless Personal Area Network) WPAN usage. When the mobile computer is first initialized, the *.cab file and module for Bluetooth are installed. Powering Up the Bluetooth Radio Driver Before using the radio, make sure that the Bluetooth radio is powered up. When the radio driver is powered up, the Bluetooth icon appears in the task tray on the Today screen.
Assign COM Ports Follow these steps to view and/or modify the Bluetooth COM ports. If you are not going to use the IrDA port, you can disable it to free up a port for Bluetooth devices; see IrDA Config on page 5-7. 1. Tap on the Bluetooth icon on the Today screen. Select Advanced Features then My Bluetooth Device. Note: If you installed OBEX, the menu also lists Transfer via Bluetooth. 2. The My Bluetooth Device screen appears. Tap on the COM Ports tab. 3.
Discover Bluetooth Device(s) Follow these steps to discover other Bluetooth devices nearby, including non-phone devices. The Device Discovery Wizard is a more detailed alternative to using the Bluetooth “Get Connected!” Wizard or Bluetooth ActiveSync or Bluetooth LAN Access options. The Device Discovery Wizard allows you to discover any type of Bluetooth device. 1. If not open, launch the Bluetooth Devices folder. Tap on the Bluetooth icon on the Today screen.
2. Tap and hold your stylus on the Bluetooth device you want to bond with. In the pop-up menu, select Bond. 3. Alternatively, after selecting a device, tap on the Bond icon. Or tap on Device, then select Bond. 4. The Bluetooth Device Bonding Wizard launches. Follow the wizard to bond with your selected device.
5. As prompted, make sure the Bluetooth device that you want to bond with is in Bondable mode. 6. If the remote device is set up to accept bonding, a Bluetooth Passkey screen appears. To continue bonding, enter the correct passkey and tap Reply. 7. When you have successfully bonded with the other device, tap Finish. View Device Properties Follow these steps to view the properties of an already discovered device. 1. If not open, launch the Bluetooth Devices folder.
3. Use the General and Services screens to research device properties. If needed, assign a new device type icon by tapping on the arrow buttons in the General screen. You can also use the Device name field to rename the device. When done, tap OK for the setting to take effect. Set Up Your Favorite Device Follow these steps to set up default devices in the Bluetooth Devices folder. Please note that the Get Connected! Wizard automatically assigns the favorite phone. Complete these steps: 1.
2. In the pop-up menu, choose between Large Icons or Details. Large Icons Details Note: In Details view, you can see the Device Class and scroll right to see the current Bonded status. Delete a Device From the Folder If you no longer plan to connect with it, you can delete a device from the Bluetooth Devices folder. 1. If not open, launch the Bluetooth Devices folder. 2. Tap and hold your stylus on the device you wish to delete. In the pop-up menu, select Delete. 3.
Turn Radio Transmitter ON/OFF You may want to turn off the radio transmitter to save power or if you are entering an area with radio restrictions (e.g., an airplane). 1. The Bluetooth icon should appear in the task tray on the Today screen. Tap on the icon. 2. In the pop-up menu, select Turn Transmitter OFF. 3. The Bluetooth Card radio transmitter shuts off. The Bluetooth icon in the task tray becomes gray, as well as relevant menu options (e.g., Get Connected!). 4.
Bluetooth ActiveSync This section explains how to use the Bluetooth ActiveSync feature. It helps you quickly and easily ActiveSync to a notebook or desktop computer with ActiveSync v3.x installed. 1. Tap on the Bluetooth icon. In the pop-up menu, select Bluetooth ActiveSync. 2. The next screens varies depending on if your Bluetooth Devices folder contains any computers, and if one is chosen as your favorite.
(c) After a successful connection is made, the status screen reports Connected. Now you are ready to synchronize files, if desired. SCENARIO #3: Your Bluetooth Devices folder contains no computers. (a) When you tap on Bluetooth ActiveSync, a Bluetooth Device Search automatically begins. Note: You can also start the device search by tapping Find in the Bluetooth Devices screen. (b) After the search is complete, select the computer you wish to ActiveSync with and tap Select.
Bluetooth LAN Access This section explains how to use the Bluetooth LAN Access feature to quickly and easily connect to a Bluetooth-enabled LAN access point. 1. Tap on the Bluetooth icon. In the pop-up menu, select Bluetooth LAN Access. 2. The next screens varies depending on if your Bluetooth Devices folder contains any access points, and if one is chosen as your favorite. Please refer to the appropriate scenario: SCENARIO #1: Your Bluetooth Devices folder contains no favorite access point.
(a) When you tap Bluetooth LAN Access, your mobile computer automatically tries to connect with your favorite access point. (b) If your LAN requires a passkey, a screen appears, asking for the passkey. Enter the passkey, then tap OK. (c) After a successful connection is made, the status screen reports Connected. (d) Now you are ready to access your LAN for Internet access, files, etc. SCENARIO #3: Your Bluetooth Devices folder has no access points.
(e) After a successful connection is made, the screen reports Connected. (f) Now you are ready to access your LAN for Internet access, files, etc.
OBEX This section explains how to use the OBEX (object exchange) application to trade business cards, contacts or files with another Bluetooth device that supports OBEX. Bluetooth OBEX application supports five operations: • Exchange Business Cards • Send a Contact • Send a File • Browse Remote Device • Receive Contact or File • Enable File Sharing The first four operations - exchange business cards, send a contact, send a file, and browse remote device - are client-oriented.
2. Make sure the other Bluetooth device is set up to receive a contact. The device must support the OBEX Object Push profile. Note: If the other device is also using the Bluetooth Connection Kit, you can set it up to receive a contact by tapping the Bluetooth icon. In the pop-up menu, tap Transfer via Bluetooth > Receive Contact or File. 3. Now you are ready to exchange business cards. Tap on the Bluetooth icon. In the pop-up menu, tap Transfer via Bluetooth > Exchange Business Cards. 4.
