DRAFT COPY 11/11/11 Dolphin™ 7800 with Windows® Embedded Handheld 6.
DRAFT COPY 11/11/11 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
DRAFT COPY 11/11/11 Table of Contents Chapter 1 - Dolphin 7800 Terminal Agency Information Laser Safety .........................................................................................................................1-1 Label Locations ..............................................................................................................1-1 Model Number, Serial Number and IMEI Labels............................................................1-1 Laser Safety Label ...........................
DRAFT COPY 11/11/11 Accessories for the 7800 ..................................................................................................... 3-4 Front Panel: 7800 ................................................................................................................ 3-5 Front Panel Features for the 7800................................................................................. 3-6 Back Panel: 7800 ..........................................................................................
DRAFT COPY 11/11/11 Using the Navigation Keys .................................................................................................. 6-3 30-Key Numeric Keyboard .................................................................................................. 6-4 30-Key Numeric Keyboard Combinations...................................................................... 6-4 30-Key Numeric (Calculator) Keyboard ...............................................................................
DRAFT COPY 11/11/11 Installing Additional Software .............................................................................................. 8-8 Adding Programs Using ActiveSync or Windows Mobile Device Center ....................... 8-8 Connecting the Terminal to a Wireless Network.......................................................... 8-10 Adding Programs Using the Internet............................................................................ 8-10 Software Upgrades ..........................
DRAFT COPY 11/11/11 Communication Ports ........................................................................................................ 11-1 Selecting the Port ........................................................................................................ 11-1 COM7 .......................................................................................................................... 11-1 GPS Intermediate Driver.............................................................................
DRAFT COPY 11/11/11 Mounting ............................................................................................................................ 14-3 Safety Precautions....................................................................................................... 14-3 Installation.................................................................................................................... 14-4 Charging the Main Battery ..................................................................
DRAFT COPY 11/11/11 Limited Warranty ............................................................................................................... 18-3 How to Extend Your Warranty .....................................................................................
DRAFT COPY 11/11/11 x
1 DRAFT COPY 11/11/11 Dolphin 7800Terminal Agency Information Dolphin 7800 mobile computers meet or exceed the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Read these guidelines carefully before using your Dolphin terminal. This documentation is relevant for the following Dolphin models: 7800L0, 7800LW, 7800LG, 7800LC.
DRAFT COPY 11/11/11 LED Safety LED Safety Statement LEDs have been tested and classified as “EXEMPT RISK GROUP” to the Standard: IEC 62471:2006. ! CAUTION! Do not view directly with optical instruments. UL and C-UL Statement UL and C-UL listed: UL60950-1 2nd Edition, and CSA C22.2 No. 60950-1-07 2nd Edition. Approvals by Country Country EMC, Radio, & SAR Safety U.S.A. FCC Part 15, Subpart B FCC Part 15, Subpart C, 15.
DRAFT COPY 11/11/11 The equipment is intended for use throughout the European Community; PAN European Frequency Range: 2.402–2.480 GHz. Restrictions for use in France are as follows: • Indoor use: Maximum power (EIRP*) of 100 mW for the entire 2.400–2.4835 GHz • Outdoor use: Maximum power (EIRP*) of 100 mW for the 2.400–2.454 GHz band & maximum power (EIRP*) of 10 mW for the 2.454–2.483 MGHz band. • 5Ghz band: UNII (Unlicensed National Information Infrastructure) or band1 (5.150 to 5.
DRAFT COPY 11/11/11 Canadian Compliance This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. This Category II radiocommunication device complies with Industry Canada Standard RSS-310.
DRAFT COPY 11/11/11 For European Community Users Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE); European REACH Regulation 1907/2006 of 1 June, 2007, and Restriction of Hazardous Substances Directive (RoHS) 2002/95/EC of 1 July 2006. Waste Electrical and Electronic Equipment Information This product has required the extraction and use of natural resources for its production.
DRAFT COPY 11/11/11 Hearing Aid Compatibility (HAC) The Dolphin 7800 has been tested for hearing aid compatibility. This device has an M3 and T3 rating. For additional HAC information, including the HAC rating for this product, please refer to www.honeywellaidc.com. When some wireless devices are used near some hearing devices such as hearing aids and implants, users may detect a buzzing or humming noise. Some hearing devices are more immune than others to this interference noise.
2 DRAFT COPY 11/11/11 Getting Started Out of the Box Verify that the carton contains the following items: • Dolphin mobile computer (the terminal) • Main battery pack • Quick Start Guide If you ordered accessories for your terminals, verify that they are also included with the order. Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service. For details, see Product Service and Repair on page 18-1. Initial Setup for Dolphin 7800 Terminals Step 1.
DRAFT COPY 11/11/11 Step 3. Charge the Main and Backup Batteries The power supply for Dolphin terminals consists of two types of battery power: the main battery pack that is accessible from the back panel, and the backup battery that resides inside the terminal. The main battery powers the terminal. The internal backup battery charges off the main battery and maintains the application data stored in RAM memory for up to 5 minutes when the terminal’s main battery pack is completely discharged or removed.
DRAFT COPY 11/11/11 Host Device Communication Cable (7800-USBH, 7800-DEX) Use only a UL Listed power supply, which has been qualified by Honeywell with an output rated at 5VDC and 3A with the device. Dolphin 7800 4 1 Plug Adapter Cable Cup 5 Host Device 3 Power Cable 2 or COMM Cable USB DEX Battery Error Notification If your terminal displays the following indicators, replace the main battery pack with a Honeywell battery pack.
DRAFT COPY 11/11/11 Step 5. Set the Time Zone, Time, and Date On the Home screen, tap the line that displays the time and date. When the Clock & Alarms screen appears, tap the arrow to the right of the time zone to open the drop down menu. Select the appropiate time zone from the menu. Set the correct time and date in the remaining fields and tap OK to save. Replacing the Main Battery Pack Note: Before replacing the main battery pack, read the Guidelines for Battery Pack Use and Disposal on page 3-13.
DRAFT COPY 11/11/11 6. Insert the new battery and apply gentle pressure to engage the latch. Note: Make sure the stylus tether is not caught under the battery during installation. 7. Lock the battery by sliding the latch toward the battery pack. Note: The terminal does not power ON unless the battery is locked. 8. Reattach the hand strap. 9. Press the Power key or the SCAN key to wake the terminal from Suspend Mode (see page 2-11). ! We recommend use of Honeywell Li-ion battery packs.
DRAFT COPY 11/11/11 Icons in the Title Bar Indicator Meaning New voicemail New instant message Vibrate on Ringer off Speakerphone on Voice call in progress Calls are forwarded Call on hold Missed call Data call in progress A battery error has occurred. Replace the main battery pack with a Honeywell Li-ion battery pack.
DRAFT COPY 11/11/11 Icons in the Title Bar Indicator Meaning GPRS available GPRS connecting GPRS in use HSDPA available HSDPA connecting HSDPA in use EDGE available EDGE connecting EDGE in use UMTS available UMTS connecting UMTS in use Radio is off The radio is not connected to a network. The radio is connected. The bars indicate the signal strength. No radio signal The terminal is searching for a signal.
DRAFT COPY 11/11/11 Horizontal Scroll The Horizontal Scroll, located at the top of most application windows, provides access to additional application screens. You can flick left or right on the scroll or tap each label on the scroll, until you get to the desired screen. Tapping a label to the left or right of the center item brings new labels into view. Note: Tap the Title bar to access the horizontal scroll if it is not visible on the screen.
DRAFT COPY 11/11/11 File Explorer You can also use the File Explorer to find files and organize these files into folders. 1. Tap > File Explorer . 2. Tap the Up button at the bottom of the screen to move up one level in the directory. 3. You can move files in File Explorer by tapping and holding on the item you want to move, then tapping Cut or Copy on popup menu. 4. Navigate to the folder you want to move the file to, then tap and hold a blank area of the window. 5. Tap Paste on the pop-up menu.
DRAFT COPY 11/11/11 File Provisioning on the 7800 \IPSM\Honeywell The IPSM folder is the only partition on the 7800 that persists across a kernel upgrade (*.UPG file extension). During a kernel upgrade, files are automatically copied from the \IPSM\Honeywell\Autoinstall folder and then installed in the \Honeywell (root file system) folder as part of the upgrade process. \IPSM\Honeywell\AutoInstall The files in the IPSM\Honeywell\AutoInstall folder are only installed when a factory reset or kernel upgrade oc
DRAFT COPY 11/11/11 Resetting the Terminal There are three types of system resets: a soft reset, a hard reset, or a factory reset. The soft and hard resets preserve all data stored in the file system. Contact a Honeywell technical support representative for more information on how to perform a factory reset. Soft Reset (Warm Boot) A soft reset re-boots the device and preserves any objects created in RAM.
DRAFT COPY 11/11/11 2 - 12
3 DRAFT COPY 11/11/11 Hardware Overview Standard Configurations for the 7800 WLAN & WPAN • Microsoft Windows Embedded Handheld 6.5 Classic • 800MHz TI OMAP Processor • 256MB RAM X 512MB Flash • Six keyboard options • 3.7V Li-ion standard battery pack or extended rechargeable battery pack • Adaptus Imaging Technology: N5603ER/ SR/HD or N5600ER/SR/HD image engines • 802.11a/b/g/n and Bluetooth WLAN, WPAN, with GPS • Microsoft Windows Embedded Handheld 6.
DRAFT COPY 11/11/11 WLAN, WPAN, WWAN with GPS & Camera • Microsoft Windows Embedded Handheld 6.5 Professional • 800MHz TI OMAP Processor • 256MB RAM X 512MB Flash • Six keyboard options • 3.7V Li-ion extended rechargeable battery pack • Adaptus Imaging Technology: N5603ER/ SR/HD or N5600ER/SR/HD image engines • 802.11a/b/g/n, Bluetooth, and GSM/ HSPA+ • GPS • 3.0 megapixel auto control color camera WLAN, WPAN, & WWAN with GPS • Microsoft Windows Embedded Handheld 6.
DRAFT COPY 11/11/11 Peripherals for the 7800 Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal. Dolphin 7800 HomeBase™ Device The Dolphin 7800 HomeBase device is a charging and communication cradle equipped with a USB host port that is Hi-Speed 2.0v compliant, which enables the terminal to interface with the majority of PCbased enterprise systems.
DRAFT COPY 11/11/11 Accessories for the 7800 Each of the following items is sold separately to enhance your terminal’s capabilities. Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away from the body. Dolphin 7800 Mobile Charger The Dolphin 7800 Mobile Charger is a charging cable that connects the terminal directly to a 12 Volt DC power source, such as a cigarette lighter port inside a vehicle, eliminating the need for a cradle.
DRAFT COPY 11/11/11 Front Panel: 7800 Front Speaker Charge Indicator LED General Notification LED Touch Panel Display Volume Control Button Left Scan/Image Button Right Scan/Image Button SCAN Key Right Soft Key Left Soft Key Navigation Keys Power Key Send Call or End Call Microphone Blue Modifier Key Red Modifier Key I/O Connector Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all 7800 models unless otherwise indicated.
DRAFT COPY 11/11/11 Front Panel Features for the 7800 Blue Modifier Key See Using the Modifier Keys on page 6-3. Charge Indicator LED The light emitting diode (LED) located above the top left corner of the LCD display illuminates when the Power Tools BattMon application is enabled and the device is on AC charge. For more information, consult the Dolphin Power Tools User’s Guide for Windows Embedded Handheld 6.5. Front Speaker The front speaker is the receiver for handset voice calls.
DRAFT COPY 11/11/11 SCAN Key The SCAN key is centrally located for easy access with the right or left hand. When pressed, the SCAN key activates the scanner/imager. The SCAN key also functions as a system wakeup control for the terminal. Touch Panel Display The color 3.7 inch 64k color liquid crystal display (LCD) touch panel is covered with an industrial, protective lens for greater durability. The video graphic array (VGA) display resolution is 480 X 640.
DRAFT COPY 11/11/11 Back Panel: 7800 Image/Scan Engine Window* Stylus/Stylus Slot Hand Strap Hook Stylus Tether Rear Speaker Flashlight/Camera Flash Fastener for the Stylus Tether Battery Lock Color Camera Battery Release Button Battery Hand Strap Memory Card Socket and SIM Card Socket (located under protective shield) Battery Well Memory/SIM Shield Screws, Qty.
DRAFT COPY 11/11/11 Back Panel Features for the 7800 Battery Dolphin 7800 model terminals are designed for use with standard battery pack model 7800BTSC (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack models 7800-BTXC and 7800BTXCW (Li-ion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc. For information on how to remove the battery, see Replacing the Main Battery Pack on page 2-4.
DRAFT COPY 11/11/11 When the protective SIM/memory card cover and battery pack are properly installed, the cards are sealed against moisture and particle intrusion, read/write data is stored securely, and the terminal’s environmental rating is preserved; see Installing a SIM Card and/or Memory Card on page 3-16. Rear Speaker The integrated rear speaker sounds audio signals as you scan bar code labels and enter data.
DRAFT COPY 11/11/11 I/O Power Out The I/O connector also provides power out (to peripheral devices) +5V at 500mA. This means that, with the proper cable, the terminal can power another device. By default, power out is disabled, but the 5V output may be enabled, see Five Volt Control on page 7-12. Using the Touch Panel Honeywell defines proper use of the terminal touch panel as using a screen protector and proper stylus. Screen protectors maintain the ongoing integrity (i.e.
DRAFT COPY 11/11/11 Batteries There are two types of battery power: the main battery pack installed in the back panel and the backup battery located inside the terminal. They are designed to work together to prevent data loss when the terminal is in use over long periods. Both batteries must be completely charged before using a Dolphin terminal for the first time! Main Battery Pack ! We recommend use of Honeywell Li-ion battery packs.
DRAFT COPY 11/11/11 Storing Batteries To maintain top performance from batteries, avoid storing batteries outside of the following temperature ranges: • 14°F to 113°F (-10°C to +45°C) for short term storage of less than one month • 32°F to 86°F (-0°C to +30°C) for long term storage Do not store batteries in extremely high humidity. For prolonged storage, do not keep batteries stored in a charger that is connected to a power source.
DRAFT COPY 11/11/11 Internal Backup Battery Located inside the terminal is a 3.6 Volt nickel metal hydride (NiMH) backup battery. The backup battery prevents the terminal from being reset if you need to replace the main battery pack. It retains RAM data during the battery pack exchange. A fully charged backup battery provides 5 minutes of data backup time.
DRAFT COPY 11/11/11 MedState=25% This sets the Low Battery point to 25%. When the battery hits the percentage charge specified here, the user is notified. LowState=10% This sets the Critical Battery point to 10%. When the battery hits the percentage charge specified here, the user is notified. Note: Warnings do not appear when the terminal is on external power.
DRAFT COPY 11/11/11 Hardware Maintenance When needed, clean the image engine window and the LCD display with a clean, non-abrasive, lint-free cloth. The terminal can be cleaned with a damp cloth. For additional information on hardware maintenance specific to the Dolphin Healthcare Housings, see page 3-11. Installing a SIM Card and/or Memory Card SIM Card Short for Subscriber Information Module, a SIM card stores the subscriber's personal information, GSM/GPRS radio settings, security keys, contacts, etc.
DRAFT COPY 11/11/11 If you are not installing a memory card (i.e., microSD or MicroSDHD card), proceed to step 11. 7. Unlock the memory card latch by sliding the latch toward the top of the terminal. 8. Lift the latch to expose the memory socket. 9. Insert the MicroSD or MicroSDHC card. 7 8 9 10. Close and lock the memory card latch. 10a 10b 11. Insert the SIM card. Align the chamfered corner of the card with the chamfered corner of the socket. 12. Close and lock the SIM card latch.
DRAFT COPY 11/11/11 13. Reinstall the shield and screws to protect the sockets. 14. Install and lock the battery. The terminal automatically starts the power up sequence. Note: The terminal does not power ON unless the battery lock is engaged.
4 DRAFT COPY 11/11/11 Using the ScanImage Engine Overview The Dolphin terminal houses a compact image engine that instantly reads popular 1D and 2D bar codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The image engine can also capture black and white digital images, such as signatures and pictures of damaged inventory.