3. Tap and hold your stylus on the contact(s) you would like to send. In the pop-up menu, select Send Via Bluetooth. 4. If your mobile computer has no devices in the Bluetooth Devices Folder, then it begins to search for Bluetooth devices nearby. 5. Select the Bluetooth device you wish to send the contact(s) to. If the desired device is not listed, tap Find. 6. Your mobile computer processes and send the contact(s). Send a File 1. Make sure the other Bluetooth device is set up to receive a file.
2. Now you are ready to send a file. Tap on the Bluetooth icon. In the pop-up menu, tap Transfer via Bluetooth > Send a File. 3. If your mobile computer has no devices in the Bluetooth Devices Folder, then it begins to search for Bluetooth devices nearby. 4. Select the Bluetooth device you wish to send a file. If the desired device is not listed, tap Find. 5. In the next screen, tap on the file you wish to send. You can use the Folder and Type drop-down menus to search for your file.
6. Your mobile computer sends the file. Browse Remote Device The Bluetooth File Explorer lets your mobile computer share files with another Bluetooth device. The other device must support the OBEX File Transfer server profile.
4. Select the Bluetooth device you wish to browse. If the desired device is not listed, tap Find. 5. Your mobile computer begins to establish a file sharing connection. 6. After the devices successfully connect, the Bluetooth File Explorer appears. Half of the screen shows contents of the remote device, while the other half shows contents of your device (the local device). The very bottom of the screen reports the connection status.
1. Select the file(s) or folder(s) that you wish to transfer. You can select items from only one device per transfer session. 2. There are two different ways to initiate the transfer: • Tap on the File menu. Select Send to remote or Get from remote, as applicable. The inappropriate option should be gray. • Tap on the Send to remote icon or Get from remote icon, as applicable. The inappropriate icon should be gray. 3. A screen reports the status of the transfer. 4.
3. In the next screen, enter a name for your new folder. Tap OK. 4. The new folder should be listed under the appropriate device. Delete File(s) or Folder(s) 1. Select item(s) that you wish to delete. You can only delete item(s) from one device at a time. 2. Tap on the File menu. Select Remote device or Local device, wherever the item(s) are located, then tap Delete remote item(s) or Delete local item(s), as applicable. 3.
2. Start the connection process by either of two methods: • • Tap on the Device menu. Select Connect. Tap on the Connect icon. 3. In the next screen, select the device you wish to connect to. Tap Select. Your mobile computer attempts to connect to the device selected. To disconnect from the remote device, do the following: 1. Start the disconnection process by either of two methods: • • Tap on the Device menu. Select Disconnect. Tap on the Connect icon. 2.
2. The Enable File Sharing status screen appears. Your mobile computer waits two minutes for the remote device to connect. 3. After successfully connecting to the remote device, the screen report Connected. 4. If two minutes passes before you connect, tap Wait Again. 5. File sharing is enabled until you end it by tapping Cancel.
Using the Dialer This section explains how to assign a dialing prefix and use the Dialer to dial a number directly from your Contacts list. The Dialer makes it quick and easy to perform dial-up networking. Note: The Dialer has been verified to work with Nokia and Ericcson phones and is known not to work with the Motorola 270c, NTT Docomo Paldio 633S or Sony au C413S phone. Results may vary with other phones that are not listed as being supported by the Bluetooth system.
4. If you have multiple phone numbers for a contact, a screen appears listing them, including any dialing prefix you may have assigned. Select the phone number you wish to dial. 5. Your mobile computer connects to your phone and begins dialing. The Dialer can dial a phone number containing any of the following non-numeric characters: * # + . / ! @ - \ space A B C D T P W The following string can also be included in a phone number: (',') The Dialer cannot dial a phone number containing non
Get Connected Wizard The Get Connected! Wizard guides you through a one-time setup process that prepares the mobile computer and phone for Bluetooth connections. The wizard varies depending on what phone you want to connect to. Ericsson, Nokia 6210, NTT DoCoMo, Sony Phones 1. Tap on the Bluetooth task tray icon. In the pop-up menu, select Get Connected! 2. Follow the Bluetooth “Get Connected!” Wizard. In the second screen, use the drop-down list to select your Bluetooth phone.
4. When the search is complete, a list of the discovered Bluetooth phones appears. Choose the phone you wish to connect to, and tap Select. A service discovery phase begins, about 5-10 seconds. 5. As prompted in the next screen, prepare your phone for bonding. For instructions on setting your phone to “Bondable” or “Pairable” mode, refer to your phone manual. Have your passkey ready, then tap Next>. 6. In the next screen, enter the passkey. Tap Reply. 7.
4. The mobile computer begins to search for the phone. When the search is over, a list of the discovered Bluetooth phones appears. Choose the phone you wish to connect to, and tap Select. A service discovery phase begins, about 5-10 seconds. 5. The next two screens describe procedures you can only complete outside of the wizard. Read through each screen but do not complete the described procedures until you exit the wizard.
Dial-up to Your Network Complete the following steps to create a new Bluetooth internet connection. Before setting up dial-up networking, prepare yourself with dial-up information and other necessary settings from your office network or ISP. 1. Go to Start > Settings > Connections tab > Connections. In the top field, select Internet Settings and tap Modify. Then, tap New. 2. On the Make a New Connection screen, enter a name for the dial-up connection. For the modem, select Bluetooth Phone.
5. Uncheck Wait for dial tone before dialing. Tap Finish. 6. Now you are ready to start the connection. In the Connections screen, under Internet Settings, tap Connect. In Network Log On, verify the dialing settings. Tap OK. If you want to configure Port Settings, TCP/IP, or Name Server settings, navigate to the setting and tap Advanced; see Advanced Settings on page 5-19. 7.
• Scroll to Automatic, then press SELECT. Press DONE. Automatic Connections for Nokia 3650/7650: • On the phone, press MENU. • Scroll to Connectivity, then press OPTIONS. • The Open option should be highlighted. Press SELECT. • The Bluetooth option should be highlighted. Press OPTIONS. • The Open option should be highlighted. Press SELECT. • Scroll to the right tab to access the Paired devices list. Highlight your mobile computer, then press OPTIONS. • Scroll to Set as authorized, then press SELECT.