DRAFT COPY 11/11/11 Focus N5603/N5600 High Density (HD) Symbology Distance (in/cm) N5603/N5600 Standard Range (SR) N5603/N5600 Extended Range (ER) Delta (in/cm) Distance (in/cm) Distance (in/cm) Near Far Delta (in/cm) Near Far Delta (in/cm) Near Far 3 mil C39/128 2.0 (5.1) 3.4 (8.6) 1.4 (3.6) - - - - - - 5 mil C39/128 1.4 (3.6) 4.8 (12.2) 3.4 (8.6) 2.7 (6.9) 6.3 (16.0) 3.6 (9.1) 5.4 (13.7) 9.0 (22.9) 3.6 (9.1) 7.5 mil C39/128 1.4 (3.6) 5.6 (14.2) 4.2 (10.7) 2.5 (6.
DRAFT COPY 11/11/11 Supported Bar Code Symbologies Symbology Type Symbology Name 1D Symbologies Codabar Codablock F Code 3 of 9 Code 11 Code 32 Pharmaceutical (PARAF) Code 93 Code 128 EAN with Add-On EAN with Extended Coupon Code EAN-8 EAN-13 GS1-128 GS1 Databar Interleaved 2 or 5 ISBT 128 Matrix 2 of 5 MSI Plessey Aztec Codablock A Codablock F GS1 Databar MaxiCode Micro PDF Data Matrix PDF417 QR Code 2D Symbologies Composite Codes UPC/EAN UCC/EAN GS1 Databar OCR OCR US Money Font MICR (E 13 B)
DRAFT COPY 11/11/11 Decoding The terminal supports two types of image decoding for use in various bar code reading and imaging applications: full-area imaging and Advanced Linear Decoding (ALD). Full-Area Imaging Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR, signature capture, and picture taking. When reading all bar code types using full-area imaging, a positive read can be obtained from many positions; see Aiming Beam Options on page 4-5.
DRAFT COPY 11/11/11 Aiming Beam Options The aiming beams are smaller when the terminal is held closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit whereas symbologies with larger bars or elements (mil size) should be read farther from the unit. N5603 Red High-Vis Aiming Pattern If your Dolphin terminal is configured with a N5603 imager, high-vis aimers frame the bar code for more intuitive aiming.
DRAFT COPY 11/11/11 Capturing Images The image-capture process is an intuitive, split-second operation for experienced users. By following the basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to adapt it to different application environments. Image Preview When the imaging process is initiated, the touch screen displays a preview of the object. This is a live video image of what the imager is currently viewing.
DRAFT COPY 11/11/11 Enabling the Aimer You can enable the aiming pattern for imaging in the Imaging Demo. For details about the aimer, see Aiming Beam Options on page 4-5. 1. Tap > Demos > Imaging Demo > Setup menu > Aimer. 2. The aiming pattern is now enabled for imaging. Uploading Images Image files can be uploaded to a host workstation using Microsoft ActiveSync or Windows Mobile Device Center and a Dolphin communication peripheral.
DRAFT COPY 11/11/11 4-8
5 DRAFT COPY 11/11/11 Using the Color Camera Overview Dolphin 7800 terminals equipped with a 3.0-Megapixels Resolution color camera with Automated Camera Control (ACC), and an Application Programming Interface (API) provide easy integration of color picture and video capture into business applications. The camera lens and camera flash are located on the back panel of the terminal. Taking a picture using the Camera Demo tool 1. Tap > Demos > Camera Demo . 2.
DRAFT COPY 11/11/11 Options Tap Options > Camera. The Camera Options menu appears. There are five tabs of configurable options accessible from the Camera Options menu. Profile Tab Display Tab The profile tab allows you to customize your camera settings, or chose from several predefined profiles designed to provide the best picture quality for common tasks. Capture Tab Caption Tab File Tab Taking a picture using the Windows Embedded Handheld 6.5 Camera tool 1. Tap > Pictures & Videos > Camera 2.
DRAFT COPY 11/11/11 6. Tap OK on the Tile Bar to return to the active viewfinder screen. Menu Tap Menu on the Tile Bar at the bottom of the touch screen to adjust the camera settings, switch to video mode, and access additional camera options. Item Descriptions Video Activate Video Mode Mode Set Mode (i.e., Normal, Burst, or Timer) Resolution Set Picture Resolution (i.e., QVGA, VGA, SVGA, XGA, UXGA, or QXGA) Zoom Set Zoom (i.e.
DRAFT COPY 11/11/11 Uploading Pictures and Videos Piture and Video files can be uploaded to a host workstation using Microsoft ActiveSync or Windows Mobile Device Center and a Dolphin communication peripheral. For additional information see Connecting and Synchronizing the Terminal and Workstation on page 8-6.
6 DRAFT COPY 11/11/11 Using the Keyboards Available Keyboards Note: Contact a sales representative for information on additional keyboard options. 30-Key Numeric Keyboard 2 ESC 46-Key QWERTY Keyboard 3 ENT 30-Key Numeric (Calculator) Keyboard 46-Key AZERTY Keyboard A Q* 0 . 46-Key QWERTZ Keyboard F1 Q W E R T Z U I O A* S D F G H J K L X C V B N M Y 0 P . All Keyboards Contain the Following: • • • • Backlit for easy viewing in various lighting conditions.
DRAFT COPY 11/11/11 Keyboard Combinations See 30-Key Numeric Keyboard on page 6-4. See 30-Key Numeric (Calculator) Keyboard on page 6-6. See 46-Key QWERTY Keyboard on page 6-8. See 46-Key AZERTY Keyboard on page 6-11. See 46-Key QWERTZ Keyboard on page 6-14. Common Buttons See Using the Function Keys on page 6-2. See Using the Modifier Keys on page 6-3. See Using the Navigation Keys on page 6-3. Using the Function Keys Name Key Symbol Backlight or Function Turns the keyboard backlight on or off.
DRAFT COPY 11/11/11 Using the Modifier Keys Name Key Function Blue & Red Blue Red The blue and red keys are used in combination with other keys to type special characters and perform system functions. Each keyboard is color-coded to indicate the character typed or function performed when specific keys are pressed immediately after the blue or red modifier key. Normal Press the blue or red key once to modify only the next key pressed.
DRAFT COPY 11/11/11 Key Function & Moves the cursor up one page. Red Moves the cursor one character to the right. Moves the cursor one character to the left. Note: Additional functionality varies according to the application in use.
DRAFT COPY 11/11/11 Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Right Soft Key Right Soft Key performs right function.
DRAFT COPY 11/11/11 Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Period period asterisk asterisk period Blue Blue 0 0 0 0 F10 Red Red 30-Key Numeric (Calculator) Keyboard Up Navigation Key, Volume Up, Page Up Down Navigation Key, Volume Down, Page Down SCAN key Left Soft Key Right Soft Key Right Navigation key, Flashlight Left Navigation key, Backlight Power key, End Key Send key Tab key Space key Backspace, Delete key Escape key Enter key Shift key Blue key Red k
DRAFT COPY 11/11/11 Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Right Soft Key Right Soft Key SEND SEND Cold Boot Cold Boot SEND Left Left Backlight Left Left Up Volume Up Volume Up Volume Up Page Up Down Volume Down Volume Down Volume Down Page Down Right Right Right Right Flashlight POWER\EN D Power\End Warm Boot Warm Boot Power\End TAB TAB back TAB TAB TAB 7 7 @ or ? or ! @ or ? or ! F7 8 8 abc ABC F8 9 9 def DEF F9 Space Space D
DRAFT COPY 11/11/11 Key Normal Blue + Normal Blue + Normal + Shift Red + Normal Period period asterisk asterisk period Blue Blue 0 0 plus + 0 F10 Red Red 46-Key QWERTY Keyboard Up Navigation Key, Volume Up, Page Up Down Navigation Key, Volume Down, Page Down SCAN key Left Soft Key Right Soft Key Right Navigation key Left Navigation key Power key, End Key Send key Backspace, Delete key Shift key Enter key Tab key Blue key Escape key Red key Space\Symbol key Backlight\Flashlig
DRAFT COPY 11/11/11 Key Normal Shift + Normal Blue + Normal Red + Normal Left Soft Key Left Soft Key SCAN Scan Right Soft Key Right Soft Key Power/End Power/End Power/End Warm Boot Power/End Left Navigation Key Left Up Navigation Up Up Volume Up Page Up Down Navigation Down Down Volume Down Page Down Right Navigation Right Q q Q # (pound/group) F1 W w W 1 F2 E e E 2 F3 R r R 3 F4 T t T ( F5 Y y Y ) F6 U u U _ (underscore) F7 I i I - (minus
DRAFT COPY 11/11/11 Key Normal Shift + Normal Blue + Normal H h H : (colon) J j J ; (semi-colon) K k K ‘ (single quote) L l L “ (double quote) Backspace Backspace Backspace & (ampersand) Shift Shift Z z Z 7 X x X 8 C c C 9 V v V ? (question mark) B b B ! (exclamation point) N n N \ (back slash) M m M . (period) Comma , (comma) < , (comma) , (comma) ENT Enter TAB Tab Back Tab Back Tab Tab Period . (period) > 0 .
DRAFT COPY 11/11/11 46-Key AZERTY Keyboard Up Navigation Key, Volume Up, Page Up Down Navigation Key, Volume Down, Page Down SCAN key Left Soft Key Right Soft Key Right Navigation key Left Navigation key Power key, End Key Send key A Q* Backspace, Delete key Shift key Enter key 0 Tab key . Blue key Red key Space\Symbol key Escape key Backlight\Flashlight key 46-Key AZERTY Keyboard Combinations Key Normal Shift + Normal Blue + Normal Red + Normal Send Send Send Cold Boot Send Left
DRAFT COPY 11/11/11 Key Normal Shift + Normal Blue + Normal Red + Normal Left Navigation Key Left Up Navigation Up Up Volume Up Page Up Down Navigation Down Down Volume Down Page Down Right Navigation Right A a A # (number sign) F1 Z z Z 1 F2 E e E 2 F3 R r R 3 F4 T t T + (plus) F5 Y y Y _ (underscore) F6 U u U - (minus) F7 I i I = (equal) F8 O o O " (double quote) F9 P p P áü F10 Q q Q * (asterik) S s S 4 D d D 5 F f F 6
DRAFT COPY 11/11/11 Key Normal Shift + Normal Blue + Normal Red + Normal Backspace Backspace Backspace Shift Shift W w W 7 X x X 8 C c C 9 V v V % (percent) B b B & (ampersand) N n N ? (question mark) M m M ! (exclamation mark) Comma , (comma) < @ , (comma) ENT Enter TAB Tab Back Tab Back Tab Tab Period . (period) > 0 .
DRAFT COPY 11/11/11 46-Key QWERTZ Keyboard Up Navigation Key, Volume Up, Page Up Down Navigation Key, Volume Down, Page Down SCAN key Left Soft Key Right Soft Key Right Navigation key Left Navigation key Power key, End Key Send key F1 Q W E R A* S D F G Y X C Shift key 0 Tab key Z U I O H J K L V B N M T P Backspace, Delete key Enter key . Blue key Escape key Red key Space\Symbol key Backlight\Flashlight key 46-Key QWERTZ Keyboard Combinations Key Normal Shift + Nor
DRAFT COPY 11/11/11 Key Normal Shift + Normal Blue + Normal Red + Normal Down Navigation Down Down Volume Down Page Down Right Navigation Right Q q Q # (number sign) F1 W w W 1 F2 E e E 2 F3 R r R 3 F4 T t T + (plus) F5 Y y Y _ (underscore) F6 U u U - (minus) F7 I i I = (equal) F8 O o O “ (double quote) F9 P p P áU F10 A a A * (asterisk) S s S 4 D d D 5 F f F 6 G g G ( H h H ) J j J / (forward slash) K k K : (colon
DRAFT COPY 11/11/11 Key Normal Shift + Normal Blue + Normal X x X 8 C c C 9 V v V % (percent) B b B & (ampersand) N n N ! (exclamation mark) M m M ? (question mark) Comma , (comma) < @ , (comma) ENT Enter TAB Tab Back Tab Back Tab Tab Period . (period) > 0 .
7 DRAFT COPY 11/11/11 System Settings Overview Customized settings are available on the System Settings menu. Tap tings screen opens. > Settings and the set- Icon Description Bluetooth Configures the Bluetooth radio. See Working with the Bluetooth Radio on page 101. Clock & Alarms Set the system clock, date, time and schedule alarms. See Clock & Alarms on page 7-2. Lock Password protect the terminal to limit access to the terminal.
DRAFT COPY 11/11/11 Icon Description System Adjusts system settings. See System Menu on page 7-7. Microsoft My Phone This icon is present on Dolphin models equipped with WWAN radio (GSM/UMTS/ GPRS/EDGE) capabilities. Microsoft My Phone synchronizes your phone’s contacts, calendar, tasks, text messages, music, photos, videos, and other documents with your My Phone account at http://myphone.microsoft.com.
DRAFT COPY 11/11/11 Personal Menu To access the Personal Menu, tap the Personal Menu. > Settings > Personal . The screen opens displaying Icon Description Buttons Program the side buttons to perform specific tasks. See Buttons on page 7-3. Owner Information Enter your contact information (e.g., name, company, address, telephone number and E-mail address). Phone This Phone icon is present on Dolphin models equipped with WWAN radio (GSM/ UMTS/GPRS/EDGE) capabilities.
DRAFT COPY 11/11/11 Changing Button Assignments 1. After HotKeys is enabled, tap > Settings > Personal > Buttons . Note: The buttons that appear on this window are the only buttons that can be programmed via the Buttons setting. You cannot add buttons to this window. 2. To change button assignment, tap on the name of the button in the Button column, and then select a program or command in the Assign a program drop down list. 3. Tap OK to save. 4.
DRAFT COPY 11/11/11 Command Description Opens the menu or performs the action displayed on the right side of the Command bar. Changes the screen orientation from portrait to landscape. Activates the scanner/imager. Activates the scanner/imager. Scrolls down in the open application. Scrolls left in the open application. Scrolls right in the open application.
DRAFT COPY 11/11/11 3. Navigate to the Windows folder and open the Start Menu (My Device > Windows > Start Menu > Programs), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu. Note: If there is no blank space available in the window, tap on Menu > Edit > Paste Shortcut. 4. Tap to verify that the program now appears on the Start menu.
DRAFT COPY 11/11/11 System Menu The System menu enables you to verify and sometimes alter system parameters. To access the System menu, go to Start > Settings > System. Tap the appropriate icon to open that system setting. Icon See Page About See About on page 7-8. Backlight See Backlight on page 7-9. Battery See Battery on page 7-10. Certificates See Certificates on page 7-10. Encryption See Encryption on page 7-11. Error Reporting See Error Reporting on page 7-11.
DRAFT COPY 11/11/11 Icon See Page Five Volt Control See Five Volt Control on page 7-12. Managed Programs See Managed Programs on page 7-13. Memory See Memory on page 7-14. Power See Power on page 7-15. RIL See RIL on page 7-15. Regional Settings See Regional Settings on page 7-15. Remove Programs See Remove Programs on page 7-16. Screen See Screen on page 7-17. Smart Sensors See Smart Sensor on page 7-12. Task Manager See Task Manager on page 7-18.
DRAFT COPY 11/11/11 Backlight The Backlight system setting enables you to customize backlight functionality for the display. The backlight for the color display is user-defined. The Backlight system setting screen contains three tabs: Battery Power, External Power, and Brightness. Tap > Settings > System > Backlight. Battery Power Tab External Power Tab Brightness Tab The Battery Power tab determines the backlight timeout when the terminal is running on battery power.
DRAFT COPY 11/11/11 Battery The Battery system settings menu contains two tabs: Battery Status and Log Config. The Battery Status tab provides the status of the main battery pack (e.g., Battery Time to Full or Battery Time to Empty, Voltage, Current, Temperature, Chemistry, and Serial Number). The Log Config Tab allows you to configure the BatteryLogFile. Tap > Settings > System > Battery Battery Status Tab Log Config Tab When external power is supplied to the terminal, “Battery Time to Full” is listed.