8 - 32 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
9 Wireless WAN Communications with GSM/GPRS Overview Dolphin 9500 terminals can be configured with Wireless Wide Area Network (WWAN) via an integrated Siemens® GSM/GPRS tri-band radio module. Note: Dolphin 9550 mobile computers with pistol-grip do NOT support GSM/GPRS. GSM - GSM stands for Global System for Mobile communications. It is an open, non-proprietary wireless wide area networking system that is constantly evolving and growing.
SIM Card Installation SIM stands for Subscriber Information Module. A SIM card stores the subscriber's personal information, GSM/GPRS radio settings, security key, contacts, etc. SIM cards can be installed and removed from any mobile device, enabling you to switch devices without losing your personal information. SIM cards are obtained and activated by the network provider that supports the GSM/GPRS network. On the Dolphin 9500 terminal, the SIM card door is located in the battery well on the back panel.
Using uPhone The uPhone Application Suite contains three programs that function together to provide a complete voice, data, and text messaging solution for a mobile device fitted with a radio modem: • Call Log enables you to view and manipulate a list of the most recent calls. • Dialler emulates a mobile phone and is used to make and receive telephone calls. • SMS Manager provides a text message handler similar to many email programs. Accessing uPhone Go to Start > Programs > uPhone.
Bubble Dialogs If the Dialler or SMS Manager are not visible, the following bubble dialogs appear automatically: Incoming Call Displayed when an incoming call is received and the Dialler is not visible. The caller’s name or number displays if it is in your Phonebook. “No number" displays if the caller’s ID is not available. The ringtone is played while the phone is ringing. • Tap Answer to answer the call and open the Dialler. Tapping Answer also places a current call on hold.
Using the Dialler To launch the Dialler, tap Start > Programs > uPhone > Dialler. The program launches and the uPhone Dialler screen opens: Dialler screen Information lines 1. Network Operator - name of service provider. 2. Number/Name - number and/or name of dialed, incoming, and outgoing calls 3. Status - displays the status of the phone. Signal Strength Four bars is optimal for transmission.
When the call is connected, the three information lines display the following: Joe Smith Network Operator Name/Number Status Displays the name of the service provider you are using. Displays the name and/or number you called. If the number is from your Phonebook, that entry displays. The status of the call. Idle means no calls are incoming or outgoing, In Call means a phone call is in progress, Incoming Call means that a a call is coming in.
Touchtones To transmit touchtones for interactive voice systems while in a call, you can • Tap the 0-9, *, and # buttons on the uPhone Dialler screen. • Press 0-9 keys on the Dolphin keyboard; use the uPhone Dialler screen buttons for * and #. Volume Control Use the Dolphin keyboard to manually adjust the volume.
You can access the Phonebook manually by opening the Dialler and going to Tools > Phonebook. When you tap and hold on an entry, a popup menu displays the following options: Dial Opens the Dialler with the number entered ready for dialing. Send SMS Opens the SMS Manager in the Compose screen with the 'To:' field populated with the number. Settings Menu The Settings menu provides the following options: Speakerphone Toggles speakerphone mode on and off.
Audio Modes The back panel of the Dolphin 9500 contains both a speaker and a microphone that you can use to send and receive audio signals over the GSM network. For details about the microphone and speaker on the back panel of the Dolphin 9500, see Back Panel Features on page 3-4. There are three audio modes: 1. Handset 2. Headset 3.
Ringtone Configuration Different ringtones, with individual volume settings, can be set for the following: Ring Tone Sounds on an incoming call. Message Tone Sounds on an incoming SMS or Voicemail notification. Call Waiting Tone Sounds to indicate an incoming call while you are already on a voice call. Accessing Ringtone Configuration You can access Ringtones two ways: 1. Go to Start > Settings > Personal tab > Ringtones icon OR 2.
Call Log The Call Log maintains a list of the last 20 calls made or received in each of the following categories: • Voice Calls In • Voice Calls Out • Voice Calls Missed Voice Call In is the default display whenever the Call Log is opened. Opening the Call Log You can access the Call Log two ways: 1. Go to Start > Programs > uPhone > Call Log) OR 2. Open the Dialler (go to Tools > Call Log). The Call Log opens displaying the last few Voice Calls In; the most recent call always appears at the top.
Call Log Options Voice Calls Out and Voice Calls Missed are available from the drop-down list. Select the option you want to view. To see everything, select All Calls. Tools Menu The Tools menu in the Call Log provides you with the following options: Select this menu option To… Clear Delete the entire Call Log. Exit Close the Call Log.
SMS Manager Abbreviated for Short Message Service, SMS enables the transmission of short messages (140-160 characters) to and from a cell phone. SMS messages travel over the system's control channel, which is separate from the voice channel. The SMS Manager on the Dolphin 9500 supports creation, sending, receiving, and storing of SMS text messages. Text messages sent or received can be up to 160 characters long. Opening the SMS Manager You can access the SMS Manager two ways: 1.
When the folder is selected, the messages in it appear in the list. The name of the folder appears in the gray bar just under the title bar. To Open a message Delete a message Do this… Tap on it in the list. Tap and hold on it in the list. A popup menu appears that enables you to delete the message. Sending an SMS Message 1. In the task tray at the bottom of the screen, tap New. The new message screen opens with the cursor active in the text area. 2. Tap inside the To: field.
• You must type a number that is in the appropriate international ISDN format for the country you are dialing. However, you can dial a local number without the country code. • Destination numbers can start with a “+” sign. 3. Tap inside the text area. To write a message, you can use the SIP or the keyboard. The Remaining characters field displays how many characters you can type. It counts backwards from 160 as you type each character. 4. When finished typing, tap the Send icon to transmit the message .