DRAFT COPY 11/11/11 Encryption Encryption gives you the option of encrypting files placed on storage cards so that those files cannot be read by any other device. Error Reporting Error Reporting gives you the option of enabling or disabling the error reporting function of Windows Embedded Handheld 6.5. External GPS External GPS determines which port a third-party GPS software application can use to access the GPS receiver.
DRAFT COPY 11/11/11 Five Volt Control Five Volt Control gives you the option to manually enable 5V output to supply power to an external device. By default, 5-Volt Output automatically turns on when AC power is applied to the terminal. If you want to use a USB memory stick without AC power, then you must manually turn on the 5-Volt Output. Do not leave 5-Volt output enabled when you are not using it to supply power to an external device.
DRAFT COPY 11/11/11 Event Track displays an event log summary of detected free fall events exceeding 2 ft. over 250 ms. The summary includes the time, date, and duration of the most recent 50 events. Several options are provided for audible notification of free fall events. Accelerometer Calibration Tap Start to calibrate the integrated accelerometer sensor used for motion detection. When calibration is complete, the "Accelerometer Calibration Finished!" message window appears.
DRAFT COPY 11/11/11 Memory The Memory applet shows the capacity and usage of the Storage and Program portions of the Flash file system. The Storage portion includes the IPSM folder, which can be detailed under the Storage Card tab. When the Program portion becomes too full, you can use the Task Manager to remove any unneces- sary tasks. Main Screen This screen displays the usage statistics of the flash memory.
DRAFT COPY 11/11/11 RIL The RIL Information screen displays useful statistics for the GSM WAN Voice module (PH8). To verify whether or not the GSM radio is enabled, check the Dolphin Wireless Manager (see page 8-4). Power Power system settings contains two tabs: Battery and Advanced Tap > Settings > System > Power Battery Tab The battery tab displays the power level status of the main battery and the status of the backup battery. Note: The Backup Battery gauge registers either 0% or 100%.
DRAFT COPY 11/11/11 The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and the results appear on the screen. To see specific settings or to change a specific setting, tap on one of the items on the horizontal scroll bar (i.e., Region, Number, Date), make the change, and tap OK to save. Remove Programs Remove Programs enables you to remove programs installed on the terminal. Any program (usually CAB or DLL files) stored in the \\IPSM\Honeywell\Autoinstall fold
DRAFT COPY 11/11/11 Screen The Screen system setting contains three screens: General, Clear Type, and Text Size. General Screen Orientation The General screen enables you to set the dynamic screen rotation. Three choices of screen orientation are supported: Portrait, Landscape (right-handed), and Landscape (lefthanded). Align Screen The General Tab also allows you to re-align the screen. You need to re-align the screen if tapping buttons or icons with the stylus no longer seems to work appropriately.
DRAFT COPY 11/11/11 Text Size Screen The Text Size screen enables you to perform font scaling within certain views of the: • Home screen, • Contacts, • Calendar, • Messaging, and • Tasks. Font scaling means that you can increase or decrease the point size of the font on application windows. To change the font size, move the slider toward Smallest or Largest. The Example text changes to reflect the font change. Tap OK to save the new font size setting.
DRAFT COPY 11/11/11 Using the Task Manager Applications To view the status of the programs running on your mobile computer, tap the Menu button at the bottom of the screen, then tap View > Applications. From the application list, you can: • Tap and hold on an application, then tap Switch To on the pop-up menu. • Tap and hold on an application, then tap End Task or End All Tasks on the pop-up menu. Note: Anytime you stop a running program, it frees up memory.
DRAFT COPY 11/11/11 7 - 20
8 DRAFT COPY 11/11/11 Communication Connections Menu The Connections system setting provides access to the terminal’s various wireless communication options. Icon Tapping this icon… Beam Enable the terminal to receive incoming beams from devices using Bluetooth wireless technology. See Working with the Bluetooth Radio on page 10-1. Connections Opens Microsoft’s connections manager. See Connections Manager on page 8-2. Dolphin Wireless Manager Manages the wireless radios installed in the terminal.
DRAFT COPY 11/11/11 Connections Manager Microsoft’s Connections Manager sets up multiple network connections to Internet Service Providers (ISPs) via external modem. Do NOT enter connection parameters in the Connections Manager if: • you are using one of the on-board wireless radios to connect to a network. The Dolphin terminal uses the settings from each radio’s configuration utility to connect. The connections manager is used primarily to setup WAN modem dial up connections.
DRAFT COPY 11/11/11 • Proxy server connection Note: If you are connected to your ISP or private network during synchronization, the terminal should download the proper proxy settings during synchronization with the workstation. If these settings are not on your workstation or need to be changed, ask your ISP or network administrator for the proxy sever name, server type, port, type of Socks protocol used, and your user name and password.
DRAFT COPY 11/11/11 Dolphin Wireless Manager The Dolphin Wireless Manager provides a centralized interface that enables and disables all the onboard radios. Each radio has its own configuration program. The Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio. Tap on the Home screen to access the Dolphin Wireless Manager. OR 1. Tap once on the Title bar to access the Horzontal Scroll bar. 2. Tap . 3. Select, “Dolphin Wireless Manager”.
DRAFT COPY 11/11/11 4. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON. Note: If applicable, information about the radio appears in the rectangle. Accessing Radio Configuration Utilities Each radio has its own configuration utility that you can access by tapping Menu on the tile bar. Radio Type Menu Option 802.11a/b/g/n Tap WLAN Settings and the Honeywell WLAN Security Supplicant opens.
DRAFT COPY 11/11/11 Network Cards The Network Cards screen allows you to set and configure the type of Network Adapter the Network card in the terminal uses. You can modify the adapter settings (e.g., Name Servers or IP address) by tapping on the adapter type or highlighting the adatpter and tapping Edit at the bottom of the screen. Connecting and Synchronizing the Terminal and Workstation To synchronize data between the terminal and the workstation, ActiveSync (version 4.
DRAFT COPY 11/11/11 • Select which information types are synchronized, controling how much data is synchronized. For example, you can choose how many weeks of past appointments you want synchronized. Communication Types The 7800 terminal supports Hi-Speed USB communication (USB 2.0) via ActiveSync through the I/O Connector (see page 3-10) on the bottom panel of the terminal. The maximum data transfer rate is 480 Mbps. A USB cable and a Honeywell hardware peripheral (e.g.
DRAFT COPY 11/11/11 Synchronizing with the Host Workstation After setup, synchronization begins automatically whenever the terminal’s mechanical connector connects to a Dolphin peripheral that is connected to a host workstation with ActiveSync or Windows Mobile Device Center installed. For additional information visit the Microsoft Phone Web site (http://go.microsoft.com/fwlink/?LinkId=147001). Exploring the Terminal from the Workstation ActiveSync 1. Open the main ActiveSync window (on the desktop). 2.
DRAFT COPY 11/11/11 1. Download the program to the workstation from either the Internet or the install CD. You may see a single *.exe or setup.exe file, a *.cab file, or a *.dll file. Note: There may be several versions of files for different device types and processors. Select the file that matches the terminal’s processor. 2. Read any installation instructions, Read Me files, or documentation that comes with the program. Many programs provide special installation instructions. 3.
DRAFT COPY 11/11/11 Connecting the Terminal to a Wireless Network You connect the terminal to a wireless network through the on-board radio (802.11a/b/g/n, Bluetooth, and/or GSM/CDMA). Each radio has its own configuration utility and requires specific information about the wireless network to connect. Successful connection depends on your network infrastructure about which you will need specific information from your network administrator. WLAN (802.11a/b/g/n) The 7800 has a 2.4 GHz 802.11b/g/n - 5.
DRAFT COPY 11/11/11 ! To prevent data loss, back up all user data to an SD card or external memory device before performing an upgrade. Note: An active Microsoft ActiveSync or Windows Mobile Device Center connection between a host workstation and the Dolphin terminal may be required for some types of software upgrades. For additional information, see Connecting and Synchronizing the Terminal and Workstation on page 8-6. For information on File Provisioning on the 7800, see page 2-10.