GPRS Settings After subscribing to a GPRS network and installing your SIM card, you can load the parameters of your GPRS subscription into the terminal. However, some subscriptions load automatically when you install your SIM card. If the GPRS settings do not load automatically, you must enter them manually. uPhone includes a pre-configured GPRS connection in Internet Settings. You need to select or create GPRS settings prior to making a GPRS call for the first time.
To Add a GPRS Setting 1. On the GPRS Settings screen, in the Current Profile drop-down list, select Add new. 2. Type in the Profile Name, APN, IP Address, and select the Protocol. 3. Tap OK. You return to the settings screen. The Profile Name you selected now appears in the Current Profiles list. GPRS Connection When a GPRS connection is required - e.g., by navigating to a web site - a Network Log On screen is automatically displayed. Enter the Password and Domain, then tap OK to connect.
You have the option of disconnecting by tapping on the GPRS connection icon in the navigation bar and tapping End.
Establishing GPRS Internet Settings Because GSM/GPRS technology uses a network connection, you need to configure Internet Settings or Work Settings to use GPRS parameters in the Connection Manager. Note: Make sure that you are not using ActiveSync when configuring the connection settings. Note: Please note that the following instructions are a generic overview. To establish a GPRS connection, you need to review the information from your network service provider.
2. Select Internet Settings and tap Modify. The Internet Settings screen appears displaying the current internet setting for GPRS on the Modem tab. 3. Tap New. The Make a New Connection screen appears. 4. Enter a name for the connection; something that indicates that this is the GPRS connection is recommended. 5. Select a modem from the drop-down list. 6. Select a Baud rate from the drop-down lists; 57600 is recommended for optimal performance.
7. Tap Next. Another screen appears asking for the exact phone number. 8. This information is available only from the network service provider you are using for GPRS. “#99*” is the generic dialing number for GPRS. Enter the number and tap Next.
9. Enter the information and tap Finish. You are returned to the Internet Settings screen with the connection you just established displaying in the list.
10 Applications Microsoft Pocket Outlook includes Calendar, Contacts, Tasks, Inbox, and Notes. You can use these programs individually or together. For example, e-mail addresses stored in Contacts can be used to address e-mail messages in Inbox. Using Microsoft ActiveSync, you can synchronize information in Microsoft Outlook or Microsoft® Exchange Server on your desktop computer with your device. You can also synchronize this information directly with a Microsoft Exchange server.
3. Using the input panel, enter a description and a location. Tap first to select the field. Tap to return to the calendar (the appointment is saved automatically). Tap to choose from predefined text. Tap to choose from previously entered locations. Tap to select a time. Tap to select a date. Notes is a good place for maps and directions. Entering an Appointment 4. If needed, tap the date and time to change them. 5. Enter other desired information. To see all available fields, hide the input panel. 6.
Using the Summary Screen When you tap an appointment in Calendar, a summary screen is displayed. To change the appointment, tap Edit. View appointment details. View. Tap to change appointment. Appointment Summary Screen Creating Meeting Requests You can use Calendar to set up meetings with users of Outlook or Pocket Outlook. The meeting request is created automatically and sent either when you synchronize Inbox or when you connect to your e-mail server.
Contacts Contacts maintains a list of your friends and colleagues so that you can easily find the information you’re looking for, whether you’re at home or on the road. Using the device infrared (IR) port, you can quickly share Contacts information with other device users. Select the category of contacts you want displayed in the list. Tap and enter part of a name to quickly find it in the list. Tap to see additional phone numbers and e-mail addresses. Tap to display or edit the contact details.
To Create a Contact 1. Tap New. Tap to return to the contact list (the contact is saved automatically). Scroll to see more fields. Notes is a good place for maps and directions. Creating a Contact 2. Using the input panel, enter a name and other contact information. You need to scroll down to see all available fields. 3. To assign the contact to a category, scroll to and tap Categories and select a category from the list. In the contact list, you can display contacts by category. 4.
Using the Summary Screen When you tap a contact in the contact list, a summary screen is displayed. To change the contact information, tap Edit. View contact details. Tap to view notes. Tap to change contact information.
Tasks Use Tasks to keep track of what you have to do. Select the category of tasks you want displayed in the list. Select the sort order of the list. Indicates high priority. Tap to display or edit the task details. Tap and hold to display a pop-up menu of actions. Tap to create a new task. Task Application Note: To change the way information is displayed in the list, tap Tools > Options.
To Create a Task 1. Tap New. Tap to return to the task list (the task is saved automatically). Tap to choose from predefined subjects. Notes is a good place for maps and drawings. Creating a Task 2. Using the input panel, enter a description. 3. You can enter a start date and due date or enter other information by first tapping the field. If the input panel is open, you need to hide it to see all available fields. 4. To assign the task to a category, tap Categories and select a category from the list.
Using the Summary Screen en you tap a task in the task list, a summary screen is displayed. To change the task, tap Edit. View task details. Tap to show and hide additional summary information. View notes. Tap to change task.
Notes Quickly capture thoughts, reminders, ideas, drawings, and phone numbers with Notes. You can create a written note or a recording. You can also include a recording in a note. If a note is open when you create the recording, it will be included in the note as an icon. If the note list is displayed, it will be created as a stand-alone recording. Tap to change the sort order of the list. Tap to open a note or play a recording. Tap and hold to display a pop-up menu of actions. Tap to record.
To Create a Note 1. Tap New. 2. Create your note by writing, drawing, typing, and recording. For more information about using the input panel, writing and drawing on the screen, and creating recordings, see Using the Dolphin 9500/9550 Mobile Computer on page 4-1. Tap to return to the note list (the note is saved automatically). Tap to show or hide the input panel. Tap to write on the screen. Tap to add a recording to the note.
Inbox Use Inbox to send and receive e-mail messages in either of these ways: • Synchronize e-mail messages with Microsoft Exchange or Microsoft Outlook on your desktop computer. • Send and receive e-mail messages by connecting directly to an e-mail server through an Internet service provider (ISP) or a network. Synchronizing E-mail Messages E-mail messages can be synchronized as part of the general synchronization process. You need to enable Inbox synchronization in ActiveSync.
Using the Message List Messages you receive are displayed in the message list. By default, the most recently received messages are displayed first in the list. Select the service and folder you want to display. Select the sort order for messages. Tap to open a message. Tap and hold to display a pop-up menu of actions. Tap to connect and to send and receive e-mail. Tap to connect to the selected service.
When you receive a message, tap it to open it. Unread messages are displayed in bold. Tap to return to the message list. Tap to delete this message. Tap to view the previous or next message. Tap to reply to or forward this message. Viewing A Message When you connect to your e-mail server or synchronize with your desktop computer, by default, you’ll receive messages from the last five days only, the first 100 lines of each new message, and file attachments of less than 100 KB in size.
Composing Messages 1. Tap New. 2. In the To field, enter an e-mail or SMS address of one or more recipients, separating them with a semicolon, or select a name from the contact list by tapping the Address Book button. All e-mail addresses entered in the e-mail fields in Contacts appear in the Address Book. Tap to send the message. Tap to show or hide the complete header. Tap to show / hide the recording toolbar. Tap to display the Address Book. Tap to insert common messages.
Folder Behavior with a Direct Connection to an E-mail Server The behavior of the folders you create depends on whether you are using ActiveSync, SMS, POP3, or IMAP4. • If you use ActiveSync, e-mail messages in the Inbox folder in Outlook will automatically be synchronized with your device. You can select to synchronize additional folders by designating them for ActiveSync. The folders you create and the messages you move will then be mirrored on the server.
Pocket Internet Explorer Use Microsoft Pocket Internet Explorer to view Web or WAP pages in either of these ways: • During synchronization with your desktop computer, download your favorite links and mobile favorites that are stored in the Mobile Favorites subfolder in Internet Explorer on the desktop computer. • Connect to an Internet service provider (ISP) or network and browse the Web. When connected to an ISP or network, you can also download files and programs from the Internet or intranet.
The Mobile Favorites Folder Purpose The Mobile Favorites folder was created on your desktop computer when you installed ActiveSync. It enables you to create Favorite Links on your desktop computer that you can transfer to your Dolphin 9500/9550 terminal. Those Favorite Links are then available for selection when browsing the internet on your terminal. Process First, you create your Favorite Links in the Mobile Favorites folder on your desktop computer.
View Mobile Favorites and Channels on the Terminal 1. Access Pocket Internet Explorer. 2. Tap the Favorites button to display your list of favorites . Tap the favorite you want to view. Tap to add or delete a folder or favorite link. 3. Tap the page you want to view. You’ll see the page that was downloaded the last time you synchronized with your desktop computer. If the page is not on your device, the favorite will be dimmed.
3. Tap the AvantGo Channels link. 4. Tap Activate. 5. Follow the directions on the screen. You will need to synchronize your device with your desktop computer and then tap the My Channels button to complete the AvantGo setup. When synchronization is complete, tap the AvantGo Channels link in your list of favorites to see a few of the most popular channels. To add or remove channels, tap the Add or Remove link.
Companion Programs The companion programs for Pocket PC installed on Dolphin 9500/9550 terminals are • Pocket Word and • Pocket Excel. Windows® Media Player™ for Pocket PC, Microsoft® Money, MSN® Messenger, Microsoft® Reader are NOT installed on the Dolphin 9500/9550 when shipped but may be installed from the Microsoft Companion CD. Pocket Word Pocket Word works with Microsoft Word on your desktop computer to give you easy access to copies of your documents.
If you’re opening a Word document created on a desktop computer, select Wrap to Window on the View menu so that you can see the entire document. Typing Mode Using the input panel or Dolphin keypad, enter typed text into the document. For more information on entering typed text, see Using the Dolphin 9500/9550 Mobile Computer on page 4-1. To format existing text and to edit text, first select the text.
Writing Mode In writing mode, use your stylus to write directly on the screen. Ruled lines are displayed as a guide, and the zoom magnification is greater than in typing mode to allow you to write more easily. For more information on writing and selecting writing, see Using the Dolphin 9500/9550 Mobile Computer on page 4-1. Writing on the Screen in Pocket Word With Space button selected, drag to insert space. An arrow appears showing the space direction and size. Tap to highlight selected text.
Drawing Mode In drawing mode, use your stylus to draw on the screen. Gridlines appear as a guide. When you lift your stylus off the screen after the first stroke, you’ll see a drawing box indicating the boundaries of the drawing. Every subsequent stroke within or touching the drawing box becomes part of the drawing. Select Shape on the pop-up menu to convert objects to proper shapes. Resize an object by dragging the selection handles. Tap an arrow to see your choices.
Pocket Excel Pocket Excel works with Microsoft Excel on your desktop computer to give you easy access to copies of your workbooks. You can create new workbooks on your device, or you can copy workbooks from your desktop computer to your device. Synchronize workbooks between your desktop computer and your device so that you have the most up-to-date content in both locations. Use Pocket Excel to create workbooks, such as expense reports and mileage logs.
10 - 26 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
11 Dolphin 9500/9550 HomeBase Overview As the hub of your Dolphin 9500/9550 system, the Dolphin HomeBase charging and communication cradle supports both RS232 and USB communications, which make it able to interface with the majority of PC-based enterprise systems. When a terminal is seated in the HomeBase, its main battery pack charges in less that four hours.
Dolphin 9500/9550 HomeBase Parts and Functions Front Panel Terminal Well Auxiliary Battery Well DOC K AUX BATT ERY COM M DOCK LED AUX Battery LED COMM LED Terminal Well Place the Dolphin terminal in this well both to communicate with a host device. If the host device is a desktop computer that uses ActiveSync, synchronization begins immediately. While seated in the terminal well, the main battery installed in the terminal charges.