DRAFT COPY 11/11/11 8 - 12
9 DRAFT COPY 11/11/11 Working with Wireless Wide AreaNetworking (WWAN) Overview The 7800 has two options for WWAN connectivity, a data+voice GSM/HSPA+/UMTS/GPRS/EDGE and CDMA/EVDO radio or a data only Gobi radio, which supports GSM/HSPA+/UMTS/GPRS/EDGE and CDMA/1xRTT/EVDO. GSM Short for Global System for Mobile communications, GSM is an open, non-proprietary wireless WAN system that is constantly evolving and growing.
DRAFT COPY 11/11/11 Signal Strength The signal strength of the WWAN connection is indicated by the number of bars that appear in the signal strength icon in the Title bar at the top of the window. Icon Indicates… The signal strength of the radio connection. The signal strength of the phone (voice) connection; see GSM/HSPA+ Global Radio Dolphin Models on page 9-3. The signal strength of the data connection; see Data Communication (GSM/HSPA+ Global Radio Dolphin Models) on page 9-7.
DRAFT COPY 11/11/11 Enabling the WWAN Radio By default, the WWAN radio is not enabled after a factory reset. Verify the status of the radio in the Dolphin Wireless Manager. Tap on the Home screen to access the Dolphin Wireless Manager. If the WWAN radio is OFF, tap the rectangle to enable or turn ON the radio. GSM/HSPA+ Global Radio Dolphin Models Voice Communication You can use the Dolphin terminal as a phone over the GSM radio.
DRAFT COPY 11/11/11 Volume Control & Blue Use the Dolphin keyboard to adjust the volume. To raise the volume, press the Blue modifier key + up arrow. To lower the volume, press the Blue modifier key + down arrow. & Blue Or Press the up or down arrow on the Volume Control button on the left side of the device to adjust the volume of the active speaker, see Volume Control Button on page 3-7.
DRAFT COPY 11/11/11 Sending Calls After the number is dialed, tap Talk Note: The or press the Send key . icon indicates that the phone is in use. Ending Calls While the phone call is live, tap End or End Key . Accessing Voice Mail Tap > Phone > Speed Dial > Voice Mail > Call. Note: Update the voice mail retrieval number by turning the phone OFF and then ON via the Dolphin Wireless Manager, see Enabling the WWAN Radio on page 9-3.
DRAFT COPY 11/11/11 Security The Security screen provides access to establish or change your security PIN. Check the box next to, “Require a PIN when the phone is used” to enable the PIN security feature. Services For each service, the phone reads settings from the network stored on the SIM card and then displays the available options from the carrier on the screen. To customize the settings, select it from the list and tap “Get Settings”.
DRAFT COPY 11/11/11 Network You can find, select, and set your preferred network order from the Network screen. Data Communication (GSM/HSPA+ Global Radio Dolphin Models) You set up data communication via the Connections Manager. The carrier on the SIM card is the ISP. System Requirements • The GSM radio must be enabled; see Enabling the WWAN Radio on page 9-3. • You must have an active SIM card with a DATA plan installed; see Installing a SIM Card and/or Memory Card on page 3-16.
DRAFT COPY 11/11/11 3. Enter a name for the connection. Select Cellular Line (GPRS) as the modem. Tap Next. 4. Enter the Access point name. Tap Next. 5. Enter the username and password from the account. Tap Finish.
DRAFT COPY 11/11/11 6. The connection you just created should appear in the list on the modem tab. 7. Tap and hold on the connection. Select Connect on the popup menu. 8. The network icon in the Title bar indicates the GSM radio is attempting to connect . Note: When the device is on a 2G (EDGE/GPRS) network, a data connection failure occurs if the phone is in use for a voice call while attempting a data connection. Simultaneous voice and data use is only supported if the device is on a 3G network.
DRAFT COPY 11/11/11 Manual Network Selection You can select Automatic or Manual network selection. The Phone defaults to Automatic network selection. 1. When an active SIM card is inserted in the terminal, tap > Settings > Personal > Phone > Menu > Options. 2. Select the Network tab. 3. Under Network selection, select Automatic (the default selection) or Manual. a. If you select Manual, the Phone searches for available networks. b. The found networks appear. c. Select a new network and tap OK.
DRAFT COPY 11/11/11 Data Communication GSM/CDMA Dolphin Models Gobi Manager The Gobi Manager enables you to see real time status of the radio, setup your Network selection, view you’re profile and scan for networks. The Gobi Manager contains four tabs: Status, Setup, Profile, and About. 1. Tap on the Home screen to access the Dolphin Wireless Manager. 2. Tap Menu. 3. Select Gobi Settings.
DRAFT COPY 11/11/11 The Profile tab allows you to see Radio capability information and network statistics including: Profile Tab • • • • About Tab Radio Hardware and Software versions Radio and SIM identification numbers Serving network connection type and state Available radio interfaces for the current serving network Displays copyright and version information for the Gobi Connection Manager. Establishing Data Communication 1. Tap on the Home screen to access the Dolphin Wireless Manager. 2.
10 DRAFT COPY 11/11/11 Working with the Bluetooth Radio Enabling the Bluetooth Radio You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 8-4). 1. Tap on the Home screen to access the Dolphin Wireless Manager. 2. Tap anywhere inside the Bluetooth rectangle and Bluetooth begins activating. 3. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON. Now, the Bluetooth radio is transmitting a signal.
DRAFT COPY 11/11/11 Pairing and Trusted Devices The terminal does support pairing. Pairing happens during general connection setup. Paired devices are "trusted" devices. This means that there is unrestricted access to all services (including services that require authorization and authentication). A connection can exclude pairing. A device that is connected to the terminal but not paired with it is considered an untrusted device.
DRAFT COPY 11/11/11 4. Select a device from the list and tap Next. The types of devices in the vicinity of the radio appear in the list of discovered devices. 5. You are prompted to enter a passcode. • If the device has a specific passcode, enter it in the Passcode field and tap Next. When attempting to connect to a printer or headset with Bluetooth capabilities, the passcode may default to either 1111 or 0000. If there is no default, consult the device literature for the number.
DRAFT COPY 11/11/11 8. When the connection is complete, a list of matching and supported services on the device appears. Only the services that are mutually supported on both devices appear in the Partnership Settings window. 9. Select the services you want to use and tap Save. The services on the new devices have to be selected or the pairing won’t include those services, even though the devices are paired. If services are not selected, you will be continually re-prompted for the passcode from the device.
DRAFT COPY 11/11/11 Transferring Files Before attempting to transfer files, make sure the receiving Bluetooth device is in range, set to be discoverable by other devices, and set to receive incoming beams. 1. Tap > File Explorer. 2. Navigate to the file you want to transfer. 3. Tap and hold on the file and select Beam File on the popup menu. 4. The Bluetooth radio begins searching for devices.
DRAFT COPY 11/11/11 7. When the file is being transferred, the selected device reads “Sending”. Making the Terminal Discoverable By default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by other Bluetooth devices. 1. To make the terminal discoverable, tap > Settings > Bluetooth . Note: If you are in the Dolphin Wireless Manager, tap Menu > Bluetooth Settings. 2. Tap Mode on the Horizontal scroll. 3.
DRAFT COPY 11/11/11 Selecting COM Ports You can select COM ports 0-9. For more information, see 7800 COM Port Assignment Table on page 811.
DRAFT COPY 11/11/11 10 - 8
11 DRAFT COPY 11/11/11 Working with GPS Overview The Dolphin 7800 terminal contains an integrated GPS module that allows location tracking of workers and vehicles, providing better utilization of field assets. Optional mapping and navigation software provides turn-by-turn driving directions and location information.
DRAFT COPY 11/11/11 GPS Intermediate Driver When the first user of GPD1 opens the port, the GPS Intermediate Driver opens the COM7 port. The GPS Intermediate Driver allows multiple applications to open GPD1, and the GPS data is broadcast to all open ports. When the GPSID driver is in use, the COM7 port is allocated to GPSID as READ|WRITE (COM7 is still available for access mode of 0). For more information about Microsoft’s GPS Intermediate Driver, follow this link: http://msdn.microsoft.