For information about charging a battery in the auxiliary battery well, see page 11-7. COMM LED This is the communication LED. It indicates the status of data transfer between the Dolphin terminal and the host device. The color of this LED differs if the HomeBase is using the serial or USB port connection. If using the serial port: This color means… Red Serial data is being sent from the Host Device to the Dolphin HomeBase. Green Serial data is being sent from the Dolphin HomeBase to the Host Device.
Rear Panel Auxiliary Battery Well USB Port RS-232 Port DC Power Jack Auxiliary Battery Well The HomeBase enables you to charge an additional Li-ion battery pack independently of the terminal well. This feature ensures that you can always have a fully-charged battery for your Dolphin terminal. See Powering the HomeBase on page 11-6. USB Port This USB Port is full-speed and 2.0 compliant. Using a USB cable, you can connect the HomeBase to a peripheral device, such as a desktop computer or printer.
HomeBase Serial Connector The following diagram displays the serial connector of the HomeBase. Note: Signals referenced are for a DTE device. The Home Base is at a right-angle to the printed circuit board (PCB). The ninth pin has a ring indicator (RI).
Powering the HomeBase The terminal requires 9.5 Volts DC input for communications and battery charging; the HHP power cable converts the power source voltage accordingly. 1. Connect the HHP power cable to the DC jack on the rear of the HomeBase. 2. Connect the HHP power cable to the power source. HHP recommends that you leave the Dolphin HomeBase connected to its power source at all times, so that it is always ready to use.
Charging the Main Battery The Dolphin HomeBase powers the terminal and fully charges its main battery pack in less that four hours. The HomeBase contains an intelligent battery charging system that protects the battery from being damaged by overcharging; the unit senses when a battery pack is fully charged and automatically switches to maintain the battery at full capacity indefinitely.
Communications Communications Types RS-232 The HomeBase supports RS-232 communications via the RS-232 Communications Port located on the back of the device. Tis port enables the Dolphin terminal to communicate to a personal computer, modem, or any RS-232 device using a standard serial cable and communications software. USB The HomeBase also supports USB communications via the USB port located on the back.
Setting up the Terminal The Dolphin terminal may be configured for communications using the ActiveSync options as described in Chapter 2 or manually as described below. To set Communications Properties, complete these steps: 1. Select Start > ActiveSync > Tools > Options. 2. Select the PC tab. 3. Check the Enable synchronization box and select the desired option from the pull-down list; 115200 Default is recommended for an RS-232 connection. 4. Tap OK. 5. Place the Dolphin in the cradle.
The following graphic displays the correct ActiveSync Connection Settings on the desktop computer for an RS-232 connection. Note: You can have the USB connection box checked in addition to the serial cable box without affecting processing. However, you would most likely use one or the other. Setting up the HomeBase for USB Communication The Dolphin 9500/9550 terminal is defaulted to support USB communications out of the box. Required Equipment: • HomeBase with power supply • USB Cable • ActiveSync v3.
Setting up the Terminal To select ActiveSync options: 1. Select Start > ActiveSync > Tools > Options. 2. Select the PC tab. 3. Check the Enable synchronization box and select ‘USB Connection from the drop-down list. 4. Tap OK. 5. Place the Dolphin in the cradle. The Dolphin 9500/9550 attempts to start an ActiveSync connection with the desktop computer automatically.
The ActiveSync Connection Settings must be set as the following graphic indicates. The Allow USB connection with this desktop computer box must be checked. Do not check the serial cable box. Communicating with the Dolphin 9500/9550 Terminal To initiate communications between the Dolphin 9500/9550 and its peripheral, complete these steps: 1. Insert the Dolphin 9500/9550 into the terminal well of the HomeBase. • The DOCK LED illuminates green.
Mounting the HomeBase Set the Dolphin HomeBase on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal while it is in the HomeBase.
Wall Mounting The following diagram displays how to wall-mount a Homebase: 1. Secure screws to 2. Attach the 3. Fasten the 4. Turn the secured the bottom panel by sliding them into the available slots bottom panel to the mounting bracket - match the holes to the secured screws screws to secure the HomeBase to the mounting bracket HomeBase right side up. 5. Using the appropriate screws, secure the mounting bracket to the wall or vertical surface as shown.
12 Dolphin 9500/9550 Mobile Base Overview The Dolphin Mobile Base charging and communication cradle is designed specifically for in-premise and in-transit data collection applications. It features a flexible mounting bracket, a cigarette lighter adapter, and a power cable to adapt it to your environment. When a terminal is seated in the Mobile Base, its main battery pack charges in less than four hours.
Mobile Base Parts and Functions Front Panel The front panel of the Mobile Base has one slot. The following graphic features the Mobile Base with the Dolphin 9500 inserted into the Terminal Well. Terminal Well Mounting Brackets DO CK COM M DOCK LED Terminal Well Mounting Brackets DOCK LED COMM LED 12 - 2 COMM LED Place the terminal in this well to communicate with a host device and charge the main battery pack. Use these to mount the Mobile Base to a fixed location.
Bottom Panel The power supply and RS-232 connectors are located on the bottom of the unit. Power Supply Connector RS-232 Communications Port Power Supply Connector Use this connector to attach an HHP power cable to the Dolphin 9500/9550 Mobile Base. The Mobile Base can be powered by an external DC power source of between 11 VDC to 48 VDC. The optional HHP cigarette lighter adapter cable allows the Mobile Base to be powered from a standard 12 VDC cigarette lighter outlet in a vehicle.
Powering the Dolphin Terminal When seated in a Mobile Base that is connected to the appropriate power source, the Dolphin terminal receives the power to charge its main battery and run its internal circuitry. Keep the Mobile Base plugged into the power source so that the Dolphin terminal battery pack stays fully charged. For more information about powering the Mobile Base, see Powering the Dolphin Mobile Base on page 12-6.