12 DRAFT COPY 11/11/11 Dolphin 7800HomeBase Device (Model 7800-HB) Overview The Dolphin 7800 HomeBase (Model 7800-HB) is a charging and communication cradle that supports USB Hi-Speed 2.0v communication, which enables the terminal to interface with the majority of PCbased enterprise systems. The HomeBase also contains an auxiliary battery well that charges a spare Honeywell standard or extended battery pack.
DRAFT COPY 11/11/11 Convenient Storage The intelligent battery charging system makes this base a safe and convenient storage receptacle for your Dolphin terminal. Capacity The base holds one terminal and features an auxiliary battery well behind the terminal well that can charge a battery pack independently of the terminal well. This means that one base can charge two battery packs: the one installed in the terminal and a spare. ! ! We recommend use of Honeywell Li-ion battery packs.
DRAFT COPY 11/11/11 AUX Battery LED Indicates status of the battery charging in the auxiliary battery well; see Back Panel on page 12-3. This color means… Orange The auxiliary battery is charging. Green The auxiliary battery has completed charging and is ready for use. Red, Flashing The internal temperature of the auxiliary battery is too hot or there is a battery error. Charge the auxiliary battery in a cooler environment or replace the battery with a new Honeywell battery.
DRAFT COPY 11/11/11 USB Port This USB port is USB v2.0 Hi-Speed compliant. Using a USB cable, you can connect the base to a host device, such as a workstation. USB communication occurs through Microsoft ActiveSync (v4.5 or higher) or Microsoft Windows Mobile Device Center (WMDC) depending on the host workstation’s operating system. When the terminal is seated in the terminal well, it is connected to the host device via the base.
DRAFT COPY 11/11/11 Charging the Main Battery The base provides power to the Dolphin terminal and allows the charging of the terminal’s main battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be stored in the base indefinitely without damage to the terminals, battery packs, or the base.
DRAFT COPY 11/11/11 Communication Dolphin terminals support USB communications out of the box. The base also supports USB communications via the USB port located on the back. The base acts as a USB device by interfacing the USB signals of the Dolphin terminal to the USB of the host workstation. Using a standard USB cable, the base’s USB interface allows the Dolphin terminal to communicate with a workstation.
DRAFT COPY 11/11/11 Mounting the HomeBase Set the base on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal while it is in the base. When choosing a mounting location, bear in mind that the location must allow users' easy access to the Auxiliary Battery Well and the back panel of the HomeBase where the USB port and the power jack are located.
DRAFT COPY 11/11/11 12 - 8
13 DRAFT COPY 11/11/11 Dolphin 7800eBase Device (Model 7800-EHB) Overview The Ethernet Base (eBase) enables a single Dolphin 7800 computer to communicate with a host device over an Ethernet network. The 7800-EHB charger is designed for use with standard battery pack model 7800-BTSC or 7800BTSCW (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack model 7800-BTXC or 7800-BTXCW ( Liion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc. and with Dolphin 7800 model terminals.
DRAFT COPY 11/11/11 Capacity The base holds one terminal and features an auxiliary battery well behind the terminal well that can charge a battery pack independently of the terminal well. This means that one base can charge two battery packs: the one installed in the terminal and a spare.
DRAFT COPY 11/11/11 This color means… Red Flashing The internal temperature of the auxiliary battery is too hot or there is a battery error. Charge the auxiliary battery in a cooler environment or replace the battery with a Honeywell battery. COMM LED The COMM LED indicates the status of data transfer between the Dolphin terminal and the eBase.
DRAFT COPY 11/11/11 USB Port This USB port is USB v2.0 Hi-Speed compliant. Using a USB cable, you can connect the eBase to a USB compliant device to facilitate USB communication to and from the terminal. USB communication occurs through Microsoft ActiveSync (v4.5 or higher) or Microsoft Windows Mobile Device Center depending on the host workstation’s operating system. When the terminal is seated in the terminal well, it is connected to the peripheral device via the eBase.
DRAFT COPY 11/11/11 Connecting Power to the eBase Power Adapter 1. Plug the A/C power cord into the power adapter. 2. Plug the power cable into the power connector on the back of the eBase. A/C Power Cord 3. Plug the A/C power cord into a grounded power source. The Power/Dock LED on the eBase illuminates solid red to indicate the eBase has power and no terminal is docked.
DRAFT COPY 11/11/11 1. Insert the battery at an angle. Note: Align the battery contacts with the contacts inside the auxiliary battery well. 2 2. Snap the battery into place with a hinging motion. The Aux Battery LED lights orange. 1 3. Use the AUX Battery LED to monitor the charging progress. The LED lights green when the auxiliary battery has completed charging and is ready for use.
DRAFT COPY 11/11/11 Displaying the eBase and Terminal IP Address Once the Dolphin terminal has been successfully connected to the eBase, the terminal uses the eBase IP address. This IP address can be used by any application on the Dolphin terminal. 1. Tap > Power Tools > Network Utilities > IPConfig. 2. Change the Adapter to SMC95001. 3. On the Input tab, tap the Display full configuration button. 4. The Dolphin terminal retrieves and displays the IP configuration for the entire terminal and eBase.
DRAFT COPY 11/11/11 Optional Hardware Mount On the bottom of the HomeBase there are four mounting holes with a maximum depth of 7 mm that can be used to secure the base to a horizontal surface such as a desktop or workbench using M3 self tapping screws. Optional Mounting Holes for M3 self tapping screws, Qty. 4. Maximum thread depth of 7 mm. 98 mm [3.86 in.] 13 - 8 CL 101 mm [3.98 in.] 90 mm [3.54 in.
14 DRAFT COPY 11/11/11 Dolphin 7800Mobile Base Device (Model 7800-MB) Overview The Dolphin Mobile Base charging cradle is designed specifically for in-premise and in-transit data collection applications. The base features a mounting bracket and a cigarette lighter adapter to adapt it to your environment. The 7800-MB charger is designed for use with Dolphin 7800 model terminals using standard battery pack model 7800-BTSC or 7800-BTCW ( Li-ion 3.7 V, 8.
DRAFT COPY 11/11/11 Mobile Base Components Terminal Well Mounting Back Plate Power Adapter Terminal Locking Lever Adapter Power LED (not in view) Mounting Back Plate Used to mount the base to a fixed location. Terminal Locking Lever The mobile base has a locking lever on the front. When the lever is in the down position the terminal in locked in the base. To unlock the terminal push the lever up. Terminal Well Place the terminal in this well to charge the main battery pack.
DRAFT COPY 11/11/11 Back Panel and Mounting Brackets Ball Joint Pivot Bracket Base Mounting Bracket Turnscrew Ball Joint Ball Joints There are two ball joints: one that is attached to back of the base and one on the mounting bracket. Both ball joints are inserted into the bracket and secured to mount the base. Pivot Bracket The bracket contains the turnscrew and two slots. Ball joints are inserted into each slot and secured with the turnscrew.
DRAFT COPY 11/11/11 ! Do not install the Mobile base in an air bag deployment zone. Honeywell assumes no responsibility of liability for injury or death because of car crashes and/or air bag deployment. ! Do not mount the base in a location where it prevents safe operation of the vehicle and/or impedes the vehicle operator's field of view. ! Do not mount the base in a location where the connectors on the bottom panel of the base are not easily accessible.
DRAFT COPY 11/11/11 2. Plug the power adapter into the vehicle power outlet (e.g., cigarette lighter outlet). 3. Lift the base locking latch up. 4. Slide the Dolphin into the terminal well and lower the locking latch. Charging begins immediately if required by the Dolphin terminal.
DRAFT COPY 11/11/11 14 - 6
15 DRAFT COPY 11/11/11 Dolphin 7800ChargeBase Device (Model 7800-CB) Overview The 7800 ChargeBase is a 4-slot charging cradle that can power 4 Dolphin terminals, and charge their main batteries in 4 hours for the standard battery or 6 hours for the extended battery. The 7800-CB charger is designed for use with Dolphin 7800 model terminals using one of the following battery pack models: standard battery pack model 7800-BTSC (Li-ion 3.7 V, 8.