Installing the Dolphin Mobile Base To install the Dolphin Mobile Base, you need to mount it securely to an appropriate location and supply it with power. Mounting the Mobile Base The adjustable mounting bracket holds the terminal securely in place and gives the user a variety of options for mounting the Mobile Base. When selecting a location, keep in mind that the power supply and serial connectors point straight out the bottom panel.
Locking Tabs When positioned as shown in the above graphic, the locking tabs secure the spring arm assembly, latch, and terminal in place. When seating a terminal, turn both arms up to allow the spring arm to move as necessary while the terminal is being inserted. After the terminal is seated, turn both arms toward the center to lock them. Spring Arm Assembly The spring arm assemble is the column that connect the latch to the back of the Mobile Base.
Setting the Mobile Base Up for Communications The Mobile Base RS-232 interface allows the Dolphin terminal to communicate to a personal computer, modem, or any standard RS-232 device using a standard serial cable and communications software. Connecting the Cables Connect the Mobile Base to the host computer or other device by plugging an RS-232 serial cable into the RS-232 Communications Port on the bottom of the Mobile Base.
Mobile Base Serial Connector The following diagram displays the serial connector of the Mobile Base. Note: Signals referenced are for a DTE device. The Mobile Base connector is straight to the printed circuit board (PCB). The ninth pin sends 500mA at 5V power out. This can power a peripheral device, such as a mobile printer, provided that that peripheral device can accept 500mA at 5V.
4. Select the appropriate baud rate for connecting to the RS-232 Host Device; ‘11520 is the default. 5. Tap OK and close the ActiveSync window on the Dolphin 9500/9550 terminal. 6. Place the Dolphin in the Mobile Base. Synchronization begins immediately.
12 - 10 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
13 Dolphin 9500/9550 ChargeBase Overview The Dolphin ChargeBase is a four-slot charging cradle that can charge four Dolphin terminals, each in less than four hours. provides intelligent battery charging for Dolphin 9500/9550 terminals with Li-ion battery packs installed. Capacity The ChargeBase can hold up to four Dolphin 9500/9550 terminals. Each charging slot works independently to control the charging of each terminal.
Dolphin ChargeBase Parts and Functions Front Panel Terminal Wells Dock LED Charge LED Terminal Wells The ChargeBase contains four terminals wells. Each well • Holds and charges the main battery pack of one Dolphin 9500/9550 terminal. • Contains the companion to the industrial-grade, 17-pin connector on the bottom panel of Dolphin 9500/9550 terminals. • Has two LEDs on the front: the Dock LED and the Charge LED.
Power Supply The ChargeBase includes a power supply that contains a power adapter to ensure the proper voltage. The power adapter is plugged into standard AC/DC outlets. Power Adapter Power Connector Cable ON/OFF Switch Power Cord ON Position Supplying Power to the ChargeBase ! Using a non-HHP power adapter voids your warranty and could result in serious damage to the circuitry of the Dolphin ChargeBase. 1. Be sure the power switch on the power adapter is in the OFF position. 2.
Inserting and Removing Terminals Inserting 1. Hold the terminal with the bottom panel perpendicular to the base. DOL PH I N 9 5 00 POWE R SC A N E SC SF T VOL + PG A B 4 F 7 2 C 5 G J - : R U Y 6 END D H 9 *S P F3 T F6 V INS Z CTRL L , O F2 F5 STA RT SEN D K N F1 3 0 M Q PG 8 I ; E NT VO L 1 E @ + TA B NU M F4 F7 W BK SP SP F8 X DEL ALT 2. Slide the terminal into the well until the Dock LED lights solid green. 3. Charging begins immediately.
Charging Terminals in the ChargeBase The Dolphin ChargeBase charges the main battery of each terminal in less than four hours. The ChargeBase uses the intelligent battery charging system incorporated into all Dolphin terminals that prevents overcharging. This means that Dolphin terminals may be stored in the ChargeBase indefinitely without damage to the terminals, battery packs, or the ChargeBase. 1. Power the ChargeBase; see Supplying Power to the ChargeBase on page 13-3. 2.
Mounting the ChargeBase The Dolphin ChargeBase should be on a dry, stable surface. To easily adapt the ChargeBase to your environment, it can be mounted on a flat, horizontal surface such as a desktop or workbench, or a flat, vertical surface such as a wall. When choosing a location, always bear in mind that • The mounting location must allow users easy access to the power connector. • The ChargeBase should be oriented so that users can easily read the labels.
2. Turn the ChargeBase and DIN Rail right side up. 3. Secure the DIN Rail to a stable, flat horizontal surface.
Using the Mounting Brackets Use the screws and the mounting brackets to mount the ChargeBase to a wall or other vertical surface. The wall mount kit contains two mounting brackets to secure both ends of the ChargeBase. Each mounting bracket contains an open slot in the back to accomodate the connector cables. 1. Secure the screws into the four screw slots on the bottom panel. Insert the heads into the round end and slide towards the narrow end until the screw is secure. Screws in slots 2.
3. Using the nuts and bolts, secure the mounting brackets to the bottom panel. 4. Secure the mounting brackets to an appropriate horizontal surface.
13 - 10 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
14 Dolphin 9500/9550 QuadCharger Overview The Dolphin QuadCharger is a four-slot charging station that provides intelligent battery management for Dolphin 9500/9550 battery packs. It can charge each battery in less than four hours. The fourth slot features a battery analyzer that completely resets and re-calibrates a battery and displays its resulting capacity. Compatibility The QuadCharger is compatible with the Li-ion batteries that power the Dolphin 9500 series of mobile computing devices.
Charge/Analyze Slot This is the fourth slot and the only one that can be used to charge or analyze a battery. When a battery is placed in this slot, it begins charging just as it does in the other three slots. However, if you press the ANALYZE button, it runs the battery in the slot through the complete Analyze cycle. For more information, see Using the Battery Analyzer on page 14-4. Battery Capacity Indicator LEDS Indicates the progress of the Analyze cycle of the battery in the Charge/Analyze slot.