DRAFT COPY 11/11/11 Parts and Functions Front Panel Terminal Wells (Qty. 4) Power/Dock LED (Qty. 4) Charge LED (Qty. 4) Terminal Wells The base contains four terminal wells. Each well has its own dedicated Power/Docking LED and Charging LED indicator. Power/Dock LEDs The Power/Dock LED indicates if the ChargeBase has power and if the terminal is properly seated in the terminal well. Each terminal well has its own dedicated Power/Dock LED.
DRAFT COPY 11/11/11 Back Panel Power Supply Connector Power Supply Connector This connector receives input from the power adapter. Plug the power connector cable from the power adapter into this connector. Power The terminal requires 12 Volts DC input for battery charging; the power adapter on the power cable converts the voltage from the power source to 12 volts DC. Use only a UL Listed power supply, which has been qualified by Honeywell with output rated at 12VDC and 8.5 amps with the device.
DRAFT COPY 11/11/11 Charging the Main Battery The base provides power to the Dolphin terminal(s) and allows charging of the main batteries in the terminals. The main battery of each terminal charges in 4 hours for the standard battery or 6 hours for the extended battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be seated in the base indefinitely without damage to the terminals, battery packs, or the base.
DRAFT COPY 11/11/11 Desk Mounting The DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface. Hardware Required • 3/16 in. dia x 5/8 in. long pan head screw • 1/2 in. OD x 7/32 in. ID x 3/64 in. thick • 3/16 in. dia nut Installing the DIN Rail 1. Slide the DIN Rail into the DIN Rail slot on the bottom panel of the base. 2. Turn the base and DIN Rail right side up. 3.
DRAFT COPY 11/11/11 15 - 6
16 DRAFT COPY 11/11/11 Dolphin 7800Net Base Device (Model 7800-NB) Overview The Net Base enables up to four Dolphin 7800 mobile computers to communicate with a host device over an Ethernet network. In addition, the Net Base provides a second RJ45 Ethernet port for connection to an additional device such as a printer, workstation, eBase, or another Net Base. The 7800-NB charger is designed for use with Dolphin 7800 model terminals using standard battery pack model 7800-BTSC (Li-ion 3.7 V, 8.
DRAFT COPY 11/11/11 Parts and Functions Front Panel Terminal Wells (Qty. 4) Power/Dock LED (Qty. 4) COMM LED (Qty. 4) Terminal Wells The Net Base contains four terminal wells. Each well has its own dedicated Power/Dock LED and COMM LED indicator. Place the Dolphin terminal in any one of the four wells to communicate with a host device, power the terminal, and charge the installed battery pack.
DRAFT COPY 11/11/11 Back Panel Green LED (Qty. 1 Per Port) Yellow LED (Qty. 1 Per Port) Port 1: 10/100Mbps RJ45 Ethernet Port DC Power Jack Port 2: 100Mbps Only RJ45 Ethernet Port DC Power Jack This connector receives input from the power adapter. Plug the power connector cable from the power adapter into this connector, see Power on page 16-4. RJ45 Ethernet Ports The Net Base contains two RJ45 Ethernet ports.
DRAFT COPY 11/11/11 Bottom Panel For details on how to mount the Net Base, see Mounting the Net Base on page 16-6. MAC Address Label Compliance Label Serial Number Label Power The terminal requires 12 Volts DC input for communications and battery charging; the power adapter on the power cable converts the voltage from the power source to 12 volts DC. Use only a UL Listed power supply with output rated 12VDC, 8.5A with the device, which has been qualified by Honeywell.
DRAFT COPY 11/11/11 Charging the Main Battery The base provides power to the Dolphin terminals and allows the charging of the main batteries in the terminals. The main battery of each terminal charges in 4 hours for the standard battery or 6 hours for the extended battery. The intelligent battery charging system incorporated into all Dolphin terminals prevents overcharging, which means that Dolphin terminals may be stored in the base indefinitely without damage to the terminals, battery packs, or the base.
DRAFT COPY 11/11/11 Connecting the Dolphin Terminal to the Net Base By default, the Dolphin terminal is configured to obtain IP addresses automatically using a DHCP server. This means that in most cases, you would simply plug-and-play the unit. 1. Verify the base has power. If the Power/Dock LEDs are not illuminated, see Connecting Power to the Net Base on page 16-4. 2. Plug the CAT-5 Ethernet cable into one of the RJ45 connectors on the back of the Net Base. 3. Plug the Ethernet cable into the network. 4.
DRAFT COPY 11/11/11 Bottom Panel DIN Rail Slot Rubber Feet, Qty. 8 Optional Mounting Holes for M3 self tapping screws, Qty. 4. Maximum thread depth of 7 mm. Desk Mounting The DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface. Hardware Required • 3/16 in. dia x 5/8 in. long pan head screw • 1/2 in. OD x 7/32 in. ID x 3/64 in. thick • 3/16 in. dia nut Installing the DIN Rail 1. Slide the DIN Rail into the DIN Rail slot on the bottom panel of the base. 2.
DRAFT COPY 11/11/11 3. Then, using the appropriate nuts and bolts, secure the DIN Rail to a stable, flat horizontal surface. DIN Rail (7.
17 DRAFT COPY 11/11/11 Dolphin 7800QuadCharger Device (Model 7800-QC) Overview This 4-slot charging station provides intelligent battery management for the rechargable battery packs used in Dolphin terminals. The 7800-QC charger is designed for use with standard battery pack model 7800-BTSC or 7800BTSCW (Li-ion 3.7 V, 8.9 watt hour) and extended battery pack model 7800-BTXC or 7800-BTXCW (Liion 3.7 V, 14.8 watt hour) manufactured for Honeywell International Inc.
DRAFT COPY 11/11/11 Parts and Functions Top Panel Power Supply Connector Support Legs Qty. 2 Status LEDs Qty. 1 Per Charging Slot Charging Slots Qty. 4 Power LED Charging Slots There are four charging slots. Each slot holds one battery and charges it independently of the other slots. Charging immediately begins when a battery is placed in a slot. Power LED The power LED indicates if the QuadCharger is powered. When the QuadCharger is receiving power, the LED illuminates green.
DRAFT COPY 11/11/11 Power The charger must be connected to a power source via the Honeywell power adapter cable so that voltage is adjusted appropriately. Use only a UL listed power supply, which has been qualified by Honeywell with output rated at 12VDC and 3 amps with the device. AC Power Cord Power Cable 1. Plug the AC power cord into the power adapter. 2. Plug the power cable into the power connector on the back of the charger. Power Adapter Power Supply Connector Power LED 3.
DRAFT COPY 11/11/11 Mounting the QuadCharger The charger should be located on a dry, stable surface and can be mounted on a flat, horizontal surface such as a desktop or workbench. When choosing a location, always bear in mind that: • the mounting location must allow users easy access to the power connector. • the charger should be oriented so that users can easily insert and remove battery packs and see the status LEDs. Optional Hardware Mount Bottom Panel 268.6 mm [10.57 in.] 93 mm [3.66 in.] 45mm [1.
DRAFT COPY 11/11/11 Troubleshooting If you encounter problems with your QuadCharger device, refer to chart below for possible solutions. If problems persist, please contact Honeywell Technical Support. Problem Issue The Status LED does not come on when I insert a battery pack. Check the power connections; make sure the Power cable is inserted into the Power supply connector and the battery pack is properly seated. The Status LED lights red during charging.
DRAFT COPY 11/11/11 17 - 6
18 DRAFT COPY 11/11/11 Customer Support Product Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product. North America Telephone: (800) 782-4263 E-mail: hsmnaservice@honeywell.
DRAFT COPY 11/11/11 For ongoing and future product quality improvement initiatives, the 7800 comes equipped with an embedded device lifetime counter function. Honeywell may use lifetime counter data for future statistical reliability analysis as well as ongoing quality, repair and service purposes.
DRAFT COPY 11/11/11 Limited Warranty Honeywell International Inc. ("HII") warrants its products and optional accessories to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment.
DRAFT COPY 11/11/11 How to Extend Your Warranty Honeywell International Inc. offers a variety of service plans on our hardware products. These agreements offer continued coverage for your equipment after the initial warranty expires. For more information, contact your Sales Representative, Customer Account Representative, or Product Service Marketing Manager from Honeywell International Inc., or your Authorized Reseller.
DRAFT COPY 11/11/11
DRAFT COPY 11/11/11 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.