Supplying Power to the QuadCharger The charger must be connected to the appropriate power source for any type of operation. 1. Locate the AC power cord that came with the Dolphin QuadCharger. 2. Plug the cord into the power supply connector on the back of the unit and then plug the power cord into a wall socket. 3. Press the power switch to the ON position. The power LED illuminates green, and the charger performs a self-diagnostic test that lasts approximately five seconds.
Using the Battery Analyzer Location The battery analyzer is located in the fourth slot of the ChargeBase. Only batteries in this slot can be analyzed. Analyze Cycle The Analyze cycle is initiated when a battery is placed in the Charge/Analyze slot and the ANALYZE button is pressed. In an Analyze cycle, batteries are completely discharged, then recharged to capacity, as well as completely reset and re-calibrated.
Mounting the QuadCharger The Dolphin QuadCharger should be on a dry, stable surface. To easily adapt the QuadCharger to your environment, it can be mounted on a flat, horizontal surface such as a desktop or workbench, or a flat, vertical surface such as a wall.
Wall Mounting The following graphic displays how mount a QuadCharger to a wall: Troubleshooting If you encounter problems with your Dolphin QuadCharger, refer to chart below for possible solutions. If problems persist, please contact HHP Technical Support. Problem Issue The Status LED does not come on when I insert a battery pack into the Dolphin QuadCharger Check the power connections on the Dolphin QuadCharger; make sure the POWER switch is ON and the battery pack is properly seated.
15 Warranty, Support, and Service Limited Warranty Hand Held Products, Inc., d/b/a HHP (“HHP“) warrants its products to be free from defects in materials and workmanship and to conform to HHP’s published specifications applicable to the products purchased at the time of shipment.
Return Information Should your unit or any of the peripherals prove to be defective within the stated warranty period from the date of purchase, return the product, as described in the Repair Maintenance Authorization (RMA) procedures below, and we will, at our option, repair or replace the product, to whatever extent HHP deems necessary to restore the product to proper operating condition, without any charge to you. You must obtain an RMA number to receive service from any of HHP’s repair facilities.
Technical Assistance If you have a question or problem with your unit, you can obtain technical assistance from HHP’s Application Support department. North America/Canada: Telephone: Fax number: E-mail: (800) 782-4263, Option 4 (8 a.m. to 6 p.m. EST) (315) 685-4960 support@HHP.com Europe, Middle East, and Africa: Telephone European Ofc: +31 (0) 40 29 01 600 U.K. Ofc: +44 1925 240055 E-mail: euro_support@HHP.com Asia: Telephone: E-mail: +852-2511-3050 asia_support@HHP.
15 - 4 Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
A Appendix A - Keyboards Overview This appendix provides useful tools for programming and managing your Dolphin 9500/9550 terminal. General Windows Keyboard Shortcuts Use the keyboard shortcuts in the chart below to navigate the Dolphin 9500 and Dolphin 9550 terminal keyboards. These are standard keyboard shortcuts for Windows applications.
43-Key Alpha/Numeric Keyboard Blue Key Functions and Characters The following table displays the special functions performed and characters inserted using the blue key. Key Combination Function/Special Character Blue key + D - (minus) Blue key + H _ (underscore) Blue key + L = Blue key + P + Blue key + Q ; Blue key + R : Blue key + S * Blue key + T / Blue key + U @ Blue key + X \ Blue key + Y START Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft A-2
Red Key Functions and Characters The following table displays the special functions performed and characters inserted using the red key.
Key Combinations Using Blue + Sft Keys Key/Key Combinations Function/Special Characters SFT + Blue + T ? SFT + Blue + X > Miscellaneous Key Combinations A-4 Key/Key Combinations Function/Special Characters NUM + ALT + 3 + 9 ‘ NUM + ALT + 3 + 4 “ Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft
35 Key Numeric/Alpha Keyboard Blue Key Functions and Characters Key Combination Function/Special Character Blue key + . + Blue key + , - Blue key + F1 ; Blue key + F2 : Blue key + F3 / Blue key + F4 \ Blue key + SP + Blue key + DEL - Dolphin® 9500/9550 Mobile Computer User’s Guide - GSM Draft A-5
Key Combinations Use the key combinations listed below to access certain keyboard functions or to use special characters that are not defined on the 35-key version of the Dolphin keyboard.
56 Key Full Alpha Numeric Blue Key Functions and Characters Key Combination Function/Special Character Blue key + .
Key Combination Function/Special Character Red key + E F5 Red key + F F6 Red key + G F7 Red key + H F8 Red key + I F9 Red key + J F10 Red key + K F11 Red key + L F12 Red key + M F13 Red key + N F14 Red key + O F15 Red key + P F16 Red key + Q F17 Red key + R F18 Red key + S F19 Red key + T F20 Red key + U F21 Red key + V F22 Red key + W F23 Red key + X F24 Red key + Y Z * Exit the mouse utility prior to adjusting the contrast.
Key Combinations Use the key combinations listed below to access certain keyboard functions or to use special characters that are not defined on the 56-key version of the Dolphin keyboard. SFT Key Combinations Key Combination Function/Special Character SFT + 1 ! SFT + 2 @ SFT + 3 # SFT + 4 $ SFT + 5 % SFT + 6 ^ SFT + 7 & SFT + 8 * SFT + 9 ( SFT + 0 ) SFT + .
Com Port Assignment Table Com Port Assignment Com Port 1 Serial port. This is the 17-pin connector on the bottom panel of Dolphin 9500/9550 terminals. Com Port 2 Bluetooth Module If there is no Bluetooth hardware installed on the terminal, this com port is unassigned. Com Port 3 Raw Infrared Com Port 4 Com Port 5 USB virtual serial port Com Port 6 IrDA, if IrDA is enabled. If IrDA is disabled, this com port becomes available. See To Disable the IrDA Port on page 5-7. Com Ports 7-9 Unassigned.
™ 95/9550/UG Rev (b)
